door lock ACURA CSX 2006 Service User Guide



20-13
Fastener Location:Screw,1
AB
A
A
B
B
C
9. Remove the screw, then remove the latch protector
(A) by releasing the hook (B).
10. Disconnect the latch cable (A) and the inner handle cable (B) from the latch (C). 11. Install the latch in the reverse order of removal, and
note these items:
 Make sure the actuator connector is plugged in properly and each rod is connected securely.
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:01 61SNR030_200_0015
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

20-14 Doors
Front Door Glass and Regulator Replacement
E
D
A B
EF B
D
C
Fastener Locations :Bolt,2
A
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) A
B
C
D
E
E
D
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) Fastener Locations
:Bolt,2
D:Bolt,2 E
(Black) (Gold)
NOTE: Put on gloves to protect your hands.
1. Remove the door panel (see page 20-7).
2. Disconnect the power door lock actuator connector (A) and remove the plug caps (B).
3. Pass the cables (C) and the harnesses (D) through the slits (E) in the plastic cover (F), then remove the
plastic cover.
4. Carefully raise the glass (A) until you can see the bolts, then remove them. Carefully pull the glass
out through the window slot. Take care not to drop
the glass inside the door. 5. Disconnect the connector (A), and detach the
harness clip (B) from the regulator (C).
6. Remove the bolts (D), and loosen the bolts (E), then remove the regulator through the hole in the door.
08/08/21 14:59:02 61SNR030_200_0016
ProCarManuals.com
DYNOMITE -2009-



(#'


 )

20-1520-15
Front Door Glass Outer
Weatherstrip Replacement
A A B
B
A
A
7. Apply multipurpose grease to all the sliding surfaces of the regulator (A) where shown.
8. Install the glass and regulator in the reverse order of removal, and note these items:
 Roll the glass up and down to verify it moves freely without binding.
 Make sure that there is no clearance between the glass and glass run channel when the glass is
closed.
 Adjust the position of the glass as necessary (see page 20-28).
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
 Make sure the power door locks, the windows and the power mirror operate properly.
 Test-drive and check for wind noise and rattles. NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
1. Lower the glass fully.
2. Release the front hook (A) from inside of the door, then pull up the front door glass outer weatherstrip
(B).
3. Starting at the front, slowly pull up the front door glass outer glass weatherstrip (A).
(cont’d)
08/08/21 14:59:02 61SNR030_200_0017
ProCarManuals.com
DYNOMITE -2009-



(#'


 )

20-1520-15
Front Door Glass Outer
Weatherstrip Replacement
A A B
B
A
A
7. Apply multipurpose grease to all the sliding surfaces of the regulator (A) where shown.
8. Install the glass and regulator in the reverse order of removal, and note these items:
 Roll the glass up and down to verify it moves freely without binding.
 Make sure that there is no clearance between the glass and glass run channel when the glass is
closed.
 Adjust the position of the glass as necessary (see page 20-28).
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
 Make sure the power door locks, the windows and the power mirror operate properly.
 Test-drive and check for wind noise and rattles. NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
1. Lower the glass fully.
2. Release the front hook (A) from inside of the door, then pull up the front door glass outer weatherstrip
(B).
3. Starting at the front, slowly pull up the front door glass outer glass weatherstrip (A).
(cont’d)
08/08/21 14:59:02 61SNR030_200_0017
ProCarManuals.com
DYNOMITE -2009-




(#'


 )
20-1620-16 Doors
Front Door Glass Outer
Weatherstrip Replacement (cont’d)
Front Door Weatherstrip
Replacement
A
B
A
Fastener Locations :Bolt,1
A :Clip,14
B
:Clip,2
C
:Clip,1
D
B
C
AC
F
E D
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) E
(White)
(Black) (Left: Pink
Right: Blue)
4. Slide the front door glass outer weatherstrip (A)
forward.
5. Twist the front door glass outer weatherstrip (A) to pull the rear hook (B) out from the inside of the
door, then remove the weatherstrip.
6. Push the clip portions of new front door glass outer weatherstrip into place securely. NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
 Remove the clips with a clip remover.
1. At the A-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E).
3. Install the weatherstrip in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Make sure the weatherstrip is installed in the holder (F) securely.
 Apply medium strength liquid thread lock to door checker mounting bolt before installation.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:03 61SNR030_200_0018
ProCarManuals.com
DYNOMITE -2009-




(#'


 )
20-1620-16 Doors
Front Door Glass Outer
Weatherstrip Replacement (cont’d)
Front Door Weatherstrip
Replacement
A
B
A
Fastener Locations :Bolt,1
A :Clip,14
B
:Clip,2
C
:Clip,1
D
B
C
AC
F
E D
8x1.25mm
29 N·m
(3.0 kgf·m, 22 lbf·ft) E
(White)
(Black) (Left: Pink
Right: Blue)
4. Slide the front door glass outer weatherstrip (A)
forward.
5. Twist the front door glass outer weatherstrip (A) to pull the rear hook (B) out from the inside of the
door, then remove the weatherstrip.
6. Push the clip portions of new front door glass outer weatherstrip into place securely. NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the door.
 Remove the clips with a clip remover.
1. At the A-pillar, remove the door checker mounting
bolt (A).
2. Detach the clips (B, C, D), then remove the door weatherstrip (E).
3. Install the weatherstrip in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Make sure the weatherstrip is installed in the holder (F) securely.
 Apply medium strength liquid thread lock to door checker mounting bolt before installation.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
08/08/21 14:59:03 61SNR030_200_0018
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connector is plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
20-1920-19
Rear Door Outer Handle
Replacement
A B
62 mm (2.44 in.) A
B
C
D C
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connector is plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Detach the harness clip (A), and disconnect the power door lock actuator connector (B).
4. Remove the plug caps (C), then remove the plastic cover (D), as needed.
5. Remove the latch mounting screws, then lower the latch (see step 4 on page 20-21).
6. Detach the rod fastener (A).
(cont’d)
08/08/21 14:59:06 61SNR030_200_0021
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-2120-21
Rear Door Latch Replacement
Fastener Locations :Screw,3
A:Screw,1 B
A
A
A
6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft) 6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft)C
B
11. Install the handle in the reverse order of removal, and note these items:
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on page 20-19).
4. Remove the screws (A, B) securing the latch (C), then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer handle (see step 7 on page 20-20).
(cont’d)
08/08/21 14:59:07 61SNR030_200_0023
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-2120-21
Rear Door Latch Replacement
Fastener Locations :Screw,3
A:Screw,1 B
A
A
A
6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft) 6x1.0mm
6N·m
(0.6 kgf·m, 4 lbf·ft)C
B
11. Install the handle in the reverse order of removal, and note these items:
 Make sure the door locks and opens properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel (see page 20-17).
3. Remove the plastic cover, as needed (see step 4 on page 20-19).
4. Remove the screws (A, B) securing the latch (C), then lower it.
5. Detach the rod fastener (see step 6 on page 20-19).
6. Disconnect the outer handle rod from the outer handle (see step 7 on page 20-20).
(cont’d)
08/08/21 14:59:07 61SNR030_200_0023
ProCarManuals.com
DYNOMITE -2009-