display ACURA CSX 2006 Service Workshop Manual

Audio GlossaryItem Definition
23-9
GA-Net The GA-Net allows the audio unit to communicate with all the audio and
navigation components in a vehicle. If there is an open in the GA-Net or
components, components or the entire audio and navigation system may
appear inoperative.
GB (Gigabyte) A unit of memory or disk storage equal to billion bytes (1000 million bytes).
HDD Abbreviation for hard disc drive. They are sensitive to heat and it is not
recommended that they be used in the PC card slot for playing audio files.
Hertz (Hz) The unit of frequency equal to one cycle per second (cps). One kilohertz (kHz)
equals 1,000 cps; one megahertz (MHz) equals 1 million cps.
Integrated amplifier A component that combines a pre amp and a power amp into a single unit. A
receiver combines an integrated amp and a tuner into a single unit.
Jewel case The hard plastic case that contains a compact disc or DVD. Always use a jewel
case to prevent scratches on the underside of a CD or DVD.
LCD (Liquid Crystal Display) A type of digital display that changes reflectance or transmittance when an electrical field is applied to it.
Memory Circuitry or devices that hold information in electrical or magnetic form, such
as the AM/FM radio presets.
MB (Megabyte) One million bytes. Written as 1 MB. Megabytes are used as a measure of digital
storage space. For example, a CD can hold 650 MB.
Mic An abbreviation for microphone. For vehicles with navigation, the microphone
accepts navigation voice commands to control audio and navigation functions.
MP3 music files MP3 is an audio coding format. MP3 is a popular audio compression format on
the Internet and computers. CDs and PC Cards with these files can be played on
some vehicle’s audio system.
Mute When the navigation gives guidance, the front speakers are muted (no music).
When you use the voice control system, all of the speakers are muted.
Noise Unwanted random sounds like buzzing, hiss, pops, static, whine, etc.
PC card The slot used for playing MP3 and WMA music files. The PC Card is usually a
combination of a small flash card in a PCMCIA adaptor that slides into the slot.
The ATA, SD, and compact flash types of cards have been tested up to 1 GB.
PCMCIA A computer standard for the slot that the PC card slides into. Another term for
the PC card slot.
Processor The part of an audio device that performs tasks/calculations. In the audio unit
the processor handles muting to allow the navi to speak its voice commands,
and the decoding/playback of the sound files etc.
Radio A head unit that combines a tuner, a preamplifier, and often a power-amplifier.
Route guidance (RG) Spoken voice used for turn-by-turn navigation from the audio speakers.
SCF (Cold Start Fix) screens These screens are displayed if the system requires a GPS initialization. The vehicle should be moved outside into an open area away from buildings/power
lines.
Stereo A recording of at least two channels where you can hear sound or music from
the left or right side.
SD (Secure Digital) card This compact type of memory card allows for fast data transfer and has built-in security functions. SD cards have a small write-protection switch on the side.
Shield A metallic foil or braided wire layer surr ounding conductors which are
designed to prevent electrostatic or electromagnetic interference (noise) from
external sources such as buzzing, or popping sounds heard on the speakers.
Speaker (Loudspeaker) A device that converts electrical energy into acoustical energy (sound).
Speed-sensitive volume
compensation (SVC) The SVC increases the audio volume to compensate for increased interior noise
when the vehicle drivers at freeway speeds.
Subwoofer A loudspeaker made to reproduce the lowest audio frequencies, about 25 Hz to
125 Hz.
(cont’d)
08/08/21 14:03:45 61SNR030_230_0012
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#'#
)
Without Navigation
Serial Number Display Mode
Eight digits of the serial number (example 12345678)
23-23
Self-diagnostic Function
A
The audio system has a self-diagnostic function.
To obtain the audio unit serial number on a vehicle, do the following:
NOTE: This procedure can only be performed when the battery power is disconnected from the audio unit and the audio unit displays CODE.
 To obtain the navigation unit serial number, refer to Navi ECU in the navigation system diagnostic mode (see page 23-135).
1. Turn the ignition switch to ON (II).
2. Make sure the audio system is turned off.
3. Push and hold the preset No. 1 and No. 6 buttons.
4. While holding the buttons, push the VOL PUSH PWR knob (A) to ON.
5. Release the buttons and the self-diagnostic begins.
6. The display shows a 8 digit serial number.
7. Use all 8 numbers as the serial number when using the Interactive Network (iN) to retrieve the 5 digit anti-theft code.
8. To end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
(cont’d)
08/08/21 14:03:50 61SNR030_230_0026
ProCarManuals.com
DYNOMITE -2009-

Î
How to check for audio system condition
No. 3 button
No. 4 button
No. 5 button
FM button (Push and hold 5 sec.)
CD button (Push and hold 5 sec.)
23-24Audio System
Self-diagnostic Function (cont’d)
A
NOTE:
 The audio unit must be in the code enter screen before performing the self-diagnostic function.
 The self-diagnostic function does not find every problem with the audio system. Check any official H onda service
website for more information about the audio system.
1. Turn the ignition switch to ON (II).
2. Make sure the audio system is turned off.
3. Push and hold the preset No. 1 and No. 6 buttons.
4. While holding the buttons, push the VOL PUSH PWR knob (A) to ON.
5. Release the buttons and the self-diagnostic begins.
6. When you are in the self-diagnostic mode, pressing a preset button starts the diagnostic mode that is assigned to that preset switch.
Entire LCD lighting/light-out mode: Turns on/off the entire LCD to show the presence or absence of an LCD failure.
The entire display must appear. If there are dead segments, replace the audio unit.
Duty indication mode (for the Illumination dim): Indicates the duty for the Illumination dim when the dash lights
are on.
Vehicle speed pulse indication mode: Indicates the vehicle speed pulse.
Reception level check mode: Indicates the reception level (dB). When entering the reception level check mode, the
AM/FM button is used to change the main/sub antenna. See reception level indication for more information.
DRAM residual quantity indication mode: Indicates the DRAM residual quantity.
08/08/21 14:03:50 61SNR030_230_0027
ProCarManuals.com
DYNOMITE -2009-

ÎDisplay Specifications
Speaker check mode
23-25
Entry LCD Lighting
No. 3 button Entry LCD Lights-outs
No. 3 button
Duty (for the illumination) indication
No. 4 button
Vehicle speed pulse indication
No. 5 button
Reception level indication
FM button
DRAM residual quantity indication
CD button
7. To end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
8. Turn off the audio unit.
9. Push and hold the No. 1 and No. 3 buttons. While holding the buttons, push the VOL push PWR knob to ON. Release the buttons and the speaker check mode begins. A low-frequency hum should sound for about one
minute. Change the test speaker by pushing the SKIP button. If you find a speaker(s) with no sound, check the
speaker and harness connections. If the connections are good, replace the speaker, and retest.
10. To end the self-diagnostic function, turn the audio unit off, or turn the ignition switch to LOCK (0).
(cont’d)
08/08/21 14:03:51 61SNR030_230_0028
ProCarManuals.com
DYNOMITE -2009-

Reception level indication mode
Preperation:
23-26Audio System
Self-diagnostic Function (cont’d)
This diagnostic screen checks the audio unit’s reception l
evel. This level then can be used in the diagnosis of audio
unit reception quality. The reception level is displayed in decibels (dB)
 Pank the vehicle outdoors in an appropriate location for good radio reception.
 Tune to a powerful local FM radio station then write down the radio station number. 1. Enter the reception level indication mode in the self-dia gnostic function. The AM/FM antenna amplifier is on
(A. SEL or TP is not displayed in the audio-HVAC display).
2. Tune to the FM radio station you wrote down preperation using the T UNING knob, and note the decibel level of
that station when you release the button.
3. Press and release the A. SEL button to turn the AM/FM antenna amplifier off (A. SEL or TP is now displayed in the audio-HVAC display).
4. Tune to the FM radio station you wrote down in preperation using the T UNING knob, and note the decibel level of
that station when you release the button.
5. Press and release the A. SEL button to turn the AM/FM antenna amplifier back on (A. SEL or TP is not displayed in the audio-HVAC display).
6. Turn the ignition switch to LOCK (0) or audio unit off to exit the test mode.
7. Compare your results to a known-good (make sure it is the same year and trim level) in the same location and
direction, and under the same environmental conditions.
08/08/21 14:03:51 61SNR030_230_0029
ProCarManuals.com
DYNOMITE -2009-

(#' 
)

CD Error Codes (’06-07 models and ’08 model with navigation)Error Code Displayed Possible Cause Solution
CD Error Codes (’08 model without navigation) Error Code Displayed Possible Cause Solution
CD Error Codes (’06-08 models) Error Code Displayed Possible Cause Solution
23-27
Error Codes
The audio system displays error codes when a problem is detected with the disc changer, the disc, the XM radio, or
the anti-theft code.
This is not a complete list of audio error codes. Refer to symptom troubleshooting, or go to any official Honda service
website for more service information.
DISC ERROR The system cannot read the disc because an audio or video DVD
is inserted into the unit. The CD
may be inserted upside down.Verify that the unit functions with a standard
mass production CD.
MECH ERROR There is a problem with the mechanism A CD label may be
jammed in the mechanism.Replace the navigation unit.




BAD DISC-PLEASE CHECK
OWNERS MANUAL PUSH
EJECT
CDlabeljammedinthe
mechanism.
CD eject mechanism or motor
is inoperative.
CD spindle motor won’t spin
up the CD.
The wrong type disc is
inserted.Press the EJECT button and hold it for 5
seconds. If the disc does not eject, try again.
If the disc still won’t eject, replace the unit.




HEAT ERROR CD player is too hot. This can
happen if the vehicle is parked
in the sunlight all day.The unit should function normally when it
cools off.
FORMAT Audio unit cannot read the files on the CD or CD-R.Current track is skipped. The next supported
track or file plays automatically.
Verify that CD, CD-R or CD-RW file names
endinCD-AorWMA.
Verify that CD, CD-R or CD-RW with
compressed music formats end in MP3 or
WMA.
Other file formats like I-tunes or Ogg are
not recognized.
WMA files may have (DRM) copy
protection and cannot be read.
(cont’d)
08/08/21 14:03:51 61SNR030_230_0030
ProCarManuals.com
DYNOMITE -2009-

µµµ
XM Error Codes
Error Code Displayed Possible Cause Solution
Audio Unit Error Codes Error Code Displayed Possible Cause Solution
23-28Audio System
Error Codes (cont’d)
LOADING
XM radio is acquiring audio or
program information. Wait until the radio receives the information.
(XM) OFF AIR XM channel not in service. Try another XM channel.
(XM) NO SIGNAL Loss of signal.Both terrestrial and satellite antennas have
lost signal. Park the vehicle outside with a
clear view of the southern horizon.
(XM) UPDATING XM radio is receiving
information update from the
network. This message disappears once the update
finishes.
(XM) CHECK ANTENNA XM antenna error. Repair open or short in the satellite antenna.
Substitute the XM antenna with a known-
good one, and recheck. If the error is gone,
replace the original XM antenna. If the error
is still present, replace the antenna lead.
(XM) ANTENNA ERROR
No signal from XM.Check a known-good vehicle with XM radio.
If the known-good vehicle has the same
symptoms, contact XM Satellite Radio at
800-852-9696.
CODE ERROR 1 Anti-theft code mismatch
(1 try). Enter the correct anti-theft code.
CODE ERROR E Anti-theft code mismatch
(10 try). Remove the No. 23 (10 A) fuse in the under-
hood fuse/relay box, then reinsert it. You will
have 10 more tries to enter the correct anti-
theft code.
NOTE: Do XM error codes checks with the vehicle parked outside with a clear view of the southern horizon.
st
th
08/08/21 14:04:37 61SNR030_230_0031
ProCarManuals.com
DYNOMITE -2009-

Î
(#'#
)
´
µ
µ
µ
µ
µ
µ µ
µ
Audio unit power switch will not turn on (No
information display and no sound) (with
navigation)
YES
NO
YES
NO
YES
NO YES
NO
23-35
NAVIGATION UNIT CONNECTOR A (17P)
BBACKUP(WHT)
ACC RADIO (PUR)NOTE:
 Check the vehicle battery condition first.
 Check the connectors for poor connections or loose terminals.
1. Turn the ignition switch to ON (II).
2. Push the power switch ON to see if the navigation unit turns ON.
Intermittent failure, the system is OK at this
time.
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Check the No. 23 (10 A) fuse in the under-hood fuse/relay box and No. 35 (7.5 A) fuse in the under-
dash fuse/relay box.
Go to step 5.
Replace the fuse(s), and recheck.
5. Remove the navigation unit (see page 23-155). Check that the navigation unit is properly
connected.
NOTE: Eject all the discs before removing the navigation unit to prevent damaging the CD player’s load
mechanism.
 Remove the PC card before removing the navigation unit.
Go to step 6.
Reconnect the connector, and recheck the
function.
6. Disconnect navigation unit connector A (17P)
7. Turn the ignition switch to ON (II). 8. Measure the voltage between body ground and
navigation unit connector A (17P) terminals No. 14
and No. 17 individually.
Go to step 9.
Repair open in the wire(s) between the No. 23
(10 A) fuse in the under-hood fuse/relay box and
the No. 35 (7.5 A) in the under-dash fuse/relay box
and the navigation unit.
9. Turn the ignition switch to LOCK (0).
10. Reconnect navigation unit connector A (17P).
(cont’d)
Wire side of female terminals
Does t he nav i gat i on uni t d i spl ay oper at e pr oper l y ,and d oes t he aud i o sound nor mal ?
Ar e t he f uses OK ?
I s i t connect ed pr oper l y ? I s t her e bat t er y v ol t age on bot h t er mi nal s?
08/08/21 14:04:39 61SNR030_230_0038
ProCarManuals.com
DYNOMITE -2009-

Î

(#'#
)
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
Audio unit power switch will not turn on (No
information display and no sound) (without
navigation)
23-3623-36Audio System
Symptom Troubleshooting (cont’d)
RADIO GND (BLK)
NAVIGATION UNIT CONNECTOR A (17P)
11. Turn the ignition switch to ON (II).
12. Measure the voltage between navigation unit
connector A (17P) terminal No. 9 and body ground.
Replace the navigation unit (see page 23-155).
Repair open in the wire between navigation
unit connector A (17P) terminal No. 19 and body
ground (G 505). NOTE:
 Check the vehicle battery condition first.
 Check the connectors for poor connections or loose terminals.
1. Turn the ignition switch to ON (II).
2. Push the power switch ON to see if audio unit turns ON.
Intermittent failure, the system is OK at this
time.
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Check the No. 23 (10 A) fuse in the under-hood fuse/relay box and the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box.
Go to step 5.
Replace the fuse(s), and recheck.
5. Remove the audio unit (see page 23-80). Check that the audio unit is properly connected.
NOTE: Eject all the discs before removing the audio
unit to prevent damaging the CD player’s load
mechanism.
Go to step 6.
Reconnect the connector, and recheck the
function.
Wire side of female terminals
I s t her e l ess t han 0.1 V on bot h t er mi nal s? Does t he aud i o uni t oper at e pr oper l y , and d oes t he
aud i o sound nor mal ?
Ar e t he f uses OK ?I s i t connect ed pr oper l y ?
08/08/21 14:04:40 61SNR030_230_0039
ProCarManuals.com
DYNOMITE -2009-

Î

(#'#
)
(#'#
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
Audio unit power switch will not turn off
(without navigation) No sound is heard from the speaker(s)
(display is normal) (with navigation)
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
23-3923-39
AUDIO UNIT CONNECTOR A (17P)
ACC RADIO (PUR)
NOTE: Check for aftermarket accessories plugged into the vehicle’s accessory power sockets.
 Check the connectors for poor connections or loose terminals.
1. Turn the ignition switch to ON (II).
2. Push the power switch OFF or turn the ignition switch to LOCK(0) to see if the audio unit turns OFF.
Operation is normal.
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Remove the audio unit (see page 23-80).
5. Disconnect audio unit connector A (17P). NOTE: Eject all the discs before removing the audio
unit to prevent damaging the CD player’s load
mechanism.
6. Measure the voltage between audio unit connector A (17P) terminal No. 14 and body ground.
Check for short to power on PUR wire.
Replace the audio unit (see page 23-80). NOTE:
 Check the vehicle battery condition first.
 Check the connectors for poor connections or loose terminals.
 Set the fader and balance positions to the center.
 Before performing symptom troubleshooting, do the power switch will not turn ON troubleshooting
(see page 23-35).
1. Turn the ignition switch to ON (II).
2. Check for sound in each mode (AM, FM, XM, and CD).
Intermittent failure. The system is OK at this
time. Check for loose connections at the navigation
unit and speaker(s).
Go to step 3.
3. Check that the volume button is not set to the min level.
Raise the volume level, and recheck the
function.
Go to step 4.
4. On the steering wheel, check the navigation talk command.
Cancel the navigation talk command by
pressing the navigation BACK button, then recheck
the function.
Go to step 5.
(cont’d)
Wire side of female terminals
Is the aud io unit OF F ?
Is there voltage? I s t he sound OK i n each mod e?
Is it at the MIN level?I s t he nav i gat i on t al k command f unct i on set ?
08/08/21 14:04:40 61SNR030_230_0042
ProCarManuals.com
DYNOMITE -2009-