turn signal ACURA CSX 2006 Service Workshop Manual


(#' 
'

)
µ
µµ
µ
DTC 27-11:
DTC 27-26:
YES
NO YESNO
19-130VSA System Components
DTC Troubleshooting (cont’d)
STEERING ANGLE SENSOR 5P CONNECTOR
STR-D (BLU)
Steering Angle Sensor DIAG
Signal Error (Initial)
Steering Angle Sensor DIAG
Signal Error (Main)
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it to
ON (II) again.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for loose terminals between the
steering angle sensor 5P connector and the VSA
modulator-control unit 37P connector. Refer to
intermittent failures troubleshooting (see page
19-98).
5. Turn the ignition switch to LOCK (0).
6. Disconnect the steering angle sensor 5P connector.
7. Disconnect the VSA modulator-control unit 37P connector (see step 2 on page 19- 171).8. Check for continuity between steering angle sensor
5P connector terminal No. 3 and body ground.
Repair short to body ground in the wire
between the steering angle sensor and the VSA
modulator-control unit.
Go to step 9.
Wire side of female terminalsI s DT C 27 -11 or 27 -26 i nd i cat ed ? Is there continuity?
08/08/21 15:05:54 61SNR030_190_0130
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
19-168VSA System Components
Steering Angle Sensor Replacement
A
B
C
NOTE: Do not damage or drop the combination switch as the steering angle sensor is sensitive to shock and vibration.
1. With the wheels in the straight-ahead position and the steering wheel centered, remove the steering wheel (see page 17-6).
2. Remove the steering column covers (see page 17-9) and the cable reel (see page 24-200).
3. Remove the combination switch assembly (see step 11 on page 17-11).
4. Remove the combination light switch (A) and the wiper/washer switch (B) from the combination switch body assembly (C).
5. Install the combination switch body assembly in the r everse order of removal.
NOTE:  Do not remove the steering angle sensor from the combination switch body.
 When installing the cable reel, set the turn signal canceling sleeve position so that the arrow points straight up (see page 24-201).
 When installing the combination switch, tighten the m ounting screws to the specified torque and sequence
shown (see page 17-12).
08/08/21 15:06:45 61SNR030_190_0168
ProCarManuals.com
DYNOMITE -2009-



(#'



)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
21-6421-64Climate Control
A/C Compressor Clutch Circuit
Troubleshooting (cont’d)
A/C Signal Circuit Troubleshooting
A/C COMPRESSOR CLUTCH RELAY 4P SOCKET
RED/WHT
A/C COMPRESSOR CLUTCH 3P CONNECTOR PUR
REDBRN
CLIMATE CONTROL UNIT 32P CONNECTOR
19. Disconnect the jumper wire.
20. Disconnect the A/C compressor clutch 3P connector.
21. Check for continuity between the A/C compressor
clutch relay 4P socket terminal No. 2 and the A/C
compressor clutch 3P connector terminal No. 2.
Check the A/C compressor clutch clearance,
and the compressor clutch field coil (see page
21-85). Repair as needed.
Repair open in the wire between the A/C
compressor clutch relay and the A/C compressor
clutch. NOTE:
 Do not use this troubleshooting procedure if any of the following items are operative: A/C condenser fan,
radiator fan, A/C compressor. Refer to the symptom
troubleshooting index.
 Before doing symptom troubleshooting, check for powertrain DTCs (see page 11-3).
1. Connect the HDS to the DLC.
2. Start the engine.
3. Turn on the A/C.
4. Check the A/C SWITCH in the PGM-FI Data List with the HDS.
The A/C signal is OK at this time.
Go to step 5.
5. Turn the ignition switch to LOCK (0), and disconnect the climate control unit 32P connector.
6. Measure the evaporator temperature sensor resistance between the climate control unit 32P
connector terminals No. 8 and No. 19.
Go to step 7.
Test the evaporator temperature sensor
(see page 21-70).
Wire side of female terminals
Wire side of female terminals
Is there continuity?Is the A/ C SW IT CH on?
I s r esi st ance l ess t han 24 k ?
08/08/21 14:43:33 61SNR030_210_0065
ProCarManuals.com
DYNOMITE -2009-



(#'



)
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
21-6421-64Climate Control
A/C Compressor Clutch Circuit
Troubleshooting (cont’d)
A/C Signal Circuit Troubleshooting
A/C COMPRESSOR CLUTCH RELAY 4P SOCKET
RED/WHT
A/C COMPRESSOR CLUTCH 3P CONNECTOR PUR
REDBRN
CLIMATE CONTROL UNIT 32P CONNECTOR
19. Disconnect the jumper wire.
20. Disconnect the A/C compressor clutch 3P connector.
21. Check for continuity between the A/C compressor
clutch relay 4P socket terminal No. 2 and the A/C
compressor clutch 3P connector terminal No. 2.
Check the A/C compressor clutch clearance,
and the compressor clutch field coil (see page
21-85). Repair as needed.
Repair open in the wire between the A/C
compressor clutch relay and the A/C compressor
clutch. NOTE:
 Do not use this troubleshooting procedure if any of the following items are operative: A/C condenser fan,
radiator fan, A/C compressor. Refer to the symptom
troubleshooting index.
 Before doing symptom troubleshooting, check for powertrain DTCs (see page 11-3).
1. Connect the HDS to the DLC.
2. Start the engine.
3. Turn on the A/C.
4. Check the A/C SWITCH in the PGM-FI Data List with the HDS.
The A/C signal is OK at this time.
Go to step 5.
5. Turn the ignition switch to LOCK (0), and disconnect the climate control unit 32P connector.
6. Measure the evaporator temperature sensor resistance between the climate control unit 32P
connector terminals No. 8 and No. 19.
Go to step 7.
Test the evaporator temperature sensor
(see page 21-70).
Wire side of female terminals
Wire side of female terminals
Is there continuity?Is the A/ C SW IT CH on?
I s r esi st ance l ess t han 24 k ?
08/08/21 14:43:33 61SNR030_210_0065
ProCarManuals.com
DYNOMITE -2009-


µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
21-66Climate Control
A/C Signal Circuit Troubleshooting (cont’d)
A/C COMPRESSOR CLUTCH 3P CONNECTOR
GRN/RED RED/BLK
A/C COMPRESSOR CLUTCH 3P CONNECTOR BRN
CLIMATE CONTROL UNIT 32P CONNECTOR
18. Turn the ignition switch to LOCK (0).
19. Disconnect the A/C compressor clutch 3P connector.
20. Turn the ignition switch to ON (II).
21. Measure the voltage between the A/C compressor
clutch 3P connector terminal No. 1 and body
ground.
Go to step 22.
Repair open in the wire between the A/C
compressor and the MICU. If the wire is OK,
substitute a known-good MICU and recheck. If the
symptom goes away, replace the original MICU
(see page 22-66).
22. Test the A/C compressor thermal protector (see page 21-85).
Go to step 23.
Replace the A/C compressor thermal
protector (see page 21-87). 23. Check for continuity between the climate control
unit 32P connector terminal No. 6 and the A/C
compressor clutch 3P connector terminal No. 3.
Check for loose wires or poor connections at
the climate control unit 32P connector and at the
A/C compressor clutch 3P connector.
Repair open in the wire between the climate
control unit and A/C compressor.
Wire side of female terminals Wire side of female terminalsWire side of female terminals
Is there battery voltage?
I s t he A/ C compr essor t her mal pr ot ect or OK ? Is there continuity?
08/08/21 14:43:34 61SNR030_210_0067
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Body Electrical
Body Electrical..................................
..................................
Relay and Control Unit
Locations . 22-7
................
Connectors and Harnesses . 22-13
........................
........................
Fuse/Relay Boxes . 22-58
......................
......................
Power Distribution . 22-60
....................
....................
Ground Distribution . 22-64
Under-hood Fuse/Relay Box
Under-dash Fuse/Relay Box
Battery
Relays
Ignition Switch
Multiplex Integrated Control System Keyless/Power Door Locks/Security
System
Horns
Exterior Lights
Turn Signal/Hazard Warning Lights
Interior Lights.............................................. .....
..............................................
.....
Special Tools . 22-2
General Troubleshooting Information . 22-3
.......................... ..........................
Removal and Installation . 22-65
..........................
..........................
Removal and Installation . 22-66
.......................................................................................... .............
................................................
.......................................... .............
Battery Test
. 22-67
Battery Terminal Disconnection and Reconnection . 22-68
Battery Removal and Installation . 22-69
.......................................
.......................................
Power Relay Test . 22-70
............................................................. ..............................................
.............................................................
..............................................
Test
. 22-72
Replacement . 22-72
...................... .....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
......................................... ......................
.....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
.........................................
Component Location Index
. 22-73
General Troubleshooting Information . 22-74
DTC Troubleshooting Index . 22-77
System Description . 22-80
Troubleshooting-B-CAN System Diagnosis Test Mode A . 22-93
Troubleshooting-B-CAN System Diagnosis Test Mode B . 22-94
Troubleshooting-B-CAN System Diagnosis Test Mode C . 22-95
Troubleshooting-B-CAN System Diagnosis Test Mode D . 22-96
Troubleshooting-B-CAN System Diagnosis Test Mode 1 and
Test Mode 2 (Without the HDS) . 22-97
Sleep and Wake-up Mode Test . 22-99
Circuit Diagram . 22-100
DTC Troubleshooting . 22-102
MICU Input Test . 22-109 ......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
Component Location Index
. 22-112
System Description . 22-114
Circuit Diagram . 22-116
DTC Troubleshooting . 22-120
Symptom Troubleshooting . 22-126
Tripped Sensor History . 22-130
MICU Input Test . 22-131
Door Lock Actuator Test . 22-137
Door Lock Knob Switch Test . 22-138
Door Lock Switch Test . 22-139
Door Key Cylinder Switch Test . 22-140
Trunk Lid Release Actuator Test . 22-141
Hood Switch Test . 22-141
Transmitter Test/Replacement . 22-142
......................
.......................................... ............................
....................................... ......................
.......................................... ............................
.......................................
Component Location Index
. 22-145
Circuit Diagram . 22-146
Horn Test/Replacement . 22-146
Horn Switch Test . 22-147
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
Component Location Index
. 22-148
Circuit Diagram . 22-150
DTC Troubleshooting . 22-157
MICU Input Test . 22-163
Combination Light Switch Test/ Replacement . 22-166
HID Bulb Replacement . 22-168
HID Unit Replacement . 22-169
HID Lamp System Troubleshooting . 22-170
Headlight Adjustment . 22-173
Headlight Replacement . 22-174
Fog Light Replacement . 22-175
Fog Light Adjustment . 22-176
Bulb Replacement . 22-177
Taillight Replacement . 22-179
Inner Taillight Replacement . 22-179
License Plate Light Replacement . 22-180
High Mount Brake Light Replacement . 22-180
Brake Pedal Position Switch Test . 22-181
......................
.......................................... ................................
.........................................
.................................. .......
......................
.......................................... ................................
.........................................
.................................. .......
Component Location Index
. 22-182
Circuit Diagram . 22-184
DTC Troubleshooting . 22-186
MICU Input Test . 22-188
Hazard Warning Switch Test/Replacement . 22-192
Side Turn Signal Light Replacement . 22-192
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
Component Location Index
. 22-193
Circuit Diagram . 22-194
Front Individual Map Light Test/ Replacement . 22-196
Ceiling Light Test/Replacement . 22-197
Trunk Light Replacement . 22-197
Ambient Light Test/Replacement . 22-198
Courtesy Light Replacement . 22-198
Glove Box Light Test/Replacement . 22-199
Vanity Mirror Light Test/Replacement . 22-199
Interior Light Switch Test/Replacement . 22-200
Trunk Lid Latch Switch Test . 22-200
Footwell Light Test/Replacement . 22-201
08/08/21 14:22:03 61SNR030_220_0002
ProCarManuals.com
DYNOMITE -2009-

•••
•••
•••
•••
(#')
 Under-hood Fuse/Relay Box
Fuse
Number Amps Component(s) or Circuit(s) Protected
22-60Power Distribution
Fuse to Components Index
1 100 A
(BAT)Battery, Power distribution
70 A
(EPS) EPS control unit
250A (IG)Ignition switch
80 A
60 A
(OPTION) No. 5, No. 6, No. 7, No. 27, No. 28, No. 29, and No. 31 fuses (in the under-dash fuse/relay box)
330A (ABS MTR) ABS modulator-control unit , VSA modulator-control unit
30 A
40 A
(ABS FSR) ABS modulator-control unit , VSA modulator-control unit
450A (H/L)No. 18, No. 19, No. 20, and No. 21 fuses (in the under-dash fuse/relay box)
40 A
(P/W) No. 24, No. 25, No. 26, No. 30, No. 32, and No. 33 fuses (in the under-dash fuse/relay box), Power window relay
(in the under-dash fuse/relay box)
5 Not used
6 20 A A/C condenser fan motor (via A/C condenser fan relay)
7 20 A Radiator fan motor (via radiator fan relay)
8 30 A Noise condenser (via rear window defogger relay), Rear window defogger (via rear window defogger relay)
9 40 A Blower motor (via blower motor relay)
10 10 A MICU (turn signal/hazard warning lights circuit)
11 15 A A/F sensor (Sensor 1) (via PGM-FI subrelay), EVAP canister vent shut valve (via PGM-FI subrelay), PGM-FI subrelay, No. 15 fuse (in the under-hood fuse/relay box) (via PGM-FI subrelay)
12 15 A Brake lights, ECM/PCM, Horn, MICU
13 Not used
14 Not used
15 7.5 A A/C condenser fan relay
16 Not used
17 15 A Stereo amplifier
18 15 A Ignition coil relay, Ignition coils (via Ignition coil relay)
19 15 A CKP sensor (via PGM-FI main relay 1), CMP sensor B (via PGM-FI main relay 1), ECM/PCM, ETCS control relay, Injectors (via PGM-FI main relay 1), PGM-FI main relay 1 (FI MAIN), PGM-FI main relay 2 (FUEL PUMP)
20 7.5 A A/C compressor clutch (via A/C compressor clutch relay)
21 15 A ECM/PCM (via ETCS control relay)
22 7.5 A Ceiling light, Courtesy lights, Front individual map lights, Ignition key light, Trunk light, Vanity mirror lights
23 10 A Audio unit , Data link connector (DLC), Gauge control module (speedo), Gauge control module (tach), HandsFreeLink control unit , Immobilizer-keyless control unit, MICU, Moonroof switch, Navigation unit
1: ’06-07 models
2: ’08-09 models
3: ’06-07 Touring and Premium models
4: ’07 TYPE S and ’08-09 models
5: ’08-09 models
6: TYPE S model
7: Without navigation system
8: With navigation system
9: ’09 model with navigation system
1
2
34
3
4 34
6 5
7 9 8
08/08/21 14:24:02 61SNR030_220_0062
ProCarManuals.com
DYNOMITE -2009-

µ
(#'
)
GroundComponent or Circuit Grounded
22-64Ground Distribution
Ground to Components Index
G1 Battery
G2 Engine
G3 Transmission housing
G101 A/T clutch pressure control solenoid valves A, B, C (A/T), CKP sensor, CMP sensor A, CMP sensor B, Data link connector (DLC), ECM/PCM (LG1), ECM/PCM (LG2), ECM/PCM (PG1), ECM/PCM (PG2), ECM/PCM (PGMETCS), EGR valve (K20Z2 engine), Ignition
coils, Immobilizer-keyless control unit, Rocker arm oil control solenoid, Rocker arm oil pressure switch, Transmission range
switch (A/T), VTC oil control solenoid valve
Shielding between the ECM/PCM and Knock sensor (KS) has wire.
Shielding between the ECM/PCM and Secondary HO2S (Sensor 2) has wire.
G201 Right fog light , Right front parking light, Right front side marker light, Right front turn signal light, Right headlight (high/low beams), Right HID unit , Windshield washer motor, Windshield wiper motor
G202 ABS modulator-control unit , VSA modulator-control unit
G301 A/C condenser fan motor, Blower motor relay, ELD, Left fog light , Left front parking light, Left front side marker light, Left front turn signal light, Left headlight (high/low beams), Left HID unit , Radiator fan motor (via fan control relay)
G401 Brake fluid level switch, Clutch interlock switch (M/T), Clutch pedal position switch (M/T), Hood switch, MICU (PG), Power transistor, Washer fluid level switch (G401 connects to G601 via under-dash fuse/relay box)
G402 EPS control unit
G403 Torque sensor
G501 Dash lights brightness controller and odometer select/reset switch, Driver’s door key cylinder switch, Driver’s door lock knob switch, HandsFreeLink control unit , MICU (SG), VSA OFF switch
G502 Data link connector (DLC), Front accessory power socket, Glove box light, Right power mirror defogger, Right side turn signal light
G503 Accessory power socket relays (front and console), Driver’s door lock switch, Gauge control module (tach), Left power mirror defogger, Left side turn signal light, Moonroof control unit/motor, Power mirror switch light, Power mirror switch, Power
window master switch (main switch), Power window master switch, Vanity mirror lights (driver’s and front passenger’s)
G504 Cable reel (steering wheel switches ground), Climate control unit, Front passenger’s door lock knob switch, Front passenger’s door lock switch, Gauge control module (speedo), Gauge control module (tach), Ignition key switch, Navigation unit , TPMS
control unit
G505 Audio unit , Navigation unit
G506 Memory erase signal (MES) connector, SRS unit (2 wires)
G601 A/T gear position console panel light/Park-pin switch (A/T), Console accessory power socket , Fuel pump, MICU (PG), Seat heater relays (driver’s and front passenger’s), Seat heater switches (driver’s and front passenger’s), Seat heaters (driver’s and
front passenger’s), Stereo amplifier (G601 connects to G401 via under-dash fuse/relay box)
Shielding between the left side impact sensor (FIRST) and rear safing sensor has wire.
Shielding between the SRS unit and left side impact sensor (FIRST) has wire.
G602 Driver’s seat belt buckle switch, Front passenger’s seat belt buckle switch, Left rear door lock knob switch, MICU (SG), MICU service check connector, ODS unit, Right rear door lock knob switch, Yaw rate-lateral acceleration sensor
Shielding between the right side impact sensor (FIRST) and right side impact sensor (SECOND) have wires.
Shielding between the SRS unit and right side impact sensor (FIRST) has wire.
G603 Noise condenser Shielding between the rear safing sensor and left side impact sensor (SECOND) has wire.
G701 High mount brake light, Left back-up light, Left inner taillight, Left rear side marker light, Left rear turn signal light, Left taillight/ brake light, License plate lights, Right back-up light, Right inner taillight, Right rear side marker light, Right rear turn signal light,
Right taillight/brake light, Trunk lid release actuator/Trunk lid latch switch
G801 Rear window defogger ( )
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S and ’08 premium and ’09 models
5: With HID
6: Without navigation system
7: With navigation system
8: ’09 model with navigation system
9: ’06-08 models, and ’09 model without navigation system
10: TYPE S model
4
512 4
5
82 3
7
3
67
9
10
2
08/08/21 14:24:03 61SNR030_220_0066
ProCarManuals.com
DYNOMITE -2009-

(#'
) MICUDTC Description DTC typePage
22-77
DTC Troubleshooting Index
NOTE: Check the ECM/PCM for DTCs and troubleshoot ECM/PCM (see page 11-3) or F-CAN loss of communication
errors first, then record all DTCs, and sort them by DTC type using the DTC troubleshooting index, then troubleshoot
the DTC(s) in this order.
 Battery voltage DTCs
 Internal error DTCs
 Loss of communication DTCs (beginning with the lowest number first; for example, if B1008 and B1011 are retrieved, troubleshoot B 1008 first).
 Signal error DTCs
B1000 Communication bus line error (BUS-OFF) Loss of communication(see page 22-102)
B1001 MICU internal error (CPU error) (’06-08 models) Internal error (see page 22-103)
B1002 MICU internal error ( EEPROM error) Internal error (see page 22-103)
B1008 MICU lost communication with gauge control m odule (A/T
message) Loss of
communication(see page 22-104)
B1011 MICU lost communication with gauge control m odule (VSP/NE
message) Loss of
communication(see page 22-104)
B1026 Front passenger’s door lock switch LOCK/UNLOCK signal error Signal error (see page 22-120)
B1032 MICU lost communication with the SRS unit (CDS message) CDS (Collision detection signal) input circuit malfunction (’06-07
models) Signal error (see page 22-105)
B1036 IG1 line input error Signal error (see page 22-105)
B1077 Windshield wiper (As) signal error Signal error (see page 22-224)
B1078 Daytime r unning lights signal error Signal error (see page 22-157)
B1127 Driver’s door key cylinder switch signal error Signal error (see page 22-121)
B1128 Driver’s door lock switch signal error Signal error (see page 22-123)
B1129 Driver’s door lock knob switch signal error Signal error (see page 22-124)
B1275 Combination light switch OFF position circuit malfunction (’07- 09 models) Signal error (see page 22-159)
B1276 Combination light switch parking (SMALL) position circuit malfunction (’07-09 models) Signal error (see page 22-159)
B1278 Headlight switch ON position circuit malfunction (’07-09 models) Signal error (see page 22-159)
B1279 Headlight switch DIMMER position circuit malfunction (’07-09 models) Signal error (see page 22-161)
B1280 Turn signal switch circuit malfunction (’07-09 models) Signal error (see page 22-186)
B1281 Windshield wiper switch MIST position circuit malfunction (’07- 09 models) Signal error (see page 22-226)
B1282 Windshield wiper switch INT position circuit malfunction (’07-09 models) Signal error (see page 22-226)
B1283 Windshield wiper switch LOW position circuit malfunction (’07- 09 models) Signal error (see page 22-226)
B1284 Windshield wiper switch HIGH position circuit malfunction (’07- 09 models) Signal error (see page 22-226)
(cont’d)
08/08/21 14:24:07 61SNR030_220_0079
ProCarManuals.com
DYNOMITE -2009-

MICU Control Functions Index
SystemFunction
22-82Multiplex Integrated Control System
System Description (cont’d)
The MICU (built into the under-dash fuse/relay box) is one of the B-CAN components. The MICU controls many
systems related to the body controller area and security system, and also works as a gateway to the diagnose the
other B-CAN connected ECUs with the HDS.
Refer to the each system circuit diagram in detail.
Multiplex Control Sends the switch input signal information to the MICU and outputs the information. The MICU controls the ECUs electric load and communication based upon the information
received the B-CAN.
On-Board Diagnosis The MICU has a gateway function which sends the results of the MICU internal diagnosis and the B-CAN connected ECUs diagnosis to the HDS.
Self-Diagnosis Test mode 1 diagnoses the communication line between the MICU and B-CAN connected unit. Test mode 2 checks the switch inputs connected to the MICU.
Interior Light(s) The MICU controls the interior lights ON, OFF and dimming based upon the information of the related switches and/or the B-CAN related information.
Sleep Function The MICU has a sleep function, which it enters during the power down mode.
The MICU also controls the function of these circuits:  Entry lights control (map lights and ceiling light)
 Exterior lights control (including the daytime running lights control)
Horn
 Interlock system
 Key-in reminder
 Keyless entry
 Lights-on reminder
 Power door locks
 Power window key-off timer
 Seat belt reminder
 Security alarm
 Turn signal/hazard flasher
 Wiper/washer
08/08/21 14:24:08 61SNR030_220_0084
ProCarManuals.com
DYNOMITE -2009-