Battery ACURA CSX 2006 Service User Guide

Î
ÎÎ
(#'
) Specification
Electric Current: 80 A or less
4-9
Starter Performance Test
STARTER
S
B
S STARTER B STARTER
S
B
1. Remove the starter (see page 4-10).
2. Make the connections for this test using the thickest
(gauge) wire possible (preferably the same gauge
as used on the vehicle).
NOTE: To avoid damaging the starter, never leave
the battery connected for more than 10 seconds.
3. Connect the battery as shown, and check for continuity between the B terminal and the starter
body. If there is continuity, it is working properly.
4. Disconnect the battery from the starter body, and check for continuity between the B terminal and the
starter body. If there is no continuity, it is working
properly. 5. Firmly clamp the starter in a vise.
6. Connect the starter to the battery as shown, and
confirm that the motor runs.
7. If the electric current meets the specification when the battery voltage is at 11.5 V, the starter is
working properly.
08/08/21 14:09:23 61SNR030_040_0010
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
Removal
K20Z2 engine
K20Z3 engine
4-10 Starting System
Starter Removal and Installation
1. Do the battery terminal disconnection procedure
(see page 22-68).
2. Remove the splash shield. 3. Remove the intake manifold bracket.
08/08/21 14:09:24 61SNR030_040_0011
ProCarManuals.com
DYNOMITE -2009-



K20Z2 engine
K20Z3 engine
4-12 Starting System
Starter Removal and Installation (cont’d)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
4. Install the intake manifold bracket. 5. Install the splash shield.
6. Do the battery terminal reconnection procedure (see page 22-68).
7. Start the engine to make sure the starter works properly.
08/08/21 14:09:25 61SNR030_040_0013
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
4-19
Circuit Diagram
ICM
ICM ICM
ICM: Ignition Conotrol Module BLK BLK BLK
ICM
BLK/WHT BLK/WHT BLK/WHT BLK/WHT
5V
BLU
ECM/PCM
IGPLS4 IGPLS3 IGPLS2 IGPLS1 MRLY BLK/WHT
2 3
1 UNDER-HOOD FUSE/RELAY BOX
1
3 2
4
No. 18 (15 A)
GRN
No. 4 WHT/BLU
No. 3 No. 2 BLU/RED
BATTERY
YEL/GRN
BLK No. 1
BRN
G101G101 IGNITION
COIL
RELAY
IGNITION
COILS
SPARK
PLUGS E7
F9
C18 C17 C16 C15 A6
13 3
1
3
1
2
2
2 23
16
C101
08/08/21 14:09:30 61SNR030_040_0020
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
4-23
Charging System
Component Location Index
BATTERY
DRIVE BELT CHARGING SYSTEM INDICATOR
(In the gauge control module (tach))
UNDER-HOOD FUSE/RELAY BOX
(Has built-in ELECTRICAL LOAD
DETECTOR (ELD))
ALTERNATOR
DRIVE BELT AUTO-TENSIONER
IDLER PULLEY
Test, page 22-67
Inspection, page 4-30
Replacement, page 4-31 Removal and Installation, page 4-34
Overhaul, page 4-38
Inspection, page 4-31
Removal/Installation, page 4-32
Tensioner Pulley Replacement,
page 4-33
Replacement,
page 4-34
08/08/21 14:10:10 61SNR030_040_0024
ProCarManuals.com
DYNOMITE -2009-

(#'

)
Symptom Diagnostic procedure Also check for
4-24
Charging System
Symptom Troubleshooting Index
Charging system
indicator does not come
on with the ignition
switch in ON (II)
Troubleshoot the charging system indicator circuit
(see page 4-26).
Charging system
indicator stays on 1.
2.
3.
4.Troubleshoot the charging system indicator circuit
(see page 4-26).
Check for a broken drive belt (see page 4-30).
Check the drive belt auto-tensioner (see page 4-31).
Check for PGM-FI DTCs (see page 11-3).
Battery discharged 1. 2.
3.
4.
5.
6.Check for a poor connection at the battery terminal.
Check for a broken drive belt (see page 4-30).
Test the battery (see page 22-67).
Troubleshoot the alternator and regulator circuit
(see page 4-28).
Check the drive belt auto-tensioner (see page 4-31).
Check for excessive parasitic electrical current draw
with the ignition switch to LOCK (0), and the key
removed. The multiplex control unit may take up to 10
minutes to turn off (sleep mode) for same models.
Battery overcharged 1. 2.Test the battery (see page 22-67).
Troubleshoot the alternator and regulator circuit
(see page 4-28).
08/08/21 14:10:10 61SNR030_040_0025
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
4-25
Circuit Diagram
6
3
191 F5
17 D2
A3
A2 H1
ELD
CANL
CANH
ALTF ALTC ALTL
5V
ALTERNATOR DRIVER
YEL
FR L C IG BRN
ELD
A23 GAUGE CONTROL MODULE (TACH)
IGNITION SWITCH
BATIG1
B43 B42 B41 A37
A36 RED
WHT CPU
YEL
1
BLK/YEL
No. 2 (50 A)
BLK
RECTIFIER
BATTERY
VOLTAGE REGULATOR2
3
4
B
BLK
G301
UNDER-HOOD FUSE/RELAY BOX
No. 1 (100 A)
ORN
WHT/RED WHT/GRNWHT/BLU UNDER-DASH
FUSE/RELAY BOX
CHARGING
SYSTEM
INDICATOR
IG1 HOT in ON (II)
and START (III)
A1
ECM/PCM BLU
Q9
WHT
22
17C101
CANH
CANL
YEL
No. 10
(7.5 A)
No. 3
(10 A)
08/08/21 14:10:10 61SNR030_040_0026
ProCarManuals.com
DYNOMITE -2009-

µÌ
Ï
Î
(#'


)
µ
µ µ
µ
Special Tools Required
YES
NO YES
NO
4-28
Charging System
Alternator and Regulator Circuit Troubleshooting
OTC3131
Alternator, Regulator, Battery & Starter tester OTC3131
Available through the Honda Canada Inc. Technical
Tools Department; FAX
866-398-8665/e-mail:
ch_technicaltools ch.honda.com
1. Make sure the battery connections are good and the battery is sufficiently charged.
2. Connect the alternator, regulator, battery & starter tester (OTC3131) to the battery as shown.
3. Start the engine. Hold the engine speed at 3,000 rpm with no load (in N or P (A/T model) or
neutral (M/T model)) until the radiator fan comes
on, then let it idle.
4. Do the CHARGING SYSTEM TEST.
Go to step 5.
If the voltage is less than 13.5 V, go to
alternator control circuit troubleshooting (see page
4-29). If the voltage is over 15.1 V and amperage is
less than 87.5 A, replace the alternator (see page
4-34) or repair the alternator (see page 4-38). 5. Check the diode condition on the display.
The diode is OK. Troubleshooting is
complete.
If the display indicates BAD, replace the
alternator (see page 4-34) or repair the alternator
(see page 4-38), then retest.
NOTE: If the display indicates N/A, the diode
pattern could not be diagnosed. Repeat the test
again. If test is complete, use multimeter to
perform further pinpoint testing, then retest.
Does the display indicate the voltage is within 13.5 15 .1 V t he amper age i s 87 .5 A or mor e? Does t he d i spl ay i nd i cat e GOOD?
08/08/21 14:10:11 61SNR030_040_0029
ProCarManuals.com
DYNOMITE -2009-



(#'


)
µ
µ µ
µ
YES
NO YES
NO
4-29
Alternator Control Circuit Troubleshooting
BATTERY
ALTERNATOR
4P CONNECTOR C (WHT/GRN) ALT C
(WHT/GRN)
ECM/PCM CONNECTOR B (44P)
1. Connect the Honda Diagnostic System (HDS) to the
data link connector (DLC) (see step 2 on page 11-3).
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain
control module (PCM). If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
4. Check for DTCs (see page 11-3). If a DTC is present, diagnose and repair the cause before continuing
with this test.
5. Disconnect the alternator 4P connector.
6. Start the engine, and turn on the headlights to high beam.
7. Measure the voltage between alternator 4P connector terminal No. 2 and the positive terminal
of the battery.
Go to step 11.
Go to step 8.
8. Jump the SCS line with the HDS, then turn the ignition switch to LOCK (0).
NOTE: This step must be done to protect the ECM/
PCM from damage.
9. Disconnect ECM/PCM connector B (44P). 10. Check for continuity between ECM/PCM connector
terminal B41 and body ground.
Repair short to ground in the wire between
alternator 4P connector terminal No. 2 and ECM/
PCM connector terminal B41.
Update the ECM/PCM if it does not have the
latest software (see page 11-227), or substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the symptom/indication goes away with
a known-good ECM/PCM, replace the original ECM/
PCM (see page 11-228).
11. Jump the SCS line with the HDS, then turn the ignition switch to LOCK (0).
NOTE: This step must be done to protect the ECM/
PCMfromdamage.
12. Disconnect ECM/PCM connector B (44P).
(cont’d)
Wire side of
female terminals Terminal side of female terminals
Is t her e 1 V or l ess?
Is there continuity?
08/08/21 14:10:12 61SNR030_040_0030
ProCarManuals.com
DYNOMITE -2009-


(#'

 )

(#'



 )
Removal
4-344-34 Charging System
Idler Pulley Replacement
Alternator Removal and Installation
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
AB
C
A
C
C C
1. Remove the drive belt (see page 4-31).
2. Remove the idler pulley.
3. Install the idler pulley in the reverse order of
removal. 1. Do the battery terminal disconnection procedure
(see page 22-68).
2. Remove the drive belt (see page 4-31).
3. Remove the front grille cover (see page 20-163).
4. Disconnect the fan motor connectors (A) and the hood switch connector (B), then remove the
harnessclamps(C).
08/08/21 14:10:14 61SNR030_040_0035
ProCarManuals.com
DYNOMITE -2009-