dashboard ACURA CSX 2006 Service Service Manual


How to Use the HDS (Honda Diagnostic
System)How to Retrieve DTCs
How to Clear DTCs
19-99
A
1. If the system indicators stay on, connect the HDS to
the data link connector (DLC) (A) located under the
driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the VSA modulator-control unit. If it doesn’t,
troubleshoot the DLC circuit (see page 11- 204).
4. Check the diagnostic trouble code (DTC) for all systems, troubleshoot the powertrain DTCs first
and note it. Then refer to the indicated DTC’s
troubleshooting, and do the appropriate
troubleshooting procedure.
NOTE: The HDS communication stops when the vehicle speed is at 50 km/h (31 mph) or more.
 The HDS reads the DTC, current data, and other system data.
 For specific operations, refer to the Help menu that came with the HDS. 1. With the ignition switch in LOCK (0), connect the
HDS to the data link connector (DLC) under the
driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the VSA modulator-control unit. If it doesn’t
troubleshoot the DLC circuit (see page 11-204).
4. Follow the prompts on the HDS to display the DTC(s) on the screen. After determining the DTC,
refer to the DTC troubleshooting. Do the all
systems DTC check, and troubleshoot any
powertrain DTCs first.
5. Turn the ignition switch to LOCK (0).
1. With the ignition switch in LOCK (0), connect the HDS to the data link connector (DLC) under the
driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the VSA modulator-control unit. If it doesn’t
troubleshoot the DLC circuit (see page 11-204).
4. Clear the DTC(s) by following the screen prompts on the HDS.
5. Turn the ignition switch to LOCK (0).
08/08/21 15:04:51 61SNR030_190_0099
ProCarManuals.com
DYNOMITE -2009-


(#'


 ) 
(#'
)
19-16919-169
Yaw Rate-Lateral Acceleration
Sensor Replacement VSA Sensor Neutral Position
Memorization
AB
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
NOTE:
 Do not damage or drop the sensor as it is sensitive.
 Do not use power tools when replacing the sensor.
1. Turn the ignition switch to LOCK (0).
2. Remove the center console (see page 20-92).
3. Remove the yaw rate-lateral acceleration sensor (A) mounting bolts.
4. Pull out the yaw rate-lateral acceleration sensor, then disconnect the sensor connector (B).
5. Install the yaw rate-lateral acceleration sensor in the reverse order of removal.
6. Do the VSA sensor neutral position memorization (see page 19-169). NOTE: Do not press the brake pedal during this
procedure.
1. Park the vehicle on a flat and level surface, with the steering wheel in the straight ahead position.
2. With the ignition switch in LOCK (0), connect the HDS to the data link connector (DLC) (A) under the
driver’s side of the dashboard.
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the vehicle and the VSA modulator-control unit. If it doesn’t
troubleshoot the DLC circuit (see page 11-204).
5. Select VSA ADJUSTMENT with the HDS, and follow the screen prompts.
NOTE: See the HDS Help menu for specific
instructions.
6. Turn the ignition switch to LOCK (0).
08/08/21 15:06:46 61SNR030_190_0169
ProCarManuals.com
DYNOMITE -2009-



(#'

)
´µ
19-170 VSA System Components
VSA OFF Switch Test
A
B
VSA OFF SWITCH 5P CONNECTOR GND VSA OFF SW VSA OFF SWITCH 5P CONNECTOR
ILL ( ) ILL ( )
1. Turn the ignition switch to LOCK (0).
2. Remove the driver’s dashboard lower cover(see page 20-102).
3. Push out the VSA OFF switch (A) from the back of the instrument panel.
4. Disconnect the VSA OFF switch 5P connector (B).
5. Check for continuity between the VSA OFF switch 5P connector terminals No. 1 and No. 2 . There
should be continuity when the button is pressed,
and no continuity when the button is released. 6. Check for continuity between VSA OFF switch 5P
connector terminals No. 4 and No. 5. There should
be continuity at all times.
7. Install the VSA OFF switch in the reverse order of removal.
Terminal side of male terminals Terminal side of male terminals
08/08/21 15:06:46 61SNR030_190_0170
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Body
Doors
Mirrors
Glass
MoonroofInterior Trim
Consoles
Dashboard
.............................................. ..............................................
Special Tools . 20-2
............................................ ..
.... ...
................
...........................................
........................................... ...
..... ....
..................
...........................................
........................................... .......
.............................................
............................................. ............................................
..
.... ...
................
...........................................
........................................... ...
..... ....
..................
...........................................
........................................... .......
.............................................
.............................................
Component Location Index
- Front Door . 20-3
Component Location Index - Rear Door . 20-5
Front Door Panel Removal/Installation . 20-7
Front Door Outer Handle Replacement . 20-9
Front Door Latch Replacement . 20-12
Front Door Glass and Regulator Replacement . 20-14
Front Door Glass Outer Weatherstrip Replacement . 20-15
Front Door Weatherstrip Replacement . 20-16
Rear Door Panel Removal/Installation . 20-17
Rear Door Outer Handle Replacement . 20-19
Rear Door Latch Replacement . 20-21
Rear Door Glass and Regulator Replacement . 20-23
Rear Door Glass Outer Weatherstrip Replacement . 20-26
Rear Door Weatherstrip Replacement . 20-27
Front and Rear Door Glass Adjustment . 20-28
Front and Rear Door Position Adjustment . 20-29
Front and Rear Door Striker Adjustment . 20-31
......................
......................
.......................................
......................
......................
......................
.................
Component Location Index . 20-32
Power Mirror Replacement . 20-33
Mirror Holder Replacement . 20-34
Rearview Mirror Replacement . 20-35
......................
.......................... .............
...................... ......................
.......................... .............
......................
Component Location Index
. 20-36
Windshield Replacement . 20-38
Front Corner Glass Replacement . 20-43
Rear Window Replacement . 20-47
...................... ............
.......................
.................................... ....................
.....................
............................
................................... .......
......................... ..
......................
............
.......................
.................................... ....................
.....................
............................
................................... .......
......................... ..
Component Location Index
. 20-53
Symptom Troubleshooting Index . 20-54
Glass Position Adjustment . 20-55
Glass Replacement . 20-55
Wind Deflector Replacement . 20-56
Drain Channel Replacement . 20-57
Sunshade Replacement . 20-58
Motor Replacement . 20-59
Frame and Drain Tube Replacement . 20-60
Drain Channel Slider and Cable Assembly Replacement . 20-62
Closing Force and Opening Drag Check . 20-64 ......................
..
..
.................................... ..
.....
...........
................
.................................. ......................
..
..
.................................... ..
.....
...........
................
..................................
Component Location Index
. 20-65
Trim Removal/Installation - Door Areas . 20-66
Trim Removal/Installation - Pillar Areas . 20-69
Trim Removal/Installation - Rear Shelf Area . 20-78
Trim Removal/Installation - Trunk Area . 20-80
Trim Removal/Installation - Trunk Lid . 20-82
Grab Handle Removal/Installation . 20-82
Headliner Removal/Installation . 20-84
Carpet Replacement . 20-88
......
..................... ....
...................... ......
..................... ....
......................
Center Console Removal/Installation . 20-92
Center Console
Disassembly/Reassembly . 20-95
Center Console Armrest Replacement . 20-96
Armrest Lock Replacement . 20-96
..............................
.............................. ...
..............................
.............................. .........
.............................. ....................
...............
..............................
..............................
.............................. .....................
..............................
..............................
...
..............................
.............................. .........
.............................. ....................
...............
..............................
..............................
.............................. .....................
Instrument Panel
Removal/Installation . 20-98
Gauge Control Module (Speedo) Trim Removal/Installation . 20-99
Subdisplay Visor Removal/Installation . 20-100
Driver’s Dashboard Lower Cover Removal/Installation . 20-102
Driver’s Dashboard Undercover Removal/Installation . 20-103
Center Pocket Removal/Installation . 20-103
Passenger’s Dashboard Undercover Removal/Installation . 20-104
Glove Box Removal/Installation . 20-104
Dashboard Vent Removal/Installation . 20-105
Glove Box Striker Replacement . 20-107
Dashboard Side Trim Removal/Installation . 20-107
Side Defogger Vent Trim Removal/Installation . 20-108
Dashboard/Steering Hanger Beam Removal/Installation . 20-108
Dashboard/Steering Hanger Beam Disassembly/Reassembly . 20-114
08/08/21 14:58:49 61SNR030_200_0002
ProCarManuals.com
DYNOMITE -2009-

Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior TrimFenderwell
Openers
Frame......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
Component Location Index
. 20-116
Front Seat Active Head Restraint Inspection . 20-117
Front Seat Removal/Installation . 20-118
Front Seat Frame Replacement . 20-120
Front Seat-back Cover Replacement . 20-123
Front Seat Cushion Cover Replacement . 20-127
Rear Seat Removal/Installation . 20-131
Rear Seat-back Latch Replacement . 20-135
Rear Seat-back Release Lever/Cable Removal/Installation . 20-136
Rear Seat Armrest Beverage Holder Replacement . 20-137
Rear Seat Armrest Replacement . 20-138
Rear Seat-back Cover Replacement . 20-139
Rear Seat Side Bolster Cover Replacement . 20-143
Rear Seat Cushion Cover Replacement . 20-143
Rear Seat Armrest Cover Replacement . 20-144
.........
...........................................
........................................... ..........
........................................... .........
...........................................
........................................... ..........
...........................................
Front Bumper Removal/Installation . 20-146
Front Bumper Lower Grille
Replacement . 20-148
Front Bumper Lower Side Plate Replacement . 20-148
Rear Bumper Removal/Installation . 20-149
Rear Bumper Lower Cover Replacement . 20-151
...................................... ................................................
......................................
................................................
Hood Adjustment
. 20-152
Hood Seal Replacement . 20-153
Hood Insulator Replacement . 20-154
................................ ..............
..............
................................
..............
..............
Trunk Lid Adjustment
. 20-155
Trunk Lid Torsion Bar Replacement . 20-156
Trunk Lid Weatherstrip Replacement . 20-157
Trunk Lid Cushion Replacement . 20-157
.........................................
.........................
................
Fuel Fill Door Adjustment
. 20-158
Fuel Cap Adapter Replacement . 20-159
........................................
...............
.......................... ......................
...................... ...
..............
................
..................
..........................
..............
...............
.......................... ......................
...................... ...
..............
................
..................
Front Grille Replacement
. 20-160
Front Fender Trim Replacement . 20-162
Front Grille Cover Replacement . 20-163
Cowl Cover Replacement . 20-163
Roof Molding Replacement . 20-165
Door Molding Replacement . 20-167
Side Sill Protection Tape Replacement . 20-168
Rear License Trim Replacement . 20-168
Trunk Lid Spoiler Replacement . 20-169
Emblem/Sticker Replacement . 20-170 .............
...................... ............
......
.............
.............
......................... .................... .............
...................... ............
......
.............
.............
......................... ....................
Front Inner Fender Replacement . 20-171
Splash Shield Replacement
. 20-172
Front Fender Fairing Replacement . 20-173
Middle Floor Undercover Replacement . 20-174
Rear Floor Undercover Replacement . 20-174
Fuel Pipe Protector Replacement . 20-175
Rear Fender Cover Replacement . 20-175
Rear Strake Replacement . 20-176
Rear Air Outlet Replacement . 20-176
...................... ............
..................
..........................
........................................... .....
...................
......................
............
..................
..........................
........................................... .....
...................
Component Location Index
. 20-177
Hood Opener Cable Replacement . 20-178
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement . 20-179
Hood Latch Replacement . 20-181
Trunk Lid Opener/Fuel Fill Door Opener Replacement . 20-182
Trunk Lid Lock Cylinder Replacement . 20-184
Trunk Lid Latch Replacement . 20-185
...........................................
........................................... ............................
...................................
...........................................
...........................................
............................
...................................
Upper Dashboard Support Gusset
Replacement . 20-186
Rear Floor Upper Cross-member Gusset Replacement . 20-186
Subframe Replacement . 20-187
Frame Repair Chart . 20-188
08/08/21 14:58:49 61SNR030_200_0003
ProCarManuals.com
DYNOMITE -2009-




(#'
 ) Cutting positions
20-38
Glass
Windshield Replacement
A
B A
B A
B
C
A B
A
A
A
C
A
NOTE:
 Put on gloves to protect your hands.
 Wear eye protection while cutting the glass adhesive with a piano wire.
 Use seat covers to avoid damaging the seat.
 When replacing a broken windshield, a commercially available windshield cutter can be efficiently used for
cutting the adhesive. For details, follow the tool
manufacturer’s instructions.
1. Remove these items:  Windshield wiper arms (see page 22-233)
 Cowl covers (see page 20-163)
 Rearview mirror (see page 20-35)
 A-pillar trim, both sides (see page 20-69)
 Roof moldings (see page 20-165)
2. Remove the molding (A) from the upper edge of the windshield (B). If necessary, cut the molding with a
utility knife.
3. If the old windshield will be reinstalled, make alignment marks across the glass and the body
with a grease pencil.
4. Pull down the front portion of the headliner (see page 20-84). Take care not to bend the
headliner excessively, or you may crease or break
it.
5. Apply protective tape along the edge of the dashboard and the body. Make a hole with an awl
through the rubber dam and adhesive from inside
the vehicle at a corner of the windshield. Push a
piece of piano wire through the hole, and wrap
each end around a piece of wood. 6. With a helper on the outside, pull the piano wire (A)
back and forth in a sawing motion. Hold the piano
wire as close to the windshield (B) as possible to
prevent damage to the body and the dashboard.
Carefully cut through the rubber dam and adhesive
(C) around the entire windshield.
7. Carefully remove the windshield.
08/08/21 15:00:07 61SNR030_200_0040
ProCarManuals.com
DYNOMITE -2009-


Rubber dams adhesive tape:
Thickness 0.16 mm (0.006 in.)
Width 3.5 mm (0.14 in.)
Clips adhesive tape: Thickness 0.4 mm (0.016 in.)
Width 10 mm (0.39 in.)
20-39
Inside 11 mm
(0.43 in.)
B
D
12.3 mm
(0.48 in.) B
A
CE
E
E
AC B
D
12.3 mm
(0.48 in.)
12.8 mm
(0.5 in.) F
8. Scrape smooth the old adhesive, using a puttyknife or similar tool, until there is a thickness of
about 2 mm (0.08 in.) on the bonding surface
around the entire windshield opening flange:
 Do not scrape down to the painted surface of the body; damaged paint will interfere with proper
bonding.
 Remove the rubber dam and fasteners from the body.
 Replace the dashboard seal with a new one.
9. Clean the body bonding surface with a shop towel dampened in isopropyl alcohol. After cleaning,
keep oil, grease and water from getting on the
clean surface.
10. If the old windshield will be reinstalled, scrape off the old adhesive, the fasteners, and the rubber dam
from the windshield with a putty knife. Clean the
bonding surfaces on the inside face and the edge of
the windshield with isopropyl alcohol. Make sure
the bonding surface is kept free of water, oil, and
grease. 11. Attach the upper rubber dam (A), the lower rubber
dam (B), and the clips (C) with adhesive tape to the
inside face of the windshield (D) as shown:
 Be sure the rubber dam and the clips line up with the alignment marks (E).
 Be sure the convex portion (F) of the left and the right clips faces the left side.
 Be careful not to touch the windshield where adhesive will be applied.
(cont’d)
08/08/21 15:00:08 61SNR030_200_0041
ProCarManuals.com
DYNOMITE -2009-



20-45
: Apply body primer here.
16 mm
(0.63 in.)
5mm
(0.2 in.)
5mm
(0.2 in.)
16 mm
(0.63 in.) 16 mm
(0.63 in.)
10 mm (0.39 in.)
7mm(0.28in.)
A Inside
10 mm
(0.39 in.)
A
B
7mm
(0.28 in.)
AA
B C
A
B
8.5 mm
(0.33 in.) 2mm
(0.08 in.)2mm
(0.08 in.)
A B A
B
Inside
Inside
2mm
(0.08 in.)
9mm
(0.35 in.)
9. Carefully apply a light coat of body primer with asponge applicator to any exposed paint or metal
around the flange where new adhesive will be
applied. Let the primer dry for at least 10 minutes:
 Do not apply body primer to any remaining original adhesive on the flange.
 Be careful not to mix up the body and glass primer sponge applicators.
 Never touch the primed surfaces with your hands.
 Mask off the dashboard before painting the flange.
10. Cut a ‘‘V’’ in the end of the nozzle (A) on the adhesive cartridge as shown. 11. Put the cartridge in a caulking gun, and run a
continuous bead of adhesive (A) around the front
corner glass (B) as shown:
 With the printed dots (C) on the front corner glass as a guide, apply the adhesive to both side
portions of the front corner glass.
 Apply the adhesive within 30 minutes after applying the glass primer. Make a slightly thicker
bead at each corner.
(cont’d)
08/08/21 15:00:11 61SNR030_200_0047
ProCarManuals.com
DYNOMITE -2009-



Î
(#'
 )
20-60 Moonroof
Frame and Drain Tube Replacement
A
A B
C
A
A C
C
C
A
B Fastener Locations
:Bolt,9
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
B
B
B
B B
C
A
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
1. Remove these items:  Headliner (see page 20-84)
 Moonroof glass (see page 20-55)
2. Put on gloves to protect your hands. Disconnect the motor connector (A).
3. Disconnect the drain tubes (A).
4. Remove the roof wire harness (B) by detaching the harnessclips(C). 5. With an assistant holding the frame (A), remove the
bolts, starting at the rear, and release the rear
hooks (B) by moving the frame forward.
6. With the help of an assistant, carefully remove the frame through the front door opening. Take care
not to scratch the interior trim or the body, or tear
the seat covers.
7. To remove a front drain tube (A) from the body, remove the kick panel, left or right (see page 20-66),
and the driver’s dashboard undercover (see page
20-103) or the passenger’s dashboard undercover
(see page 20-104). Detach the clips (B) and remove
the drain valve (C) from the body hole, then remove
the front drain tube.
08/08/21 15:01:21 61SNR030_200_0062
ProCarManuals.com
DYNOMITE -2009-






20-70Interior Trim
Trim Removal/Installation - Pillar Areas (cont’d)
A
B C
A
B
C
Fastener Locations : Clip, 2(Black)
A
B A
B
C
D
E
3. Pull the front of the A-pillar trim (A) back by hand toremove the upper clip (B) from the body (C).
4. Pull the A-pillar trim (A) by hand to detach the clips. Pull the trim up from the dashboard (B), then
remove it. 5. If the side curtain airbag has deployed, replace the
A-pillar trim and all clips on the trim with new ones
(see page 24-185).
6. If the side curtain airbag has not deployed, remove the upper clip (A) from the removed A-p illar trim (B)
and discard it. Then check the trim:
 To prevent the side curtain airbags from deploying improperly and possibly causing
injury, inspect the A-pillar trim and replace it if it
has any of the following damage:
– Any cracks, deformations, or stress-whitening in the A-pillar trim
– Any cracks or stress-whitening in the clip seating surfaces (C, D)
 If the clips (E) are damaged or stress-whitened, replace them with new ones.
 Replace the upper clip with a new one.
08/08/21 15:01:31 61SNR030_200_0072
ProCarManuals.com
DYNOMITE -2009-