belt ACURA CSX 2006 Service Owner's Guide





6-65
A
B6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
B
A A
B
19. Connect the positive crankcase ventilation (PCV)hose (A) (K20Z2 engine) and install the ground
cable (B).
20. Connect the fuel feed hose (A) (see page 11-331), then install the quick-connect fitting cover (B). 21. Connect the evaporative emission (EVAP) canister
hose (A) and the brake booster vacuum hose (B).
22. Install the exhaust manifold (see page 9-11).
23. Install the intake manifold:  K20Z2 engine (see page 9-4)
 K20Z3 engine (see page 9-9)
24. Install the drive belt (see page 4-31).
25. Install the air cleaner assembly (see page 11-345).
26. After installation, check that all tubes, hoses and connectors are installed correctly.
27. Inspect for fuel leaks. Turn the ignition switch to ON (II) (do not operate the starter) so that the fuel
pump runs for about 2 seconds and pressurizes the
fuel line. Repeat this operation three times, then
check for fuel leakage at any point in the fuel line.
(cont’d)
08/08/21 14:28:44 61SNR030_060_0065
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
7-11
Oil Pan Removal
1. If the engine is already out of the vehicle, go to step 18.
2. Raise the vehicle on the lift.
3. Drain the engine oil (see page 8-10).
4. Remove the front wheels.
5. Remove the splash shield (see step 25 on page 5-5).
6. Separate the stabilizer links (see page 18-25).
7. Separate the knuckles from the lower arms (see step 6 on page 18-21).
8. Remove the steering gearbox bracket. Remove the steering gearbox mounting bolt, the stiffener
mounting bolt, and the stiffener (see step 36 on
page 5-6).
9. Remove the steering gearbox mounting bolt, the stiffener mounting bolt, and the stiffener. Remove
the harness clamp from the front subframe (see
step 38 on page 5-6).
10. A/T model: Remove the bolt securing the automatic transmission fluid (ATF) filter.
11. Install the front leg assembly, the hook, and the wing nut to an A and Reds engine support hanger
(AAR-T1256) onto the 2006 Civic engine hanger
(VSB02C000025). Carefully position the engine
hanger on the vehicle, and attach the hook to the
slotted hole in the support eyelet. Tighten the wing
nut by hand to lift and support the engine/
transmission (see step 47 on page 5-8). 12. Remove the lower torque rod (see step 49 on page
5-8).
13. M/T model: Remove the front mount mounting bolt (see step 50 on page 5-9).
14. Make the appropriate reference line at both sides of the front subframe that line up with the edges on
the body (see step 51 on page 5-9).
15. Loosen the mid-stiffener mounting bolts on both sides(seestep52onpage5-9).
16. Attach the front subframe adapter (VSB02C000016) to the front subframe, and hang the belt of the front
subframe adapter over the front of the subframe.
Secure the belt with its stop, then tighten the wing
nut (see step 53 on page 5-9).
17. Remove the front subframe (see step 55 on page 5-10).
18. Remove the lower torque rod bracket.
(cont’d)
08/08/21 14:32:34 61SNR030_070_0011
ProCarManuals.com
DYNOMITE -2009-



7-30Engine Block
Oil Pan Installation (cont’d)
B
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
12x1.25mm
64N·m(6.5kgf·m,47lbf·ft)
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) 12 x 1.25 mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
7. K20Z3 engine: Install the transmission mounting
bolts (A) and the clutch cover (B).
8. A/T model: Install the shift cable cover. 9. Install the lower torque rod bracket.
10. If the engine is still in the vehicle, do the following steps.
11. Attach the front subframe adapter (VSB02C000016) to the front subframe, and hang the belt of the front
subframe adapter over the front of the subframe.
Secure the belt with its stop, then tighten the wing
nut (see step 53 on page 5-9).
12. Line up the slots in the front subframe adapter arms with the bolt holes on the jack base, then
securely attach them with four bolts. Lift the front
subframe up to the body.
13. Loosely install the new front subframe mounting bolts (see step 17 on page 5-17).
14. Align all reference marks on the front subframe with the edges of the body, then tighten the bolts
on the front subframe to the specified torque (see
step 18 on page 5-18).
15. Remove the jack and the front subframe adapter.
16. Tighten the new mid-stiffener mounting bolts on both sides (see step 20 on page 5-18).
17. Lower the vehicle on the lift.
18. Loosen the upper torque rod mounting bolt (see step 5 on page 5-15).
Replace.
08/08/21 14:33:12 61SNR030_070_0030
ProCarManuals.com
DYNOMITE -2009-


(#'


") 
(#'


 )
K20Z2 engine
10-610-6 Cooling System
Water Pump Inspection
Water Pump Replacement
A
A
B
A
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
1. Remove the drive belt (see page 4-31).
2. Turn the water pump pulley counterclockwise, and check that it turns freely and smoothly. If it does not
turn smoothly, replace the water pump (see page
10-6).
NOTE: When you check the water pump, you may
see a small amount of ‘‘weeping’’ from the bleed
holes (A). This is normal.
3. Install the drive belt (see page 4-31). 1. Remove the drive belt (see page 4-31).
2. Drain the engine coolant (see page 10-8).
3. Remove the drive belt auto-tensioner pulley
(see page 4-33).
4. Remove the crankshaft pulley (see page 6-16).
5. Remove the six bolts securing the water pump, then remove the water pump (A).
6. Inspect, and clean the O-ring groove and mating surface of the water passage.
7. Install the water pump with a new O-ring (B).
8. Clean up any spilled engine coolant.
9. Install the crankshaft pulley (see page 6-17).
10. Install the drive belt auto-tensioner pulley (see page 4-33).
11. Install the drive belt (see page 4-31).
12. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
08/08/21 14:39:57 61SNR030_100_0006
ProCarManuals.com
DYNOMITE -2009-


(#'


 )

(#'


")
K20Z3 engine
10-710-7
Coolant Check
A B
C
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) C A
B
1. Remove the drive belt (see page 4-31).
2. Drain the engine coolant (see page 10-8).
3. Remove the drive belt auto-tensioner pulley (see page 4-33).
4. Remove the crankshaft pulley (see page 6-16).
5. Remove the oil cooler joint pipe (A), then remove the seven bolts securing the water pump. Remove
the water pump (B).
6. Inspect, and clean the O-ring groove and mating surface of the water passage.
7. Install the water pump with new O-rings (C) and the oil cooler joint pipe.
8. Clean up any spilled engine coolant.
9. Install the crankshaft pulley (see page 6-17).
10. Install the drive belt auto-tensioner pulley (see page 4-33).
11. Install the drive belt (see page 4-31).
12. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8). 1. Check the coolant level in the coolant reservoir.
Make sure it is between the MAX mark (A) and MIN
mark (B).
2. If the coolant level in the coolant reservoir is at or below the MIN mark, add coolant to bring it up to
the MAX mark, then inspect the cooling system for
leaks.
08/08/21 14:39:58 61SNR030_100_0007
ProCarManuals.com
DYNOMITE -2009-


(#'


 )

(#'


")
K20Z3 engine
10-710-7
Coolant Check
A B
C
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) C A
B
1. Remove the drive belt (see page 4-31).
2. Drain the engine coolant (see page 10-8).
3. Remove the drive belt auto-tensioner pulley (see page 4-33).
4. Remove the crankshaft pulley (see page 6-16).
5. Remove the oil cooler joint pipe (A), then remove the seven bolts securing the water pump. Remove
the water pump (B).
6. Inspect, and clean the O-ring groove and mating surface of the water passage.
7. Install the water pump with new O-rings (C) and the oil cooler joint pipe.
8. Clean up any spilled engine coolant.
9. Install the crankshaft pulley (see page 6-17).
10. Install the drive belt auto-tensioner pulley (see page 4-33).
11. Install the drive belt (see page 4-31).
12. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8). 1. Check the coolant level in the coolant reservoir.
Make sure it is between the MAX mark (A) and MIN
mark (B).
2. If the coolant level in the coolant reservoir is at or below the MIN mark, add coolant to bring it up to
the MAX mark, then inspect the cooling system for
leaks.
08/08/21 14:39:58 61SNR030_100_0007
ProCarManuals.com
DYNOMITE -2009-




Î

13-12Manual Transmission
Transmission Removal (cont’d)
A
A
BB
A B
C VSB02C000016
A
AB
A
A
25. Remove the lower torque rod mounting bolt.
26. Remove the middle subframe mounting bolts (A).
27. Note the reference marks (A) on both sides of the
front subframe that lines up with the body (B). 28. Attach the front subframe adapter (VSB02C000016)
to the front subframe, and hang the belt (A) of the
subframe attachment over the front subframe, then
secure the belt with the stop (B).
29. Raise the jack, and line up the slots in the arms with the bolt holes on the corner of the jack base (C),
then attach them securely.
30. Remove the front subframe mounting bolts (A) and the front subframe (B).
NOTE: Suspend the steering gearbox with an
appropriate size wire.
08/08/21 14:44:24 61SNR030_130_0014
ProCarManuals.com
DYNOMITE -2009-





Î
Î
13-89
A
A BB
A B
C VSB02C000016
A
AB
A
A
25. Remove the lower torque rod mounting bolt.
26. Remove the middle subframe mounting bolts (A).
27. Note the reference marks (A) on both sides of the
front subframe that lines up with the body (B). 28. Attach the front subframe adapter (VSB02C000016)
to the front subframe, and hang the belt (A) of the
subframe attachment over the front subframe, then
secure the belt with the stop (B).
29. Raise the jack, and line up the slots in the arms with the bolt holes on the corner of the jack base (C),
then attach them securely.
30. Remove the front subframe mounting bolts (A) and the front subframe (B).
NOTE: Suspend the steering gearbox with an
appropriate size wire.
(cont’d)
08/08/21 14:47:24 61SNR030_130_0091
ProCarManuals.com
DYNOMITE -2009-



(#' )

S

pecial Tools RequiredB-Pillar Upper/Lower Trim
20-72 Interior Trim
Trim Removal/Installation - Pillar Areas (cont’d)
Fastener Locations
: Clip, 2(White)
A B
A
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Remove these items:  Front door sill trim (see page 20-66)
 Rear door sill trim (see page 20-67)
 Front door opening seal, as needed (see step 4on page 20-66)
 Rear door opening seal, as needed (see step 3 on page 20-68)
2. Slide the front seat fully forward. 3.

Remove the B-pillar lower trim (A).
–1 Pull the upper portion of the trim back to release the upper hooks (B).
–2 Detach the lower clips by pulling the bottom of thetrimbackbyhand.
4. Remove the front seat belt lower anchor (see page 24-4).
08/08/21 15:01:32 61SNR030_200_0074
ProCarManuals.com
DYNOMITE -2009-






20-73
A
B
A
Fastener Location :Clip,1(Pink)
BA
A
C A
B
C
A
B
5. Pull the bottom of the B-pillar upper trim (A) back
by hand to detach the lower hooks (B).
6. Detach the upper clip by pu lling the top of the
B-pillar upper trim (A). Pull the trim down to release
the upper hooks (B) from the side curtain airbag
B-pillar bracket (C). 7. Pass the front seat belt (A) lower anchor out
through a hole in the slider (B), then remove the
B-pillar upper trim (C).
8. Remove the slider (A) from the B-pillar upper trim
(B).
(cont’d)
08/08/21 15:01:33 61SNR030_200_0075
ProCarManuals.com
DYNOMITE -2009-