belt ACURA CSX 2006 Service Service Manual


Slider engagement with shoulder anchor adjuster
20-74 Interior Trim
Trim Removal/Installation - Pillar Areas (cont’d)
A
BC
D E
F A
F G
H IB
9. Install the trim in the reverse order of removal, and
note these items:
 If the clips (A) are damaged or stress-whitened, replace them with new ones.
 If the side curtain airbag has deployed, replace the B-pillar upper and lower trim and all clips on
the trim with new ones (see page 24-185).
 To prevent the side curtain airbags from deploying improperly and possibly causing
injury, inspect the trim and replace it if it has any
of the following damage:
– Any cracks or deformations in the B-pillar upper trim (B) and the upper hooks (C), and
any stress-whitening in the upper part of the
trim
– Any cracks or deformations in the B-pillar lower trim (D), and any breakages in the part
(E) fitted with the B-pillar upper trim
– Any cracks or stress-whitening in the clips seating surface (F)
 Replace any damaged parts with new ones.
 Make sure the top of the trim overlaps with the headliner correctly (see page 24-187).
 Make sure the pin (G) on the front seat belt shoulder anchor adjuster (H) and the hole (I) on
the back of the slider are engaged when
installing the B-pillar upper trim.
 Make sure the trim hook is installed into the side curtain airbag B-pillar bracket securely.
 Push the clips and the hooks into place securely.
 Before installing the anchor bolt, make sure there are no twists or kinks in the seat belt.
08/08/21 15:01:33 61SNR030_200_0076
ProCarManuals.com
DYNOMITE -2009-


20-79
AB
C
A
B
C Fastener Locations
: Clip, 4(White)
A
B
C D
FG
E
B
D G
A
D
E G
4. Release the hook (A) by pushing in on the detents
(B) on the rear shelf (C), then lift up on the front
edge of the shelf at each detent. 5. Lift the rear shelf (A) upward to detach the
remaining four clips, and release the hooks (B) of
the high mount brake light from the rear shelf.
Release the pin (C) from the holes on the body.
6. Release each anchor rod (D) out through the hole in the rear shelf, and pull both rear seat belts (E) and
rear center seat belt (F) out through the slits (G) in
the rear shelf.
7. Install the shelf in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 When installing the rear shelf, slip the rear seat belt through the slit and the rear center seat belt
into the lid opening in the rear shelf.
 Push the clips and the hooks into place securely.
 Make sure the high mount brake light connector is connected securely.
08/08/21 15:01:36 61SNR030_200_0081
ProCarManuals.com
DYNOMITE -2009-



Î
(#'

 )
S

pecial Tools Required
20-84 Interior Trim
Headliner Removal/Installation
A
B
C A
B
F
astener Locations
:TORXScrew,2
AB
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations, (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Do the battery terminal disconnection procedure (see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items:  A-pillar trim, both sides (see page 20-69)
 Ceiling light (see page 22-197)
 Front seat belt upper anchor, both sides (see step6 on page 24-4)
 B-pillar lower trim, both sides (see page 20-72)
 B-pillar upper trim, both sides (see page 20-72)
 C-pillar trim, both sides (see page 20-75)
 Grab handles, four places (see page 20-82)
3. Release the tabs (A) from the bracket (B) of the sunvisor cap (C) with a trim tool. 4

. Remove the sunvisor cap (A) from the bracket (B).
5. From both sides, remove the sunvisor (A). –1 Remove the sunvisor from the body and theholder (B).
–2 Remove the screws with a TORX T25 bit.
–3 Remove the sunvisor from the body, and if equipped disconnect the vanity mirror light
connector.
08/08/21 15:01:39 61SNR030_200_0086
ProCarManuals.com
DYNOMITE -2009-




Passenger’s seat
Driver’s seat
20-119
Fastener Locations
:Bolt,2
10x1.25mm
Fastener Locations :Bolt,2
10x1.25mm A
B C
D
F
A
A B
C
D E
A
6. Remove the rear seat track bolts.
7. Slide the front seat rearward fully, and remove the
front seat track bolts. 8. Lift up the front seat, then detach the harness clips
(A), and disconnect the side airbag connector (B),
the seat belt switch connector (C), and the seat belt
buckle tensioner connector (D). On the driver’s seat,
disconnect the seat heater subharness connector
(E) or the seat position sensor connector. On the
passenger’s seat, disconnect the seat heater
subharness connector (F) or the ODS unit
subharness connector.
(cont’d)
08/08/21 15:03:54 61SNR030_200_0121
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

Passenger’s Seat
20-12020-120 Seats
Front Seat Removal/Installation
(cont’d)
Front Seat Frame Replacement
Fastener Locations
:Bolt,4
10x1.25mm
34 N·m
(3.5 kgf·m, 25 lbf·ft) A
A
B
C
Fastener Locations
:Clip,4
A
9. With the help of an assistant, carefully remove thefront seat through the front door opening.
10. Install the seat in the reverse order of removal, and note these items:
 Apply medium strength liquid thread lock to the seat mounting bolts before reinstallation.
 Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat (A)
all the way back and tighten and , then slide
it forward and tighten and . The driver’s seat
is shown; the passenger’s seat is similar.
 Tighten the bolts by hand first, then tighten them to specification with a torque wrench.
 Make sure each connector is plugged in properly.
 Check for any DTCs that may have been set during repairs, and clear them.
 Do the battery terminal reconnection procedure (see page 22-68). Calibrate the ODS unit after any of these actions
(see page 24-27):
 Front passenger’s seat replacement (including any seat components)
 Replacement of the front seat weight sensors
 After a vehicle collision
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide locks.
 Apply multipurpose grease to the sliding portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover (see page 20-123)
 Front seat cushion cover (see page 20-127)
 ODS unit (see page 24-209)
 Front seat belt buckle (see page 24-6)
3. Remove the clips, then remove the recline inner covers (A) and module holder (B) from the seat
frame (C).
08/08/21 15:03:55 61SNR030_200_0122
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

Passenger’s Seat
20-12020-120 Seats
Front Seat Removal/Installation
(cont’d)
Front Seat Frame Replacement
Fastener Locations
:Bolt,4
10x1.25mm
34 N·m
(3.5 kgf·m, 25 lbf·ft) A
A
B
C
Fastener Locations
:Clip,4
A
9. With the help of an assistant, carefully remove thefront seat through the front door opening.
10. Install the seat in the reverse order of removal, and note these items:
 Apply medium strength liquid thread lock to the seat mounting bolts before reinstallation.
 Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat (A)
all the way back and tighten and , then slide
it forward and tighten and . The driver’s seat
is shown; the passenger’s seat is similar.
 Tighten the bolts by hand first, then tighten them to specification with a torque wrench.
 Make sure each connector is plugged in properly.
 Check for any DTCs that may have been set during repairs, and clear them.
 Do the battery terminal reconnection procedure (see page 22-68). Calibrate the ODS unit after any of these actions
(see page 24-27):
 Front passenger’s seat replacement (including any seat components)
 Replacement of the front seat weight sensors
 After a vehicle collision
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide locks.
 Apply multipurpose grease to the sliding portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover (see page 20-123)
 Front seat cushion cover (see page 20-127)
 ODS unit (see page 24-209)
 Front seat belt buckle (see page 24-6)
3. Remove the clips, then remove the recline inner covers (A) and module holder (B) from the seat
frame (C).
08/08/21 15:03:55 61SNR030_200_0122
ProCarManuals.com
DYNOMITE -2009-


(#'
 )
Driver’s Seat
20-122 Seats
Front Seat Frame Replacement (cont’d)
A
B
C
D
Fastener Locations
:Clip,3
A
E
Check the operation of the driver’s seat position sensor
after any of these actions (see page 24-29):
 Driver’s seat position sensor replacement
 Cover plate (front side of driver’s seat slide rail) replacement
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide lock.
 Apply multipurpose grease to the sliding portions and pivot portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover/pad (see page 20-123)
 Front seat cushion cover/pad (see page 20-127)
 Driver’s seat position sensor (see page 24-211)
 Front seat belt buckle (see page 24-6) 3. Remove the clips, then remove the recline inner
covers (A), the outer upper rail cover (B), the inner
upper rail cover (C) and the module holder (D) from
the seat frame (E).
4. Install the new seat frame in the reverse order of removal, and note these items:
 Make sure the driver’s seat position sensor connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
 Make sure the seat wiring harnesses are routed properly and not pinched.
08/08/21 15:03:56 61SNR030_200_0124
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

S

pecial Tools Required
20-127
Front Seat Cushion Cover Replacement
Fastener Locations
AB
C
:Screw,2
BFas

tener Locations
:Screw,1
C:Clip,1
AB
B
A
Passenger’s seat
Driver’s seat C
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
 Check the operation of the driver’s seat position sensor after any of these actions (see page 24-29):
– Driver’s seat position sensor replacement
– Cover plate (front side of driver’s seat slide rail) replacement
 Calibrate the ODS unit after any of these actions (see page 24-27):
– Front passenger’s seat replacement (including any seat components)
– Replacement of the front seat weight sensors
– After a vehicle collision
NOTE:  Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to tear or damage the seat covers.
 Put on gloves to protect your hands.
1. Remove the front seat (see page 20-118).
2. Remove the front seat belt buckle (see page 24-6).
3. Pull back the cap (A) to release the hooks (B), and remove the screws, then remove the height
adjuster handle (C). 4.

Remove the recline cover (A).
–1 Remove the recline knob (B) and the screw.
–2 Gently pull out the cover, then detach the clip, and release the hooks (C).
(cont’d)
08/08/21 15:03:59 61SNR030_200_0129
ProCarManuals.com
DYNOMITE -2009-



20-132Seats
Rear Seat Removal/Installation (cont’d)
Fastener Location
:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) FG
H
A B
C
D
E
B A
B
C
D
A
B
Front
4. Remove the left seat-back (A). –1 Fold the left seat-back down.
–2 Pull the rear center seat belt (B) out through theslit (C) in the seat belt guide (D).
–3 Release the Velcro fastener (E), and pull back the seat-back cover (F), then remove the bolt.
–4 Release the hooks (G) of the pivot bracket (H). 5. Extend the rear center seat belt (A) to remove the
left seat-back (B), then release the pivot shaft (C)
from the center pivot bracket (D).
6. If necessary, remove the bushing (A) from the center pivot bracket (B).
08/08/21 15:04:03 61SNR030_200_0134
ProCarManuals.com
DYNOMITE -2009-


Seat Cushion
20-133
Fastener Location:Bolt,1
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A B
Fastener Location
:Bolt,1
7. Remove the seat cushion and seat side bolster.
8. Remove the bolt, then remove the pivot bracket (A).
9. Install the seat-back in the reverse order of removal, and note these items:
 Guide the belt over the front of the seat-back as you install the seat-back.
 Before attaching the rear seat-back, make sure there are no twists or kinks in the rear center seat
belt. NOTE: Take care not to scratch the body or tear the seat
covers.
1. Remove the bolt between the seat-back (A) and the seat cushion (B).
(cont’d)
08/08/21 15:04:03 61SNR030_200_0135
ProCarManuals.com
DYNOMITE -2009-