fuse ACURA CSX 2006 Service Owner's Manual

Î
(#'

)
10-23
Fan Controls
Component Location Index
FAN CONTROL RELAY
UNDER-HOOD FUSE/RELAY BOX
RADIATOR FAN RELAY
A/C CONDENSER FAN ASSEMBLY RADIATOR FAN ASSEMBLY ENGINE COOLANT TEMPERATURE
(ECT) SENSOR 2ENGINE COOLANT TEMPERATURE
(ECT) SENSOR 1
A/C CONDENSER FAN RELAY
Test, page 22-70
Test, page 22-70
Motor Test, page 10-5
Replacement, page 10-19 Motor Test, page 10-5
Replacement, page 10-19 Replacement, page 11-225Replacement, page 11-225
Test, page 22-70
08/08/21 14:40:31 61SNR030_100_0023
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
10-25
Circuit Diagram
ECT2
SG6
SG2
ECT1 FANH
FANL
SUBRLY IG2HOTinON(II)
PNK
5V No. 15 (7.5 A)
A21
PUR
ECM/PCM
2G301
BLK
2
1
No. 11 (15 A)
(10 A) No. 36
B23
RED/WHT GRN/BLK B33
BLU GRY
BRN
A33
BLK GRN A9 IGNITION SWITCH
IG2
BAT
RED
3
2 5
4 1
A4
A5 13
4
2
1 2 23 4
1 No. 2 (50 A)
BLK
UNDER-HOOD FUSE/RELAY BOX
BATTERY
G301No. 1 (100 A)
No. 6 (20 A)
A/C
CONDENSER
FAN RELAY
ENGINE COOLANT
TEMPERATURE
(ECT) SENSOR 1
A/C
CONDENSER
FAN MOTOR
FAN
CONTROL
RELAY
RADIATOR
FAN
MOTOR
ENGINE COOLANT
TEMPERATURE
(ECT) SENSOR 2 RADIATOR
FAN
RELAY
PGM-FI
SUB RELAY
H1
3 4
ORN
G12
D1
F16
F7
F2
F12
F14
F1
F11 No. 7 (20 A)
21
1 UNDER-DASH
FUSE/RELAY
BOX
BRN
WHT
43
12 C3
08/08/21 14:40:32 61SNR030_100_0025
ProCarManuals.com
DYNOMITE -2009-

Î
Î
Î
(#'


)
µ
µ
µ
µ
µ
µ µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
10-26Fan Controls
Radiator Fan High Speed Circuit Troubleshooting
RADIATOR FAN RELAY 4P SOCKET
FAN CONTROL RELAY 5P SOCKET
JUMPER WIRE
RADIATOR FAN RELAY 4P SOCKET JUMPER WIRE
1. Check the No. 7 (20 A) fuse in the under-hood fuse/relay box and the No. 36 (10 A) fuse in the under-
dash fuse/relay box.
Reinstall the fuse(s), then go to step 2.
Replace the fuse(s), and recheck. If the fuse
continues to blow, locate and repair the short in the
circuit between the under-hood fuse/relay box and
the radiator fan motor, or between the under-dash
fuse/relay box connector terminal G12, the under-
hood fuse/relay box and the engine control module
(ECM)/powertrain control module (PCM).
2. Remove the radiator fan relay and the fan control relay from the under-hood fuse/relay box, and test
them (see page 22-70).
Go to step 3.
Replace the radiator fan relay and/or fan
control relay.
3. Measure the voltage between the radiator fan relay 4P socket terminal No. 1 and body ground.
Go to step 4.
Replace the under-hood fuse/relay box. 4. Connect fan control relay 5P socket terminals No. 1
andNo.2withajumperwire.
5. Connect radiator fan relay 4P socket terminals No. 1 and No. 2 with a jumper wire.
Go to step 10.
Go to step 6.
Terminal side of female terminals Terminal side of female terminals
Terminal side of female terminals
Ar e t he f uses OK ? Ar e t he r el ay s OK ?
Is there battery voltage? Does t he r ad i at or f an r un at hi gh speed ?
08/08/21 14:40:32 61SNR030_100_0026
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
µ
µ µ
µ
YES
NO YES
NO
10-28Fan Controls
Radiator Fan High Speed Circuit Troubleshooting (cont’d)
FAN CONTROL RELAY 5P SOCKET
RADIATOR FAN MOTOR 2P CONNECTOR RED RADIATOR FAN RELAY 4P SOCKET
9. Check for continuity between fan control relay 5P
socket terminal No. 1 and radiator fan motor 2P
connector terminal No. 1.
Check for poor connections or loose
terminals at the under-hood fuse/relay box, the
radiator fan motor, and body ground (G 301), then
go to step 1.
Repair open in the wire between fan control
relay 5P socket terminal No. 1 and radiator fan
motor 2P connector terminal No. 1. 10. Turn the ignition switch to ON (II).
11. Measure the voltage between radiator fan relay 4P
socket terminal No. 3 and body ground.
Go to step 12.
Repair open in the wire between the under-
dash fuse/relay box and the under-hood fuse/relay
box.
12. Turn the ignition switch to LOCK (0).
13. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
14. Turn the ignition switch to ON (II).
15. Make sure the HDS communicates with the vehicle and the ECM/PCM. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
16. Jump the SCS line with the HDS, then turn the ignition switch to LOCK (0).
NOTE: This step must be done to protect the ECM/
PCMfromdamage.
17. Disconnect ECM/PCM connector A (44P).
Terminal side of female termianls
Wire side of female terminals Terminal side of female terminals
Is there continuity?
Is there battery voltage?
08/08/21 14:40:33 61SNR030_100_0028
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
µ
µ µ
µ
YES
NO YES
NO
10-29
RADIATOR FAN RELAY 4P SOCKET
ECM/PCM CONNECTOR A (44P) PUR FAN CONTROL RELAY 5P SOCKET
18. Check for continuity between radiator fan relay 4P
socket terminal No. 4 and ECM/PCM connector
terminal A4.
Go to step 19.
Repair open in the wire between radiator fan
relay 4P socket terminal No. 4 and ECM/PCM
connector terminal A4. 19. Turn the ignition switch to ON (II).
20. Measure the voltage between fan motor control
relay 5P socket terminal No. 5 and body ground.
Go to step 21.
Repair open in the wire between the under-
dash fuse/relay box and the under-hood fuse/relay
box.
21. Turn the ignition switch to LOCK (0).
(cont’d)
Terminal side of female terminals
Terminal side of female terminals
Terminal side of female terminals
Is there continuity?Is there battery voltage?
08/08/21 14:40:34 61SNR030_100_0029
ProCarManuals.com
DYNOMITE -2009-


HDS Clear Command
Scan Tool Clear Command
DTC ClearECM/PCM Reset
CKP Pattern Clear/CKP Pattern Learn
Clear/Learn Procedure (with the HDS)
11-4Fuel and Emissions Systems
General Troubleshooting Information (cont’d)
A
The ECM/PCM stores various specific data to correct the
system even if there is no electrical power, such as
when the battery negative terminal or the No. 19
FI MAIN (15 A) fuse is disconnected. Stored data based
on failed parts should be cleared by using the CLEAR
COMMAND of the HDS, if parts are replaced.
The HDS has three kinds of clear commands to meet
this purpose. They are DTC clear, ECM/PCM reset, and
CKP pattern clear. DTC clear command erases all stored
DTC codes, freeze data, on-board snapshot, and
readiness codes. This must be done with the HDS after
reproducing the DTC during troubleshooting.
The ECM/PCM reset command erases all stored DTC
codes, freeze data, on-board snapshot, readiness codes,
and all specific data to correct the system except CKP
pattern. If the CKP pattern data in the ECM/PCM was
cleared, you must do the CKP pattern learn procedure.
The CKP pattern clear command erases only CKP
pattern data. This command is for repair of a misfire or
the CKP sensor.
If you are using a generic scan tool to clear commands,
be aware that there is only one setting for clearing the
ECM/PCM, and it clears all commands at the same time
(CKP pattern learn, idle learn, readiness codes, freeze
data, on-board snapshot, and DTCs). After you clear all
commands, you then need to do these procedures, in
this order: ECM/PCM idle learn procedure (see page
11-310); CKP pattern learn procedure;
Test-drive to set readiness codes to complete (see page
11-69).
1. Clear the DTC with the HDS while the engine is stopped.
2. Turn the ignition switch to LOCK (0).
3. Turn the ignition switch to ON (II), and wait 30 seconds.
4. Turn the ignition switch to LOCK (0), and disconnect the HDS from the DLC. 1. Reset the ECM/PCM with the HDS while the engine
is stopped.
2. Turn the ignition switch to LOCK (0).
3. Turn the ignition switch to ON (II), and wait 30 seconds.
4. Turn the ignition switch to LOCK (0), and disconnect the HDS from the DLC.
5. Do the ECM/PCM idle learn procedure (see page 11-310).
1. Connect the HDS to the data link connector (DLC) (A) located under the driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the ECM/ PCM and other vehicle systems. If it doesn’t, go to
the DLC circuit troubleshooting (see page 11-204).
4. Select CRANK PATTERN in the ADJUSTMENT MENU with the HDS.
5. Select CRANK PATTERN LEAR NING with the HDS,
and follow the screen prompts.
08/08/21 14:12:32 61SNR030_110_0004
ProCarManuals.com
DYNOMITE -2009-

ØÚÓ



Î
How to Troubleshoot Circuits at the ECM/
PCM Connectors
11-6 Fuel and Emissions Systems
General Troubleshooting Information (cont’d)
A
D E
B
A
C A
B D
C
A
NOTE: The ECM/PCM overwrites data and monitors the
EVAP system for about 30 minutes after the ignition
switch is turned to LOCK (0) or ACC (I). Jumping the
SCS line after turning the ignition switch to LOCK (0) or
ACC (I) cancels this function. Disconnecting the ECM/
PCM during this function, without jumping the SCS line
first, can damage the ECM/PCM.
1. Make sure the ignition switch is turned to LOCK (0), then jump the SCS line with the HDS.
2. Remove the cover (A).
3. Lift up the under-hood fuse/relay box (D).
4. Remove the coolant reservoir (E). Disconnect ECM/ PCM connectors A, B, and C, and probe the
terminals from the terminal side of the connectors.
NOTE: ECM/PCM connectors A, B, and C have
symbols (A= , B= , C= ) embosed on them for
identification. 5. When diagnosis/troubleshooting is done at the
ECM/PCM connector, use the terminal test port (A)
above the terminal you need to check.
6. Connect one side of the patch cord’s terminals (A) to a commercially available digital multimeter (B),
and connect the other side cord’s terminals (C) to a
commercially available banana jack (Pomona
Electronics Tool No. 3563 or equivalent) (D).
7. Gently contact the pin probe (male) at the terminal test port from the terminal side. Do not force the
tips into the terminals.
 For accurate results, always use the pin probe (male).
 To prevent damage to the c onnector
terminals, do not insert test equipment
probes, paper clips, or other substitutes as
they can damage the terminals. Damaged
terminals cause a poor connection and an
incorrect measurement.
 Do not puncture the insulation on a wire. Punctures can cause poor or intermittent
electrical connections.
08/08/21 14:12:34 61SNR030_110_0006
ProCarManuals.com
DYNOMITE -2009-

Î
´
ECM/PCM Electrical Connections
11-16Fuel and Emissions Systems
System Description (cont’d)
IGNITION
SWITCH
IG1
ST B
IG2
IG1 HOT in ON (II)
and START (III) IGNITION COIL
RELAY
ELD PGM-FI MAIN
RELAY 2 (FUEL PUMP)P
FUEL PUMP
PGM-FI MAIN
RELAY 1
BATTERY A/C CONDENSER
FAN RELAYRADIATOR
FAN RELAY
A/C COMPRESSOR
CLUTCH RELAY
To
COOLING
FAN CONTROL
RELAY E
A8 IGPC36 IG1
A14 ACC
A5 FANH A23 ELD
A4 FANL GF
C
B
D
A
PG1 B36PG2 B1
MRLY A6
IMOFPR A15
SUBRLY A21
ETCSRLY A20 STARTER CUT
RELAY (ST CUT)
PGMETCS C2 PGM-FI
SUBRELAY
ETCS CONTROL
RELAY
I
IG1ETCS C1
ECM/PCM
CLUTCH
INTERLOCK
SWITCH
H
J*2
*1
T
*3
*1: A/T
*2: M/T
*3: K20Z3 engine
UNDER-HOOD
FUSE/RELAY BOX:
No. 1 MAIN FUSE (100 A)
No.19FIMAIN(15A)
No. 2 IG MAIN (50 A)
No. 23 BACK UP (10 A)
No. 12 STOP & HORN
(15 A) No. 18 IG COIL (15 A)
UNDER-DASH
FUSE/RELAY BOX: No. 3 ALTERNATOR
(10 A) No. 2 FUEL PUMP (15 A)
No. 36 IG2 HAC (A/C)
(10 A)
UNDER-HOOD
FUSE/RELAY BOX: No.15OILLVL(7.5A)
No. 11 FI SUB (15 A)
No. 21 DBW (THROTTLE
ACTUATOR CONTROL) (15 A)
08/08/21 14:12:37 61SNR030_110_0016
ProCarManuals.com
DYNOMITE -2009-




VTEC/VTC
System Diagram
Camshaft Position (CMP) Sensor A
11-39
VTC
RETARD
CHAMBERFrom No. 3
ALTERNATOR
(10 A) FUSE
VARIOUS
SENSORS
ECM/PCM
CMP SENSOR A
INTAKE
CAMSHAFT
VTC
ADVANCE
CHAMBER ADVANCE
RETARD
VANE
VTC ACTUATOR VANE
HOUSING
From
OIL PUMP
VTC OIL CONTROL
SOLENOID VALVE
SPOOL
VALVE
ROCKER ARM
OIL CONTROL
SOLENOID ROCKER
ARM OIL
PRESSURE
SWITCH BLK
BLK GRN/YEL
BLU/BLK BLK/YEL
BLU/WHT BLU/WHT YEL
BRN/YEL
BLK
BRN/YEL
VTC STRAINERO-RING
MAGNET
TERMINAL
DRAIN
DRAIN
CMP sensor A detects camshaft angle position for the VTC system.
(cont’d)
08/08/21 14:13:41 61SNR030_110_0039
ProCarManuals.com
DYNOMITE -2009-

Î

Evaporative Emission (EVAP) Control Diagram
11-45
ATMOSPHERE
ATMOSPHERE
FUEL FILL
CAP FUEL TANK VAPOR
RECIRCULATION
TUBE
FUEL TANK VAPOR
CONTROL VALVE
VARIOUS
SENSORS
FUEL TANK FTP SENSOR
EVAP CANISTER
VENT SHUT VALVE
PUR
LT GRN
ECM/PCM BLK
YEL
YEL/BLU
BLK/YEL RED
BLU BLK
LT GRN
From
No. 3
ALTERNATOR
(10 A) FUSE
From
PGM-FI
SUBRELAY
EVAP
CANISTER
EVAP CANISTER
PURGE VALVE ATMOSPHERE
The EVAP controls minimize the amount of fuel vapor escaping into the atmosphere. Vapor from the fuel tank is
temporarily stored in the EVAP canister until it can be purged from the canister into the engine and burned.
The EVAP canister is purged by drawing fresh air through it and into a port on the intake manifold.
The purging vacuum is controlled by the EVAP canister purge valve, which operates whenever engine coolant
temperature is above 60 °C (140 °F).
(cont’d)
* : This illustration shows K20Z2 engine
08/08/21 14:13:44 61SNR030_110_0045
ProCarManuals.com
DYNOMITE -2009-