maintenance reset ACURA CSX 2006 Service Repair Manual


(#')
Information Display
Driver’s Side Dashboard:
3-4Maintenance Minder
General Information
MAINTENANCE MINDER INDICATOR
INFORMATION DISPLAY
SEL/RESET BUTTON
The maintenance minder is an important feature of the information display. Based on engine and transmission
operating conditions, the Acura CSX’s onboard computer (ECM/PCM) calculates the remaining engine oil and the
automatic transmission fluid life. The system also displays the remaining engine oil life along with the code(s) for
other scheduled maintenance items needing service.
08/08/21 14:08:30 61SNR030_030_0004
ProCarManuals.com
DYNOMITE -2009-

µµ










Service Information
3-5
A
C D
A
B A
A
1. The remaining engine oil life (A) is shown as apercentage on the information display. To see the
current engine oil life, turn the ignition switch to
ON (II), then push and release the SEL/RESET
button repeatedly until the engine oil life displays.
2. When the ignition switch is ON (II), and the remaining engine oil life is 6 % to 15 %, the
remaining engine oil life (A) and other scheduled
maintenance item(s) needing service are displayed.
The maintenance minder indicator (B) also comes
on when the engine oil life is 15 % or less. To
cancel the display and the indicator, press SEL/
RESET button.
 Complete list of maintenance main items (C) (see page 3-7).
 Complete list of maintenance sub items (D) (see page 3-8). 3. When the ignition switch is ON (II), and the
remaining engine oil life is 1 % to 5 %, the message
‘‘SERVICE’’ (A) is displayed along with engine oil
life and the same maintenance item code(s).
4. When the ignition switch is ON (II), and the remaining engine oil life is 0 %, the engine oil life
indicator (A) blinks. Pressing SEL/RESET button
cancels the display, but the maintenance minder
indicator stays on.
5. If the indicated maintenance is not done, the engine oil life indicator shows a negative mileage, for
example ‘‘ 10,’’ on the display. If the negative
mileage is between 0 and 9, the indicator is
displayed for only a few seconds when the ignition
switch is turned to ON (II). The negative mileage
remains displayed after the vehicle is driven more
than 10 km after 0 % oil life is reached, and the
display cannot be canceled.
This means the indicated maintenance item(s)
should have been done more than 10 km ago.
(cont’d)
08/08/21 14:08:31 61SNR030_030_0005
ProCarManuals.com
DYNOMITE -2009-



Resetting Maintenance Information Display Resetting Individual Maintenance Items
3-6Maintenance Minder
General Information (cont’d)
NOTE:
 The vehicle must be stopped to reset the display.
 If a required service is done and the display is not reset, or the maintenance display is reset without
doing the service, the system will not show the
proper maintenance timing. This can lead to serious
mechanical problems because there will be no
accurate record of when the required maintenance is
needed.
 The engine oil life and the maintenance item(s) can be only reset independently with the HDS.
1. Turn the ignition switch to ON (II).
2. Push and release the SEL/RESET button repeatedly until the engine oil life indicator is displayed.
3. Press and hold the SEL/RESET button for about 10 seconds. The engine oil life indicator and the
maintenance item code(s) will blink, then release
the button.
NOTE: If you are resetting the display when the
engine oil life is more than 15 %, make sure the
maintenance item(s) requiring service are done
before resetting the display.
4. Press and hold the SEL/RESET button for another 5 seconds. The maintenance item code(s) will
disappear, and the engine oil life will reset to ‘‘100’’. 1. Connect the Honda Diagnostic System (HDS) to the
data link connector (DLC) (see step 2 on page 11-3).
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module/powertrain control
module (ECM/PCM). If it doesn’t communicate,
troubleshoot the DLC circuit (see page 11-6).
4. Select GAUGES in the BODY ELECTRICAL with the HDS.
5. Select ADJUSTMENT in the GAUGES with the HDS.
6. Select SERVICE REMINDER in the ADJUSTMENT with the HDS.
7. Select RESET in the SERVICE REMINDER with the HDS.
8. Select the individual maintenance item you wish to reset.
08/08/21 14:08:32 61SNR030_030_0006
ProCarManuals.com
DYNOMITE -2009-

(#')Symbol Maintenance Main Items
3-7
Maintenance Main Items
If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every
year.
NOTE:


 Replace the brake fluid every 3 years independent of the maintenance messages in the information display.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2 or 3, only if they are noisy.

















A Replace engine oil (see page 8-10).
Engine oil capacity without oil filter:
K20Z2: 4.0 L (4.2 US qt)
K20Z3: 4.2 L (4.4 US qt)
B Replace engine oil and oil filter (see page 8-11). Engine oil capacity with oil filter:
K20Z2: 4.2 L (4.4 US qt)
K20Z3: 4.4 L (4.6 US qt)
Check front and rear brakes (see page 19-3). Check pad and disc for wear (thickness), damage, and cracks.
Check calipers for damage, leaks, and tightness of mounting bolts.
Check parking brake adjustment (see page 19-7). Check the number of clicks (8 to 10) when the parking brake lever is pulled with 196 N (20 kgf,
44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see page 17-5). Check steering linkage.
Check boots for damage and leaking grease.
Check fluid lines for damage and leaks.
Inspect suspension components (see page 18-3). Check bolts for tightness.
Check condition of ball joint boots for deterioration and damage.
Inspect driveshaft boots (see page 16-4). Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA lines (see page 19-37). Check the master cylinder and VSA modulator-control unit for damage or leakage.
Inspect all fluid levels and condition of fluids. Engine coolant (see page 10-7)
Automatic transmission fluid (ATF-Z1) (see page 14-231)
Manual transmission fluid (MTF)
5M/T (see page 13-5), 6M/T (see page 13-82)
Clutch fluid (see page 12-7)
Brake fluid (see page 19-9)
Windshield washer fluid (see page 22-234)
Inspect exhaust system: K20Z2 (see page 9-13), K20Z3 (see page 9-14)
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.
Inspect fuel lines (see page 11-326) and connections (see page 11-328). Check for loose connections, cra cks, and deterioration; retighten loose connections and replace
damaged parts.
NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk ( ) will
not void the client’s emissions warranties. However, Acura recommends that all maintenance services be done at the
recommended interval, to ensure long-term reliability.
08/08/21 14:08:32 61SNR030_030_0007
ProCarManuals.com
DYNOMITE -2009-

10-9
8. Loosely install the radiator cap.
9. Set the heater temperature control dial tomaximum heat.
10. Start the engine, and let it run until it warms up (the radiator fan comes on at least twice).
11. Turn off the engine. Check the level in the radiator, and add Honda Long Life Coolant/Antifreeze
Type 2, if needed.
12. Install the radiator cap securely, then start the engine again, and check for leaks.
13. Clean up any spilled engine coolant.
14. If the maintenance minder required engine coolant replacement, reset the maintenance minder
(see page 3-6), and this procedure is complete. If
the maintenance minder did not require engine
coolant replacement, go to step 15.
15. Turn the ignition switch to LOCK (0).
16. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
17. Turn the ignition switch to ON (II).
18. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain
control module (PCM). If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
19. Select GAUGES in the BODY ELECTRICAL menu with the HDS.
20. Select ADJUSTMENT in the GAUGES with the HDS.
21. Select SERVICE REMINDER in the ADJUSTMENT menu with the HDS.
22. Select RESET in the SERVICE REMINDER menu with the HDS.
23. Select MAINTENACE SUB ITEM 5 RESET menu with the HDS.
08/08/21 14:39:59 61SNR030_100_0009
ProCarManuals.com
DYNOMITE -2009-


(#'
") 
(#'
 )
K20Z2 engine
11-34611-346 Intake Air System
Air Cleaner Element Inspection/
Replacement
Intake Air Resonator Removal/
Installation
A
B
C
D
E B
C
A
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
1. Open the air cleaner housing cover (A).
2. Remove the air cleaner element (B) from the air
cleaner housing (C).
3. Check the air cleaner element for damage or clogging. If it is damaged or clogged, replace it.
NOTE: Do not use compressed air to clean the air
cleaner element.
4. Clean and remove any debris from inside the air cleaner housing.
5. Install the parts in the reverse order of removal.  If you did not replace the air cleaner element, thisprocedure is complete.
 If the maintenance minder required air cleaner element replacement, reset the maintenance
minder(seepage3-7).
 If you replaced the air cleaner element, reset the ECM/PCM (see page 11-4), and do the ECM/PCM
idle learn procedure (see page 11-310). 1. Remove the front bumper (see page 20-146).
2. Remove the bolts (A), and pipe (B).
3. Remove the intake air resonator (C).
4. Do the battery removal procedure (see page 22-69).
5. Remove the bolt (D), and duct (E).
6. Install the parts in the reverse order of removal.
7. Do the battery installation procedure (see page
22-69).
08/08/21 14:31:09 61SNR030_110_0346
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#'


")
Fluid Capacity
1.5 L (1.6 US qt) at fluid change
1.7 L (1.8 US qt) at overhaul
13-5
Transmission Fluid Inspection and Replacement
A B
C
C
44 N·m
(4.5 kgf·m,
33 lbf·ft)
A
39 N·m
(4.0 kgf·m,
29 lbf·ft)
B D
1. Raise the vehicle on a lift.
2. Remove the filler plug (A) and the sealing washer
(B). Check the condition of the MTF, and make sure
it is at the proper level (C).
3. If the MTF is dirty, remove the drain plug (A) and the sealing washer (B), and drain it.
4. Install the drain plug with a new sealing washer, and refill the transmission with MTF to the proper
level. Always use Acura Manual Transmission Fluid
(MTF).
5. Install the filler plug (C) with a new sealing washer (D). 6. If the maintenance minder required to replace the
MTF, reset the maintenance minder (see page 3-4).
If it did not reset, go to step 7.
7. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
8. Turn the ignition switch to ON (II).
9. Make sure the HDS communicates with the vehicle and the engine control module (ECM). If it does not
communicate, go to the DLC circuit troubleshooting
(see page 11-204).
10. Select BODY ELECTRICAL with the HDS.
11. Select ADJUSTMENT in the GAUGES MENU with the HDS.
12. Select RESET in the MAINTENANCE MINDER with the HDS.
13. Select MAINTENANCE SUB ITEM 3, and reset the MTF life with the HDS.
Replace. Replace.
08/08/21 14:44:17 61SNR030_130_0007
ProCarManuals.com
DYNOMITE -2009-


Î
(#'


")
Fluid Capacity
1.5 L (1.6 US qt) at fluid change
1.7 L (1.8 US qt) at overhaul
13-82Manual Transmission
Transmission Fluid Inspection and Replacement
A
C
B
C
44 N·m
(4.5 kgf·m,
33 lbf·ft)
A
39 N·m
(4.0 kgf·m,
29 lbf·ft)
B D
1. Raise the vehicle on a lift, and make sure it is
securely supported.
2. Remove the filler plug (A) and the sealing washer (B), check the condition of the MTF, and make sure
it is at the proper level (C).
3. If the MTF is dirty, remove the drain plug (A) and the sealing washer (B), and drain it.
4. Install the drain plug with a new sealing washer, and refill the transmission with MTF to the proper
level. Always use Acura Manual Transmission Fluid
(MTF).
5. Install the filler plug (C) with a new sealing washer (D). 6. If the maintenance minder required to replace the
MTF, reset the maintenance minder (see page 3-4).
If it did not reset, go to step 7.
7. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
8. Turn the ignition switch to ON (II).
9. Make sure the HDS communicates with the vehicle and the engine control module (ECM). If it does not
communicate, go to the DLC circuit troubleshooting
(see page 11-204).
10. Select BODY ELECTRICAL with the HDS.
11. Select ADJUSTMENT in the GAUGES MENU with the HDS.
12. Select RESET in the MAINTENANCE MINDER with the HDS.
13. Select MAINTENANCE SUB ITEM 3, and reset the MTF life with the HDS.
Replace. Replace.
08/08/21 14:47:17 61SNR030_130_0084
ProCarManuals.com
DYNOMITE -2009-

Î
 
(#'



 )
Automatic Transmission Fluid Capacity:
2.9 L (3.1 US qt) at change
6.5 L (6.9 US qt) at overhaul
14-232 Automatic Transmission
ATF Replacement
A
18 x 1.5 mm
49 N·m
(5.0 kgf·m,
36 lbf·ft)
B
ATF
A
NOTE: Keep all foreign particles out of the transmission. 1. Park the vehicle on the level ground.
2. Warm up the engine to normal operating temperature (the radiator fan comes on), and turn
the engine off.
3. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
4. Reinstall the drain plug with a new sealing washer (B).
5. Refill the transmission with ATF into the dipstick hole to bring the fluid level between the upper
mark and the lower mark of the dipstick. Always
use Acura ATF-Z1 automatic transmission fluid
(ATF). Using a non-Acura ATF can affect shift
quality.
6. Check that the ATF level is between the upper mark
and the lower mark of the dipstick.
7. Insert the dipstick back into the transmission with the letters ‘‘ATF’’ pointing toward the front of the
vehicle. 8. If the maintenance minder required to replace the
ATF, reset the maintenance minder (see page 3-4),
and this procedure is complete. If the maintenance
minder did not require you to replace the ATF, go
to step 9.
9. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
10. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go
to the DLC circuit troubleshooting (see page
11-204).
11. Select BODY ELECTRICAL with the HDS.
12. Select ADJUSTMENT in the GAUGES MENU with the HDS.
13. Select RESET in the MAINTENANCE MINDER MENU with the HDS.
14. Select RESETTING THE ATF with the HDS.
NOTE: If you changed the engine oil at the same
time with the ATF, select RESETTING THE ENGINE
OIL LIFE AND ATF with the HDS instead.
Replace.
08/08/21 14:46:53 61SNR030_140_0234
ProCarManuals.com
DYNOMITE -2009-

Entry Lights Control System
Power Windows
Wipers/Washers
GaugesReminder Systems
Moonroof
Accessory Power Sockets
Seat Heaters
Power Mirrors
Rear Window Defogger
Immobilizer System......................
.......................................... ......................................... ...........................
.............................. ......................
.......................................... ......................................... ...........................
..............................
Component Location Index . 22-202
Circuit Diagram . 22-203
MICU Input Test . 22-204
Ignition Key Switch Test . 22-207
Ignition Key Light Test . 22-207
......................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
........................................................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
..................................
Component Location Index
. 22-208
System Description . 22-209
Resetting the Power Window Control Unit . 22-210
Circuit Diagram . 22-212
Power Window Master Switch Input Test . 22-214
Driver’s Power Window Motor Test . 22-217
Passenger’s Power Window Motor Test . 22-218
Power Window Master Switch Test/Replacement . 22-219
Passenger’s Power Window Switch Test/Replacement . 22-220
......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
...................... ......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
......................
Component Location Index
. 22-221
Circuit Diagram . 22-223
DTC Troubleshooting . 22-224
MICU Input Test . 22-228
Wiper/Washer Switch Test . 22-231
Wiper Motor Test . 22-231
Washer Motor Test . 22-232
Washer Fluid Level Switch Test . 22-232
Wiper Motor Replacement . 22-233
Wiper/Washer Switch Replacement . 22-234
Washer Reservoir Replacement . 22-234
Wiper Blade Replacement . 22-235
Wiper Arm/Nozzle Adjustment . 22-236
Washer Tube Replacement . 22-237
......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
.............................................. ......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
..............................................
Component Location Index
. 22-238
Self-diagnostic Function . 22-241
Circuit Diagram . 22-244
DTC Troubleshooting . 22-262
Gauge Control Module (Tach) Input Test . 22-271
Gauge Control Module (Speedo) Input Test . 22-274
Rewriting the ODO Data and Transferring the Maintenance
Minder Data to a New Gauge
Control Module . 22-276
Replacement . 22-277
Dash Lights Brightness Controller and Odometer Select/Reset Switch
Test/Replacement . 22-278
Outside Air Temperature Indicator Calibration . 22-279 ......................
.......................................... ......................................... ......................
.......................................... .........................................
Component Location Index
. 22-281
Circuit Diagram . 22-282
MICU Input Test . 22-284
...................... ......
.......................................... ...................
......................
......
.......................................... ...................
Component Location Index
. 22-286
Resetting the Moonroof Control Unit . 22-287
Circuit Diagram . 22-288
Moonroof Control Unit Input Test . 22-290
Moonroof Switch Test/Replacement . 22-293
......................
..........................................
..................................
.................................. ......................
..........................................
..................................
..................................
Component Location Index
. 22-294
Circuit Diagram . 22-295
Front Accessory Power Socket Test/Replacement . 22-296
Console Accessory Power Socket Test/Replacement . 22-297
......................
.......................................... .........................
........................................ ......................
.......................................... .........................
........................................
Component Location Index
. 22-298
Circuit Diagram . 22-300
Switch Test/Replacement . 22-302
Seat Heater Test . 22-302
......................
..........................................
..............................................
........................................................ .......
......................
..........................................
..............................................
........................................................ .......
Component Location Index
. 22-304
Circuit Diagram . 22-305
Function Test . 22-306
Power Mirror Switch Test/Replacement . 22-307
Power Mirror Actuator Test . 22-307
Power Mirror Actuator Replacement . 22-308
......................
..........................................
.............................................. ......................................................
..........................................
.............................................. ................................
Component Location Index
. 22-310
Circuit Diagram . 22-311
Function Test . 22-312
Defogger Wire Repair . 22-313
......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ........................................... ......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ...........................................
Component Location Index
. 22-314
System Description . 22-315
Circuit Diagram . 22-316
DTC Troubleshooting . 22-317
Symptom Troubleshooting Information . 22-321
Symptom Troubleshooting . 22-323
System Check . 22-326
Status Log . 22-328
Immobilizer Key Registration . 22-329
Immobilizer-Keyless Control Unit Input Test . 22-330
Immobilizer-Keyless Control Unit Replacement . 22-332
08/08/21 14:22:03 61SNR030_220_0003
ProCarManuals.com
DYNOMITE -2009-