valve lash ACURA CSX 2006 Service Owner's Manual


14-218Automatic Transmission
Shift Solenoid Valve and Shift Solenoid Wire Harness Replacement (cont’d)
F
6x1.0mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
A
D E
FB
F
C
G
H
G G
G
G
10. Remove the mounting bolts (F), then hold the shift
solenoid valve body and remove the shift solenoid
valves. Do not hold the connector to remove the
shift solenoid valve.
11. Install new O-rings (two O-rings per solenoid valve) (G) on the reused solenoid valve.
NOTE: A new solenoid valve comes with new
O-rings. If you install a new solenoid valve, use the
O-rings provided with it.
12. Install shift solenoid valves C (brown connector), D (black connector), and E (black connector) by
holding the shift solenoid valve body; make sure
the mounting bracket contacts the servo body.
NOTE: Do not hold the shift solenoid valve
connector to install the shift solenoid valve. Be sure
to hold the shift solenoid valve body.
13. Install shift solenoid valve B (brown connector) by holding the shift solenoid valve body; make sure
the mounting bracket contacts the bracket of shift
solenoid valve E. 14. Install shift solenoid valve A (brown connector) by
holding the shift solenoid valve body; make sure
the mounting bracket contacts the bracket of shift
solenoid valve D.
NOTE: Do not install shift solenoid valves A and B
before installing shift solenoid valve D and E. If
shift solenoid valve A or B is installed before
installing shift solenoid valve D or E, it may
damage to hydraulic control system.
15. Connect YEL, WHT, and WHT harnesses terminal (H) to shift solenoid valve D. The ATF temperature
sensor is installed in the connector.
16. Connect the shift solenoid valve connectors:  BLU wire to shift solenoid valve A
 ORN wire to shift solenoid valve B
 GRN wire to shift solenoid valve C
 RED wire to shift solenoid valve E
17. Install a new gasket, the dowel pins, and the shift solenoid valve cover.
18. Check the connector for rust, dirt, or oil, then connect the connector securely.
19. Refill the transmission with ATF (see step 5 on page 14-232).
20. Install the battery base, the battery tray, and the resonator.
21. Install the air cleaner assembly (see page 11-345) and the intake air duct (see page 11-348).
22. Do the battery installation procedure (see page 22-69).
23. Install the splash shield.
08/08/21 14:46:45 61SNR030_140_0220
ProCarManuals.com
DYNOMITE -2009-

Î
Î

(#'




)

14-229
ATF Temperature Sensor Test/Replacement
A
18x1.5mm
49 N·m
(5.0 kgf·m, 36 lbf·ft) B A
B
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
1. Raise the vehicle on a lift, or apply the parkingbrake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
2. Remove the splash shield.
3. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
4. Reinstall the drain plug with a new sealing washer (B).
5. Do the battery removal procedure (see page 22-69).
6. Remove the intake air duct (see page 11-348) and the air cleaner assembly (see page 11-345).
7. Remove the battery tray, the battery base, and the resonator. 8. Remove the shift solenoid valve cover (A), the
dowel pins (B), and the gasket (C).
9. Disconnect the shift solenoid wire harness connector, and remove it from the transmission
housing.
(cont’d)
Replace. Replace.
08/08/21 14:46:51 61SNR030_140_0231
ProCarManuals.com
DYNOMITE -2009-

Î
µStandard: 50 25 k
14-230Automatic Transmission
ATF Temperature Sensor Test/Replacement (cont’d)
C
D
B
A
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) E
G F
10. Measure the ATF temperature sensor resistance between shift solenoid wire harness connector
terminals No. 6 and No. 7.
 If the resistance is within the standard, install the shift solenoid wire harness and a new O-ring in
the transmission, then go to step 13.
 If the resistance is out of standard, go to step 11.
11. Disconnect the connectors from the shift solenoid valves, and replace the ATF temperature sensor/
shift solenoid harness assembly (F) and the O-ring
(G) with new ones.
NOTE: The ATF temperature sensor is not available
separately from the shift solenoid wire harness.
12. Connect the shift solenoid valve connectors:  BLU wire to shift solenoid valve A.
 ORN wire to shift solenoid valve B.
 GRN wire to shift solenoid valve C.
 YEL, WHT, and WHT wire connector to shiftsolenoid valve D.
 RED wire to shift solenoid valve E.
13. Install a new gasket, the dowel pins, and the shift solenoid valve cover.
14. Check the connector for rust, dirt, or oil, clean or repair if necessary, then connect the connector
securely. 15. Refill the transmission with ATF (see step 5 on page
14-232).
16. Install the battery tray, the battery base, and the resonator.
17. Install the air cleaner assembly (see page 11-345) and the intake air duct (see page 11-348).
18. Do the battery installation procedure (see page 22-69).
19. Install the splash shield.
Replace.
08/08/21 14:46:51 61SNR030_140_0232
ProCarManuals.com
DYNOMITE -2009-