f-can ACURA CSX 2006 Service Repair Manual

(#'


/)
Fuel and Emissions
Fuel and Emissions Systems
PGM-FI System
Electronic Throttle Control System
VTEC/VTC
Idle Control SystemFuel Supply System
Intake Air System
Catalytic Converter System
EGR System
PCV System
EVAP System..................................................
........
......................... ................
....................................... .......................
..................................................
........
......................... ................
....................................... .......................
Special Tools . 11-2
General Troubleshooting Information . 11-3
DTC Troubleshooting Index . 11-9
Symptom Troubleshooting Index . 11-13
System Description . 11-15
How to Set Readiness Codes . 11-69
..........................
.................................... ....................
......................... ........................
.................................... .............................. ....................
........................
.............................
.............................................. .........................
............................ ........
..........................
..........................
..........................................
.......................................... ..........................................................
.................................... ....................
......................... ........................
.................................... .............................. ....................
........................
.............................
.............................................. .........................
............................ ........
..........................
..........................
..........................................
.......................................... ................................
Component Location Index . 11-72
DTC Troubleshooting . 11-74
F-CAN Circuit Troubleshooting . 11-191
MIL Circuit Troubleshooting . 11-203
DLC Circuit Troubleshooting . 11-204
Injector Replacement . 11-219
A/F Sensor Replacement . 11-221
Secondary HO2S Replacement . 11-221
CMP Sensor B Replacement . 11-222
CKP Sensor Replacement . 11-222
Output Shaft (Countershaft) Speed Sensor
Replacement . 11-223
Knock Sensor Replacement . 11-223
MAP Sensor Replacement . 11-224
MAF Sensor/IAT Sensor Replacement . 11-224
ECT Sensor 1 Replacement . 11-225
ECT Sensor 2 Replacement . 11-225
ELD Replacement . 11-226
ECM/PCM Update . 11-227
ECM/PCM Replacement . 11-228
..........................
.................................... ......................
................................. ..........................
.................................... ......................
.................................
Component Location Index . 11-231
DTC Troubleshooting . 11-232
APP Sensor Signal Inspection . 11-268
Accelerator Pedal Module
Removal/Installation . 11-269
..........................
....................................
.................................................
.................................
................................. ..........................
....................................
.................................................
.................................
.................................
Component Location Index
. 11-273
DTC Troubleshooting . 11-274
VTC Oil Control Solenoid Valve Removal/Test/Installation . 11-294
CMP Sensor A Replacement . 11-295
Rocker Arm Oil Control Valve Removal/Installation . 11-296
Rocker Arm Oil Pressure Switch Removal/Installation . 11-296
..........................
.................................... .............
........................................
........................................ .................................... ...................
..........................
.................................... .............
........................................
........................................ .................................... ...................
Component Location Index
. 11-297
DTC Troubleshooting . 11-298
A/C Signal Circuit Troubleshooting . 11-306
Alternator FR Signal Circuit Troubleshooting . 11-307
Brake Pedal Position Switch Signal Circuit Troubleshooting . 11-308
Idle Speed Inspection . 11-309
ECM/PCM Idle Learn Procedure . 11-310 ..........................
.................................... .............
................................
......................................... ........................................ ......................................
.................................................
...................................................... .................................................. ....
........
................................
.............................................. .....................................................
................................. ..........................
.................................... .............
................................
......................................... ........................................ ......................................
.................................................
...................................................... .................................................. ....
........
................................
.............................................. .....................................................
.................................
Component Location Index
. 11-311
DTC Troubleshooting . 11-313
Fuel Pump Circuit Troubleshooting . 11-318
Fuel Pressure Relieving . 11-322
Fuel Pressure Test . 11-325
Fuel Tank Draining . 11-325
Fuel Line Inspection . 11-326
Fuel Line/Quick-Connect Fitting Precautions . 11-328
Fuel Line/Quick-Connect Fitting Removal . 11-329
Fuel Line/Quick-Connect Fitting Installation . 11-331
Fuel Tank Unit Removal and Installation . 11-334
Fuel Pressure Regulator Replacement . 11-337
Fuel Filter Replacement . 11-337
Fuel Pump/Fuel Gauge Sending Unit Replacement . 11-338
Fuel Tank Replacement . 11-339
Fuel Gauge Sending Unit Test . 11-340
Low Fuel Indicator Test . 11-341
..........................
......................................... .................................
.............................................................. .................
........................... .
............. ....
.............................................. ..........................
......................................... .................................
.............................................................. .................
........................... .
............. ....
..............................................
Component Location Index
. 11-342
Throttle Body Test . 11-343
Throttle Body Cleaning . 11-344
Intake Air Bypass Control Thermal Valve Test . 11-344
Air Cleaner Removal/Installation . 11-345
Air Cleaner Element Inspection/Replacement . 11-346
Intake Air Resonator Removal/Installation . 11-346
Throttle Body Removal/Installation . 11-348
Throttle Body Disassembly/Reassembly . 11-350
Intake Air Bypass Control Thermal Valve Replacement . 11-351
..........................
.................................... ...
..........................
.................................... ...
Component Location Index
. 11-352
DTC Troubleshooting . 11-353
Catalytic Converter Removal/Installation . 11-355
..........................
.................................... .........................................................
.................................... ...............................
Component Location Index
. 11-356
DTC Troubleshooting . 11-357
EGR Valve Replacement . 11-370
..........................
.................................... .........................................................
.................................... ...............................
Component Location Index
. 11-371
PCV Valve Inspection . 11-372
PCV Valve Replacement . 11-373
..........................
....................................
........................................ ........................
.............................
..............................................
.............................................. ..........................
....................................
........................................ ........................
.............................
..............................................
..............................................
Component Location Index
. 11-374
DTC Troubleshooting . 11-375
Fuel Cap Warning Message System Troubleshooting . 11-405
EVAP Canister Replacement . 11-407
FTP Sensor Replacement . 11-408
EVAP Canister Vent Shut Valve Replacement . 11-409
EVAP Canister Purge Valve Replacement . 11-409
08/08/21 14:12:30 61SNR030_110_0001
ProCarManuals.com
DYNOMITE -2009-

Ó
•••
•••
••• ´
••• µ Ó
Ó
Ó
Ó
•••
•••
•••
•••
••• Ó
•••
•••
•••
•••
•••
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-12Fuel and Emissions Systems
DTC Troubleshooting Index (cont’d)
P2227 (13)
Barometric Pressure (BARO) Sensor Circuit Range/Performance
Problem ON (see page 11-176)
P2228 (13) Barometric Pressure (BARO) Sensor Circuit Low Voltage ON (see page 11-177)
P2229 (13) Barometric Pressure (BARO) Sensor Circuit High Voltage ON (see page 11-177)
P2238 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) AFS Circuit Low Voltage ON (see page 11-178)
P2252 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) AFS Circuit Low Voltage ON (see page 11-179)
P2270 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit Signal Stuck Lean ON (see page 11-181)
P2271 (63) Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2))
Circuit Signal Stuck Rich ON (see page 11-181)
P2413 (12) Exhaust Gas Recirculation (EGR) System Malfunction ON (see page 11-363)
P2422 (117) Evaporative Emission (EVAP) Canister Vent Shut Valve Stuck Closed
Malfunction ON (see page 11-402)
P2610 (132) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Ignition Off Internal Timer Malfunction ON (see page 11-182)
P2646 (22) Rocker Arm Oil Pressure Switch Circuit Low Voltage ON (see page 11-284)
P2647 (22) Rocker Arm Oil Pressure Switch Circuit High Voltage ON (see page 11-287)
P2648 (21) Rocker Arm Oil Control Solenoid Circuit Low Voltage ON (see page 11-289)
P2649 (21) Rocker Arm Oil Control Solenoid Circuit High Voltage ON (see page 11-291)
P2A00 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Circuit Range/Performance
Problem ON (see page 11-182)
U0028 (126) F-CAN Malfunction (BUS-OFF (Engine Control Module (ECM)/
Powertrain Control Module (PCM))) ON (see page 11-183)
U0122 (126) F-CAN Malfunction (Engine Control Module (ECM)/Powertrain
Control Module (PCM)-Vehicle Stability Assist (VSA) Modulator-
Control Unit) OFF (see page 11-184)
U0131 (126) F-CAN Malfunction (Engine Control Module (ECM)/Powertrain
Control Module (PCM)-Electrical Power Steering (EPS) Control Unit) OFF (see page 11-186)
U0155 (126) F-CAN Malfunction (Engine Control Module (ECM)/Powertrain
Control Module (PCM)-Gauge Control Module) ON (see page 11-188)
U0300 (131) PGM-FI System and A/T System Program Version Mismatch ON (see page 11-190)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
1: A/T
4: K20Z2 engine
6: with VSA
4
6
1
08/08/21 14:12:36 61SNR030_110_0012
ProCarManuals.com
DYNOMITE -2009-

(#')
Electronic Control Systems
Self-diagnosisOne Drive Cycle Detection Method
Two Drive Cycle Detection Method
Fail-safe Function
MIL Bulb Check and Readiness Code Condition
Self Shut Down (SSD) Mode
11-15
System Description
The functions of the fuel and emission control systems are managed by the engine control module (ECM) on vehicles
with manual transmissions or the powertrain control module (PCM) on vehicles with automatic transmissions.
The ECM/PCM detects a failure of a signal from a sensor or another control unit and stores a Temporary DTC or a DTC.
Depending on the failure, a DTC is stored in either the first or the second drive cycle (K20Z3 engine: DTC P0457, turns
on the malfunction indicator lamp (MIL) during the third drive cycle). When a DTC is stored, the ECM/PCM turns on the
malfunction indicator lamp (MIL) by a signal sent to the gauge via F-CAN.  When an abnormality occurs in the signal from a sensor or from another control unit, the ECM/PCM stores a DTC
and turns on the MIL immediately.
 When an abnormality occurs in the signal from a sensor or from another control unit in the first drive cycle, the
ECM/PCM stores a Temporary DTC. If the failure continues in the second drive cycle, the ECM/PCM stores a DTC and
turns on the MIL.
When an abnormality occurs in the signal from a sensor or another control unit, the ECM/PCM ignores the signal and
substitutes a pre-programmed value that allows the engine to continue running. This causes a DTC to be stored and
the MIL to come on.
When the ignition switch is turned to ON (II), the ECM/PCM turns on the MIL via the F-CAN circuit for about 15 to
20 seconds to check the bulb condition. If any readiness codes are not set to complete, the MIL flashes five times. If all
readiness codes are set to complete, the MIL goes off.
After the ignition switch is turned to LOCK (0), the ECM/PCM stays on (about 30 minutes). If the ECM/PCM connector is
disconnected during this time, the ECM/PCM may be damaged. To cancel this mode, disconnect the negative cable
from the battery or jump the SCS line with the HDS after the ignition switch is turned to LOCK (0).
(cont’d)
08/08/21 14:12:37 61SNR030_110_0015
ProCarManuals.com
DYNOMITE -2009-

µ
µ µ
µ
(#' 
*)
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
DTC U0028:
11-18311-183
10. Do the ECM/PCM idle learn procedure (see page
11-310).
11. Test-drive under these conditions:  Engine coolant temperature (ECT SENSOR 1)above70°C(158°F)
 A/TinD,M/Tin3rd
 Vehicle speed between 44 88 km/h (22 55 mph) for 5 minutes
 Drive at a steady speed between 88 120 km/h (55 75 mph) for 10 seconds, then decelerate
(with the throttle fully closed) for 5 seconds
12. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the A/F sensor (Sensor 1) and the ECM/
PCM, then go to step 1.
Go to step 13.
13. Monitor the OBD STATUS for DTC P2A00 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 12,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the A/F sensor
(Sensor1)andtheECM/PCM,thengotostep1.If
the screen indicates EXECUTING, keep driving until
a result comes on. If the screen indicates OUT OF
CONDITION, go to step 11. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Check for Temporary DTCs or DTCs with the HDS.
Go to step 4.
Intermittent failure, the system is OK at this
time.
4. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
5. Turn the ignition switch to ON (II).
6. Check for Temporary DTCs or DTCs with the HDS.
If the ECM/PCM was updated, substitute a
known-good ECM/PCM (see page 11-7), then
recheck. If the ECM/PCM was substituted, go to
step 1.
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). If
any other Temporary DTCs or DTCs are indicated,
go to the indicated DTC’s troubleshooting.F-CAN Malfunction (BUS-OFF
(ECM/PCM))
Is DTC P2A00 indicated?
Does t he scr een i nd i cat e PASSE D? I s DT C U 0028 i nd i cat ed ?
I s DT C P0028 i nd i cat ed ?
08/08/21 14:21:46 61SNR030_110_0183
ProCarManuals.com
DYNOMITE -2009-


(#' 
*
)
µ
µ
µ
µ
µ
µ µ
µ
DTC U0122:
YES
NO
YES
NO
YES
NO YES
NO
11-184PGM-FI System
DTC Troubleshooting (cont’d)
CANH (WHT)
CANH (WHT) ECM/PCM CONNECTOR A (44P)
VSA MODULATOR-CONTROL
UNIT 37P CONNECTOR
F-CAN Malfunction (ECM/PCM-
VSA Modulator-Control Unit)
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Check for Temporary DTCs or DTCs with the HDS.
Go to the troubleshooting for DTC U 0028.
Go to step 3.
3. Clear the DTC with the HDS.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the VSA modulator-control unit and the ECM/
PCM.
5. Check for communication to the VSA system with the HDS.
Go to step 6.
Go to the DLC circuit troubleshooting
(see page 11-204).
6. Turn the ignition switch to LOCK (0).
7. Jump the SCS line with the HDS.
8. Disconnect the VSA modulator-control unit 37P connector (see page 19- 171).
9. Disconnect ECM/PCM connector A (44P). 10. Check for continuity between ECM/PCM connector
terminal A36 and VSA modulator-control unit 37P
connector terminal No. 15.
Go to step 11.
Repair open in the wire between the ECM/
PCM (A36) and the VSA modulator-control unit,
then go to step 12.
Terminal side of female terminals
Wire side of female terminals
Ar e DT C U 0028 and U 0122 i nd i cat ed at t he same time?
Is DTC U0122 indicated?
Does the HDS communicate with the V SAmod ul at or -cont r ol uni t ? Is there continuity?
08/08/21 14:21:46 61SNR030_110_0184
ProCarManuals.com
DYNOMITE -2009-



(#' 
*

)
µ
µ
µ
µ
µ
µ µ
µ
DTC U0131:
YES
NO
YES
NO
YES
NO YES
NO
11-186PGM-FI System
DTC Troubleshooting (cont’d)
ECM/PCM CONNECTOR A (44P)
CANH (WHT)
JUMPER WIRE
EPS CONTROL UNIT CONNECTOR D (28P) CANH (WHT)
F-CAN Malfunction (ECM/PCM-
EPS Control Unit)
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Check for Temporary DTCs or DTCs with the HDS.
Go to the troubleshooting for DTC U 0028.
Go to step 3.
3. Clear the DTC with the HDS.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the EPS control unit and the ECM/PCM.
5. Check that the HDS communicates with the EPS system.
Go to step 6.
Go to the DLC circuit troubleshooting
(see page 11-204).
6. Turn the ignition switch to LOCK (0).
7. Jump the SCS line with the HDS.
8. Disconnect EPS control unit connector D (28P) (see page 17-84).
9. Disconnect ECM/PCM connector A (44P) 10. Connect ECM/PCM connector terminal A36 to body
ground with a jumper wire.
11. Check for continuity between EPS control unit connector D (28P) terminal No. 1 and body ground.
Go to step 12.
Repair open in the wire between the ECM/
PCM (A36) and the EPS control unit, then go to step
14.
Terminal side of female terminals
Wire side of female terminals
Ar e DT C U 0028 and U 0131 i nd i cat ed at t he sametime?
Is DT C U0131 ind icated ?
Does the HDS communicate with the EPS controluni t ? I s t her e cont i nui t y ?
08/08/21 14:21:47 61SNR030_110_0186
ProCarManuals.com
DYNOMITE -2009-



(#' 
*
)
µ
µ
µ
µ
µ
µ
DTC U0155:
YES
NO
YES
NO
YES
NO
11-188PGM-FI System
DTC Troubleshooting (cont’d)
GAUGE CONTROL MODULE (TACH) 36P CONNECTOR
CANH (WHT)
JUMPER WIRE
ECM/PCM CONNECTOR A (44P)CANH (WHT)
F-CAN Malfunction (ECM/PCM-
Gauge Control Module)
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Check for Temporary DTCs or DTCs with the HDS.
Go to step 4.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the gauge control module (tach) and the ECM/
PCM.
4. Check for body electrical DTCs in the DTCs MENU with the HDS.
Go to step 5.
Do the gauge control module (tach) input test
(see page 22-271).
5. Turn the ignition switch to LOCK (0).
6. Jump the SCS line with the HDS.
7. Remove the gauge control module (tach) (see page 22-277).
8. Disconnect ECM/PCM connector A (44P). 9. Connect gauge control module (tach) 36P
connector terminal No. 1 to body ground with a
jumper wire.
10. Check for continuity between ECM/PCM connector terminal A36 and body ground.
Go to step 11.
Repair open in the wire between the ECM/
PCM (A36) and the gauge control module (tach),
then go to step 13.
Wire side of female terminals
Terminal side of female terminals
Is DTC U0155 indicated? I s DT C B1168, B1169, and / or B117 8 i nd i cat ed ? Is there continuity?
08/08/21 14:21:48 61SNR030_110_0188
ProCarManuals.com
DYNOMITE -2009-

µµ
µ

(#')
µ
µ
YES
NO
11-191
F-CAN Circuit Troubleshooting
ECM/PCM CONNECTOR A (44P)
CANL (RED)
CANH (WHT)
1. Turn the ignition switch to LOCK (0).
2. Jump the SCS line with the HDS.
3. Disconnect ECM/PCM connector A (44P), then
disconnect the HDS.
4. Measure the resistance between ECM/PCM connector terminals A36 and A37.
Go to step 41.
Go to step 5. 5. Disconnect the gauge control module (tach) 36P
connector (see page 22- 277).
6. Disconnect the ABS modulator-control unit 25P connector (see page 19-90) (or the VSA modulator-
control unit 37P connector (see page 19-171) and
the yaw rate-lateral acceleration sensor 4P
connector (see page 19-169)).
7. Disconnect SRS unit connector A (28P) (see page 24-203).
8. Disconnect EPS control unit connector D (28P) (see page 17-84).
9. With TPMS: Disconnect the TPMS control unit 20P connector (see page 18-75).
(cont’d)
Terminal side of female terminals
I s t her e about 95 116 ( w i t h ABS) or 91 111( w i t h V SA sy st em), or 88 107 ( w i t h V SAsy st em and T PM S)?
08/08/21 14:21:49 61SNR030_110_0191
ProCarManuals.com
DYNOMITE -2009-



µ
µ µ
µ
YES
NO
YES
NO
11-192PGM-FI System
F-CAN Circuit Troubleshooting (cont’d)
ECM/PCM CONNECTOR A (44P)
CANL (RED)
CANH (WHT)
ECM/PCM CONNECTOR A (44P)CANH (WHT)
JUMPER WIRE GAUGE CONTROL MODULE (TACH) 36P CONNECTOR
CANH (WHT)
10. Check for continuity between ECM/PCM connector terminals A36 and A37.
Repair short in the wires between ECM/PCM
connector terminals A36 and A37.
Go to step 11.
11. Connect ECM/PCM connector terminal A36 to body ground with a jumper wire. 12. Check for continuity between gauge control
module (tach) 36P connector terminal No. 1 and
body ground.
 WithVSAsystem:Gotostep13.
 Without VSA system: Go to step 14. Repair open in the wire between the ECM/
PCM (A36) and the gauge control module (tach).
Terminal side of female terminals
Terminal side of female terminals Wire side of female terminals
Is there continuity?
Is there continuity?
08/08/21 14:21:50 61SNR030_110_0192
ProCarManuals.com
DYNOMITE -2009-

Î

µ
µ
YES
NO
11-194 PGM-FI System
F-CAN Circuit Troubleshooting (cont’d)
ECM/PCM CONNECTOR A (44P)
JUMPER WIRE CANL (RED) CANL (RED)
GAUGE CONTROL MODULE (TACH) 36P CONNECTOR
15. Remove the jumper wire from ECM/PCM connector
A (44P).
16. Connect ECM/PCM connector terminal A37 to body ground with a jumper wire. 17. Check for continuity between gauge control
module (tach) 36P connector terminal No. 19 and
body ground.
 WithVSAsystem:Gotostep18.
 Without VSA system: Go to step 19. Repair open in the wire between the ECM/
PCM (A37) and the gauge control module (tach).
Terminal side of female terminals Wire side of female terminalsIs there continuity?
08/08/21 14:21:51 61SNR030_110_0194
ProCarManuals.com
DYNOMITE -2009-