differential ACURA CSX 2006 Service Owner's Manual

Î
ÎÎ
13-103
D
E B
C
F A
A B M
B
A
12. Apply tape to the mainshaft splines to protect the seal, then remove the mainshaft assembly (A) and
the countershaft assembly (B) with the shift fork
assembly (C) from the clutch housing (D).
13. Remove the 28 mm spring washer (E) and the 28 mm washer (F).
14. Remove the differential assembly (A) and the magnet (B). 15. Remove the oil gutter plate (A), the 72 mm shim (B),
and oil guide plate M.
08/08/21 14:47:57 61SNR030_130_0105
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'

!)
72 mm Shim (cont’d)
Type Part Number Thickness
13-13313-133
Transmission Reassembly
B
A
C
A F
G
B D
E
H
AP 23972-PPP-J00 1.83 mm (0.072 in.)
AQ 23973- PPP-J00 1.86 mm (0.073 in.)
AR 23974- PPP-J00 1.89 mm (0.074 in.)
AS 23975- PPP-J00 1.92 mm (0.076 in.)
AT 23976- PPP-J00 1.95 mm (0.077 in.)
AV 23977- PPP-J00 1.98 mm (0.078 in.)
AW 23978- PPP-J00 2.01 mm (0.079 in.)
AX 23979- PPP-J00 2.04 mm (0.080 in.)
AY 23980- PPP-J00 2.07 mm (0.081 in.)
AZ 23981- PPP-J00 2.10 mm (0.083 in.)
BA 23982- PPP-J00 2.13 mm (0.084 in.)
BB 23983- PPP-J00 2.16 mm (0.085 in.)
BC 23984- PPP-J00 2.19 mm (0.086 in.)
BD 23985- PPP-J00 2.22 mm (0.087 in.)
BE 23986- PPP-J00 2.25 mm (0.089 in.) NOTE:
 Prior to reassembling, clean all the parts in solvent, dry them, and apply MTF to any contact surfaces.
 Place the clutch housing on two pieces of wood thick enough to keep the mainshaft from hitting the
workbench.
1. Install the magnet (A) and the differential assembly (B).
NOTE: Clean the magnet anytime the transmission
is disassembled.
2. Install the 28 mm spring washer (A) and the 28 mm washer (B) over the ball bearing (C).
NOTE: Install the spring washer in the direction
shown.
3. Apply tape to the mainshaft splines (D) to protect the seal. Install the mainshaft assembly (E), the
countershaft assembly (F), and the shift fork
assembly (G) into the clutch housing (H), as an
assembly.
(cont’d)
08/08/22 16:37:21 61SNR030_130_0135
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'

!)
72 mm Shim (cont’d)
Type Part Number Thickness
13-13313-133
Transmission Reassembly
B
A
C
A F
G
B D
E
H
AP 23972-PPP-J00 1.83 mm (0.072 in.)
AQ 23973- PPP-J00 1.86 mm (0.073 in.)
AR 23974- PPP-J00 1.89 mm (0.074 in.)
AS 23975- PPP-J00 1.92 mm (0.076 in.)
AT 23976- PPP-J00 1.95 mm (0.077 in.)
AV 23977- PPP-J00 1.98 mm (0.078 in.)
AW 23978- PPP-J00 2.01 mm (0.079 in.)
AX 23979- PPP-J00 2.04 mm (0.080 in.)
AY 23980- PPP-J00 2.07 mm (0.081 in.)
AZ 23981- PPP-J00 2.10 mm (0.083 in.)
BA 23982- PPP-J00 2.13 mm (0.084 in.)
BB 23983- PPP-J00 2.16 mm (0.085 in.)
BC 23984- PPP-J00 2.19 mm (0.086 in.)
BD 23985- PPP-J00 2.22 mm (0.087 in.)
BE 23986- PPP-J00 2.25 mm (0.089 in.) NOTE:
 Prior to reassembling, clean all the parts in solvent, dry them, and apply MTF to any contact surfaces.
 Place the clutch housing on two pieces of wood thick enough to keep the mainshaft from hitting the
workbench.
1. Install the magnet (A) and the differential assembly (B).
NOTE: Clean the magnet anytime the transmission
is disassembled.
2. Install the 28 mm spring washer (A) and the 28 mm washer (B) over the ball bearing (C).
NOTE: Install the spring washer in the direction
shown.
3. Apply tape to the mainshaft splines (D) to protect the seal. Install the mainshaft assembly (E), the
countershaft assembly (F), and the shift fork
assembly (G) into the clutch housing (H), as an
assembly.
(cont’d)
08/08/22 16:37:21 61SNR030_130_0135
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
13-139
M/T Differential
Component Location Index
CARRIER BEARING
FINAL DRIVEN GEARDIFFERENTIAL CARRIER
CARRIER BEARING
SHIM, 80 mm
OIL SEAL
OIL SEAL
Replacement, page 13-140
Replacement, page 13-140Replacement, page 13-140
Replacement, page 13-140
Differential Thrust Clearance Adjustment, page 13-142
Replacement, page 13-141
Replacement, page 13-141
08/08/21 14:48:56 61SNR030_130_0141
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
 )
 Î
Î
(#'


 ) Special Tools Required
13-14013-140 M/T Differential
Differential Carrier, Final Driven
Gear Replacement
Carrier Bearing Replacement
A
B 11x1.0mm(10)
121N·m(12.3kgf·m,89lbf·ft)
B
A
B
A
1. Loosen the bolts in a crisscross pattern in several steps, then remove the bolts and the final driven
gear (A) from the differential carrier (B).
2. Install the final driven gear with the chamfer on the inside diameter facing the carrier. Tighten the bolts
in a crisscross pattern in several steps. Inner driver handle, 40 mm 07746-0030100
1. Check the carrier bearings for wear and rough rotation. If they rotate smoothly and their rollers
show no signs of wear, the bearings are OK.
2. Remove the carrier bearings (A) with a commercially available bearing puller (B).
08/08/21 14:48:56 61SNR030_130_0142
ProCarManuals.com
DYNOMITE -2009-

Î
Î

(#'

 ) Special Tools Required
13-14113-141
Oil Seal Replacement
B
07746-0030100
C
A
B
07746-0030100
C
A A
B
A
B
3. Install new bearings (A) on with the 40 mm inner driver handle (B) and a press. Press on each
bearing until it bottoms. There should be no
clearance between the bearings and the carrier.
NOTE: Place the seal (C) part of the bearing
towards the outside of the differential, and install it.  Oil seal driver attachment 07NAD-P20A100
 Driver handle, 15 x 135L 07749-0010000
1. Remove the oil seal (A) from the transmission housing (B).
2. Remove the oil seal (A) from the clutch housing (B).
(cont’d)
08/08/21 14:48:57 61SNR030_130_0143
ProCarManuals.com
DYNOMITE -2009-

Î
Î

(#'

 ) Special Tools Required
13-14113-141
Oil Seal Replacement
B
07746-0030100
C
A
B
07746-0030100
C
A A
B
A
B
3. Install new bearings (A) on with the 40 mm inner driver handle (B) and a press. Press on each
bearing until it bottoms. There should be no
clearance between the bearings and the carrier.
NOTE: Place the seal (C) part of the bearing
towards the outside of the differential, and install it.  Oil seal driver attachment 07NAD-P20A100
 Driver handle, 15 x 135L 07749-0010000
1. Remove the oil seal (A) from the transmission housing (B).
2. Remove the oil seal (A) from the clutch housing (B).
(cont’d)
08/08/21 14:48:57 61SNR030_130_0143
ProCarManuals.com
DYNOMITE -2009-



Î
(#'
") Special Tools Required
13-14213-142 M/T Differential
Oil Seal Replacement (cont’d) Differential Thrust Clearance
Adjustment
A
07749-0010000
B
07NAD-P20A100
A
07749-0010000 B
07NAD-P20A100
3. Install a new oil seal flush with the transmission housing with the 15 x 135L driver handle (A) and
the oil seal driver attachment (B).
4. Install a new oil seal flush with the clutch housing with the 15 x 135L driver handle (A) and the oil seal
driver attachment (B). Inner driver handle, 40 mm 07746-0030100
1. If you removed the 80 mm shim from the transmission housing reinstall is the same sized
shim.
2. Install the differential assembly into the clutch housing.
08/08/21 14:48:58 61SNR030_130_0144
ProCarManuals.com
DYNOMITE -2009-



Î
(#'
") Special Tools Required
13-14213-142 M/T Differential
Oil Seal Replacement (cont’d) Differential Thrust Clearance
Adjustment
A
07749-0010000
B
07NAD-P20A100
A
07749-0010000 B
07NAD-P20A100
3. Install a new oil seal flush with the transmission housing with the 15 x 135L driver handle (A) and
the oil seal driver attachment (B).
4. Install a new oil seal flush with the clutch housing with the 15 x 135L driver handle (A) and the oil seal
driver attachment (B). Inner driver handle, 40 mm 07746-0030100
1. If you removed the 80 mm shim from the transmission housing reinstall is the same sized
shim.
2. Install the differential assembly into the clutch housing.
08/08/21 14:48:58 61SNR030_130_0144
ProCarManuals.com
DYNOMITE -2009-

Î
Îµµ
Specified Torque:
8x1.25mm
27 N·m (2.8 kgf·m, 20 lbf·ft)
Standard: 0 0.10 mm (0 0.039 in.) 80 mm Shim
Type Part Number Thickness
13-143
00746-0030100
3. Install the transmission housing onto the clutchhousing, then tighten the 8 mm flange bolts in a
crisscross pattern in several steps (see step 14 on
page 13-136).
4. Use the 40 mm inner driver handle to bottom the differential assembly in the clutch housing.
5. Measure the clearance between the 80 mm shim and the bearing outer race in transmission housing. 6. If the clearance exceeds the standard, select a new
80 mm shim from the following table. If the
clearance measured in step 5 is within the standard,
go to step 9.
A 41441-PL3-B00 1.00 mm (0.0394 in.)B 41442-PL3-B00 1.10 mm (0.0433 in.)
C 41443-PL3-B00 1.20 mm (0.0472 in.)
D 41444-PL3-B00 1.30 mm (0.0512 in.) E 41445-PL3-B00 1.40 mm (0.0551 in.)F 41446-PL3-B00 1.50 mm (0.0591 in.)
G 41447-PL3-B00 1.60 mm (0.0630 in.) H 41448-PL3-B00 1.70 mm (0.0669 in.) J 41449-PL3-B00 1.80 mm (0.0709 in.)
K 41450-PL3-B00 1.05 mm (0.0413 in.) L 41451-PL3-B00 1.15 mm (0.0453 in.)
M 41452-PL3-B00 1.25 mm (0.0492 in.) N 41453-PL3-B00 1.35 mm (0.0531 in.) P 41454-PL3-B00 1.45 mm (0.0571 in.)
Q 41455-PL3-B00 1.55 mm (0.0610 in.) R 41456-PL3-B00 1.65 mm (0.0650 in.)
S 41457-PL3-B00 1.75 mm (0.0689 in.)
7. Remove the bolts and transmission housing.
8. Replace the thrust shim selected in step 6, then recheck the clearance.
9. Reinstall the transmission housing.
08/08/21 14:48:58 61SNR030_130_0145
ProCarManuals.com
DYNOMITE -2009-