seat memory ACURA CSX 2006 Service Repair Manual

µ
(#'   
     ) 
GroundComponent or Circuit Grounded
22-64Ground Distribution
Ground to Components Index
G1 Battery
G2 Engine
G3 Transmission housing
G101 A/T clutch pressure control solenoid valves A, B, C (A/T), CKP sensor, CMP sensor A, CMP sensor B, Data link connector (DLC), ECM/PCM (LG1), ECM/PCM (LG2), ECM/PCM (PG1), ECM/PCM (PG2), ECM/PCM (PGMETCS), EGR valve (K20Z2 engine), Ignition
coils, Immobilizer-keyless control unit, Rocker arm oil control solenoid, Rocker arm oil pressure switch, Transmission range
switch (A/T), VTC oil control solenoid valve
Shielding between the ECM/PCM and Knock sensor (KS) has wire.
Shielding between the ECM/PCM and Secondary HO2S (Sensor 2) has wire.
G201 Right fog light , Right front parking light, Right front side marker light, Right front turn signal light, Right headlight (high/low beams), Right HID unit , Windshield washer motor, Windshield wiper motor
G202 ABS modulator-control unit , VSA modulator-control unit
G301 A/C condenser fan motor, Blower motor relay, ELD, Left fog light , Left front parking light, Left front side marker light, Left front turn signal light, Left headlight (high/low beams), Left HID unit , Radiator fan motor (via fan control relay)
G401 Brake fluid level switch, Clutch interlock switch (M/T), Clutch pedal position switch (M/T), Hood switch, MICU (PG), Power transistor, Washer fluid level switch (G401 connects to G601 via under-dash fuse/relay box)
G402 EPS control unit
G403 Torque sensor
G501 Dash lights brightness controller and odometer select/reset switch, Driver’s door key cylinder switch, Driver’s door lock knob switch, HandsFreeLink control unit , MICU (SG), VSA OFF switch
G502 Data link connector (DLC), Front accessory power socket, Glove box light, Right power mirror defogger, Right side turn signal light
G503 Accessory power socket relays (front and console), Driver’s door lock switch, Gauge control module (tach), Left power mirror defogger, Left side turn signal light, Moonroof control unit/motor, Power mirror switch light, Power mirror switch, Power
window master switch (main switch), Power window master switch, Vanity mirror lights (driver’s and front passenger’s)
G504 Cable reel (steering wheel switches ground), Climate control unit, Front passenger’s door lock knob switch, Front passenger’s door lock switch, Gauge control module (speedo), Gauge control module (tach), Ignition key switch, Navigation unit , TPMS
control unit
G505 Audio unit , Navigation unit
G506 Memory erase signal (MES) connector, SRS unit (2 wires)
G601 A/T gear position console panel light/Park-pin switch (A/T), Console accessory power socket , Fuel pump, MICU (PG), Seat heater relays (driver’s and front passenger’s), Seat heater switches (driver’s and front passenger’s), Seat heaters (driver’s and
front passenger’s), Stereo amplifier (G601 connects to G401 via under-dash fuse/relay box)
Shielding between the left side impact sensor (FIRST) and rear safing sensor has wire.
Shielding between the SRS unit and left side impact sensor (FIRST) has wire.
G602 Driver’s seat belt buckle switch, Front passenger’s seat belt buckle switch, Left rear door lock knob switch, MICU (SG), MICU service check connector, ODS unit, Right rear door lock knob switch, Yaw rate-lateral acceleration sensor
Shielding between the right side impact sensor (FIRST) and right side impact sensor (SECOND) have wires.
Shielding between the SRS unit and right side impact sensor (FIRST) has wire.
G603 Noise condenser Shielding between the rear safing sensor and left side impact sensor (SECOND) has wire.
G701 High mount brake light, Left back-up light, Left inner taillight, Left rear side marker light, Left rear turn signal light, Left taillight/ brake light, License plate lights, Right back-up light, Right inner taillight, Right rear side marker light, Right rear turn signal light,
Right taillight/brake light, Trunk lid release actuator/Trunk lid latch switch
G801 Rear window defogger ( )
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S and ’08 premium and ’09 models
5: With HID
6: Without navigation system
7: With navigation system
8: ’09 model with navigation system
9: ’06-08 models, and ’09 model without navigation system
10: TYPE S model
4
512 4
5
82 3
7
3
67
9
10
2
08/08/21 14:24:03 61SNR030_220_0066
ProCarManuals.com
DYNOMITE -2009-

Î 
(#'          ) 
24-11
SRS
Component Location Index
SRS INDICATOR
SIDE AIRBAG
CUTOFF INDICATOR
CABLE REEL
DRIVER’S AIRBAG
FRONT PASSENGER’S AIRBAG
PASSENGER’S AIRBAG CUTOFF INDICATOR
SRS UNIT OPDS SENSOR/SEAT-BACK
FRONT PASSENGER’S
SIDE AIRBAG
FRONT PASSENGER’S
SEAT BELT TENSIONER RIGHT SIDE
IMPACT SENSOR
(FIRST)
ODS UNIT
FRONT PASSENGER’S WEIGHT SENSORS
DRIVER’S SEAT BELT TENSIONER
LEFT SIDE IMPACT SENSOR (FIRST)
DRIVER’S SEAT POSITION SENSOR
DRIVER’S SIDE AIRBAG
DATA LINK
CONNECTOR (DLC) MEMORY ERASE
SIGNAL (MES)
CONNECTOR (2P)
(YELLOW)
FRONT PASSENGER’S SEAT BELT
BUCKLE TENSIONER
DRIVER’S SEAT BELT BUCKLE TENSIONER
(cont’d)
Troubleshooting, page 24-181
Troubleshooting, page 24-183
Replacement, page 24-200
Replacement, page 24-188
Disposal, page 24-196
Replacement, page 24-189
Disposal, page 24-196
Troubleshooting, page 24-184
Bulb Test/Replacement, page 24-212
Replacement, page 24-203 Replacement, page 20-122
Replacement,page 24-191
Disposal, page 24-196
Replacement, page 24-4
Disposal,
page 24-196 Replacement,
page 24-204
Initialization, page 24-26
Calibration, page 24-27
Operation Check, page 24-28
Replacement, page 24-209
Replacement, page 24-207
Replacement, page 24-4
Disposal, page 24-196
Replacement, page 24-204
Operation Check, page 24-29
Replacement, page 24-211
Replacement, page 24-188
Disposal, page 24-196Replacement, page 24-6
Replacement, page 24-6
08/08/21 13:54:16 61SNR030_240_0011
ProCarManuals.com
DYNOMITE -2009-

  
SRS Unit, Front and Side Impact Sensors,
Driver’s Seat Position Sensor, Front
Passenger’s Weight Sensors and, Rear
Safing Sensor
24-15
NOTE: Some systems store data in memory that is lost
when the battery is disconnected. Before disconnecting
the battery, refer to Battery Terminal Disconnection and
Reconnection (see page 22-68).
 Turn the ignition switch to LOCK (0), disconnect the negative cable from the battery, then wait at least 3
minutes before starting installation or replacement of
the SRS unit, or disconnecting the connectors from
the SRS unit.
 Be careful not to bump or impact the SRS unit, the front impact sensors, the side impact sensors, or the
rear safing sensor whenever the ignition switch is in
ON (II), or for at least 3 minutes after the ignition
switch is turned to LOCK (0).
 During installation or replacement, be careful not to bump (by impact wrench, hammer, etc.) the area
around the SRS unit, the front impact sensors, the
side impact sensors, or the rear safing sensor. The
airbags could accidentally deploy and cause damage
or injury.  After a collision where the front airbag, the side
airbag, or a the seat belt tensioner, the seat belt
buckle tensioner deployed, go to Component
Replacement/Inspection after Deployment (see page
24-185). After a collision where an airbag did not
deploy, inspect for any damage or any deformation
on the SRS unit, the front impact sensors, the side
impact sensors, or the rear safing sensor. If there is
any damage, replace the SRS unit and/or the sensors.
 Do not disassemble the SRS unit, front impact sensors, side impact sensors, driver’s seat position
sensor, front passenger’s weight sensors or rear
safing sensor.
 Always install the SRS unit, driver’s seat position sensor, and all impact sensors and the rear safing
sensor securely with new TORX bolts torqued to 9.8
N·m (1.0 kgf·m, 7.2 lbf·ft).
 Do not spill water or oil on the SRS unit or the any of the sensors, and keep them away from dust.
(cont’d)
08/08/21 13:54:19 61SNR030_240_0015
ProCarManuals.com
DYNOMITE -2009-

 
(#'   
        ) 
DTC (Diagnostic Trouble Codes) Reading the DTC
Precautions
24-22SRS
General Troubleshooting Information
A
The self-diagnostic function of the SRS system allows it
to locate the causes of system problems and store this
information in memory. For easier troubleshooting, this
data can be retrieved via a data link circuit.
 When you turn the ignition switch to ON (II), the SRS indicator comes on. If it goes off after 6 seconds, the
system is normal, and is not currently detecting any
abnormality.
 If there is an abnormality, the system locates and defines the problem, stores this information in
memory, and turns on the SRS indicator. The data
remains in memory even if the ignition switch is
turned off or the battery is disconnected.
 The data is stored in memory as a diagnostic trouble code (DTC).
 The ‘‘x’’ at the end of each DTC denotes a numeric character (0 thru 9) or an alpha character (A thru F)
that is displayed on the HDS.
 DTCs are either latching or resetting depending on the malfunction. With resetting DTCs, the SRS
indicator goes off the next time the ignition switch is
turned to ON (II), and the system is normal, but the
DTC is still stored. With latching DTCs, the SRS
indicator does not turn to LOCK (0) until the
malfunction is repaired and the DTC is cleared.
 When you connect the HDS to the data link connector (DLC), you can retrieve a more detailed DTC in the
HDS ‘‘SRS’’ menu.
NOTE: Only read DTCs from the SRS menu, not from
the SWS menus. SWS (ODS unit) DTCs are subcodes
of SRS unit DTCs. Only troubleshoot the
corresponding SRS DTCs.
 After reading and recording the DTC, proceed with the troubleshooting procedure for that code.
 Use only a digital multimeter to check the system. Make sure its output is 10 mA (0.01 A) or less when
switched to the smallest value in the ohmmeter range.
A tester with a higher output could damage the
airbag circuit or cause accidental airbag deployment
and possible injury.  Whenever the ignition switch is in ON (II), or has been
turned to LOCK (0), for less than 3 minutes, be careful
not to bump the SRS unit; the airbags could
accidentally deploy and cause damage or injuries.
 Before removing the dashboard wire harness, floor wire harness, disconnect the driver’s airbag
connector, the front passenger’s airbag connector,
both side airbag connectors, both side curtain airbag
connectors and both seat belt tensioner connectors.
 Make sure the battery is fully charged. If the battery is dead or low, electrical measurements may not be
correct.
 Do not touch a tester probe to the terminals in the SRS unit or harness connectors, and do not connect
the SRS unit terminals or the sensor terminals with a
jumper wire. Use only the backprobe set and the
multimeter. Backprobe spring-loaded lock type
connectors correctly.
1. Make sure the ignition switch is in LOCK (0).
2. Connect the HDS to the data link connector (DLC) (A).
3. Turn the ignition switch to ON (II).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
08/08/21 13:54:21 61SNR030_240_0022
ProCarManuals.com
DYNOMITE -2009-

 
(#'      
) 
24-26SRS
ODS Unit Initialization
A
When a seat-back cover, seat-back cushion, and/or ODS
unit is replaced, initialize the ODS by following the
procedure.
NOTE: A new (uninitialized) ODS unit installed with a
faulty OPDS sensor can cause DTC 85-71.
1. Clear the DTC memory (see page 24-23).
2. Make sure the front passenger’s seat is dry. Set the seat-back in a normal position, and make sure there
is nothing on the seat.
3. Make sure the ignition switch is in LOCK (0) and the MES connector is not shorted.
4. Connect the HDS to the data link connector (DLC) (A). 5. Turn the ignition switch to ON (II).
6. Make sure the HDS communicates with the vehicle
and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
7. From the HDS Main Menu, select SRS, then SRS, then Calibration. In the Calibration Menu, select
ODS INITIALIZATION. Follow the screen prompts to
initialize the ODS unit.
8. Turn the ignition switch to LOCK (0).
9. Disconnect the HDS from the DLC. NOTE: If the ODS unit fails to initialize after several
attempts, replace the OPDS sensor/seat-back and
retry. If the ODS unit continues to fail to initialize,
replace the ODS unit (see page 24-209).
08/08/21 13:54:22 61SNR030_240_0026
ProCarManuals.com
DYNOMITE -2009-

 
µ
´
Self-diagnostic System
24-37
GAUGE CONTROL MODULE CAN
CAN
MICROPROCESSOR and DIAGNOSTIC CIRCUIT
SRS UNIT
IMPACT GND TRIGGER CIRCUIT
SCS
MES
DLC
VA VB
ODS UNIT
FRONT
PASSENGER’S SEAT
OPDS
SENSOR RIGHT
SIDE IMPACT
SENSOR
(SECOND)
REAR
SAFING
SENSOR
FRONT
PASSENGER’S
SEAT BELT
BUCKLE
TENSIONER
CABLE
REEL
DRIVER’S
AIRBAG
FIRST
INFLATOR
DRIVER’S
AIRBAG
SECOND
INFLATOR FRONT
PASSENGER’S
AIRBAG
SECOND
INFLATOR
FRONT
PASSENGER’S
AIRBAG
FIRST
INFLATOR
SRS
INDICATOR
SIDE AIRBAG
CUTOFF
INDICATOR
DRIVER’S
SEAT BELT
BUCKLE
TENSIONER
FRONT
PASSENGER’S
SEAT BELT
TENSIONER
DRIVER’S
SEAT BELT
TENSIONER
RIGHT SIDE
CURTAIN
AIRBAG
INFLATOR
LEFT SIDE
CURTAIN
AIRBAG
INFLATOR
DATA
LINK
CIRCUIT
MEMORY
CIRCUIT
SIDE
IMPACT
SENSOR FRONT
IMPACT
SENSOR POWER
SUPPLY
CIRCUIT LEFT
FRONT
IMPACT
SENSOR
RIGHT
FRONT
IMPACT
SENSOR LEFT
SIDE IMPACT
SENSOR
(FIRST)
RIGHT
SIDE IMPACT
SENSOR
(FIRST)DRIVER’S
SIDE AIRBAG
INFLATOR
FRONT
PASSENGER’S
SIDE AIRBAG
INFLATOR
UNDER-DASH
FUSE/RELAY
BOX LEFT
SIDE IMPACT
SENSOR
(SECOND)
FRONT
PASSENGER’S
WEIGHT
SENSORS
FRONT
PASSENGER’S
AIRBAG
CUTOFF
INDICATOR
DRIVER’S SEAT
POSITION
SENSOR
A self-diagnostic circuit is built into the SRS unit; when the ignition switch is turned to ON (II), the SRS indicator comes
on and goes off after about 6 seconds if the system is operating normally.
If the indicator does not come on, or does not go off after 6 seconds, or comes on while driving, it indicates an
abnormality in the system. The system must be inspected and repaired as soon as possible.
For better serviceability, the SRS unit memory stores a DTCs related to the cause of the malfunction, and the unit is
connected to the data link connector (DLC). This information can be read with the HDS when it is connected to the DLC
(see page 24-22).
NOTE: Before you disconnect the negative cable from battery for troubleshooting, review Battery Terminal
Disconnection and Reconnection (see page 22-68).
(cont’d)
08/08/21 13:55:34 61SNR030_240_0037
ProCarManuals.com
DYNOMITE -2009-

Î (#'         )  ’06 model
24-40SRS
Circuit Diagram
GRN
BLU YEL
214 Q
E
G504
G602
BLK
LT GRN*
BLK*
BLK*
ORN*
LT BLU*
WHT*
RED* BLU*RED*
YEL*
2 1
G506 5
22
23 13 BLU
MICURED
2
4 MICU
GRY
YEL YEL
3
1
17 Vs
Vo
Vs
Vo
Vs
Vo
Vs
Vo BLU
BRN
5
10 15
GRY
123 3 21
LT GRN
16
11 6
GRY
BLU
GRN RED
4
914
WHT
123
321
BLK
13
83
RED
BRN MAIN CIRCUIT
VB
VA
WHT
GAUGE CONTROL MODULE (TACH)
BLK
412 SRS UNIT
ODS UNIT
7112 No. 9
(7.5 A) (7.5 A)
No. 10
No. 11
(10 A)
8
9 41
BRN
BLK
YEL
BLU GRN J
BATTERY
BAT
IG1
IGNITION SWITCH
UNDER-DASH FUSE/RELAY BOX
BLK
GRN
WHT BRN
A17
DRIVE CIRCUIT DRIVE CIRCUIT F-CAN TRANSCEIVER
16 1 19 WHT RED
A
A6
24
ORN
LT BLU
A
11 12 17 18
UNDER-HOOD
FUSE/RELAY BOX
DATA LINK
CONNECTOR
(DLC)
JUNCTION
CONNECTOR
JUNCTION
CONNECTOR
SEAT BELT
REMINDER
INDICATOR
SIDE
AIRBAG
CUTOFF
INDICATOR
SRS
INDICATORJUNCTION
CONNECTOR
To
SRS
UNIT ODS
UNIT
HARNESS OPDS
SENSOR
JUNCTION
CONNECTOR DASHBOARD
WIRE
HARNESS
FRONT
PASSENGER’S
WEIGHT
SENSOR
(FRONT
INNER
SIDE) FRONT
PASSENGER’S
WEIGHT
SENSOR
(REAR
INNER
SIDE) FRONT
PASSENGER’S
WEIGHT
SENSOR
(FRONT
OUTER
SIDE)FRONT
PASSENGER’S
WEIGHT
SENSOR
(REAR
OUTER
SIDE)
DASHBOARD
WIRE
HARNESS
FLOOR
WIRE
HARNESS
DASHBOARD
WIRE
HARNESS
PASSENGER’S
AIRBAG CUTOFF
INDICATOR
JUNCTION
CONNECTOR
MEMORY
ERASE
SIGNAL
(MES)
CONNECTOR
(2P)
FRONT
PASSENGER’S
SEAT
WIRE
HARNESS
(With
seat heater)
C783 C782
18P CAN
HI
CAN
LO
K-LINE SCS MES
SRS
GND (2)
SRS
GND (1)
a
08/08/21 13:55:35 61SNR030_240_0040
ProCarManuals.com
DYNOMITE -2009-

Î (#'         )  ’07-09 models
24-44SRS
Circuit Diagram (cont’d)
GRN
BLU YEL
124 Q
E
G504
G602
BLK
LT GRN*
BLK*
BLK*
ORN*
LT BLU*
WHT*
RED* BLU*RED*
YEL*
2 1
G506 5
22
23 13 BLU
MICURED
2
4 MICU
GRY
YEL
3
1
17 Vs
Vo
Vs
Vo
Vs
Vo
Vs
Vo BLU
BRN
5
10 15
GRY
123 3
21
LT GRN
16
11 6
GRY
BLU
GRN RED
4
914
WHT
123
321
BLK
13
83
RED
BRN MAIN CIRCUIT
VB
VA
WHT
GAUGE CONTROL MODULE (TACH)
BLK
412 SRS UNIT
ODS UNIT
7112 No. 9
(7.5 A) (7.5 A)
No. 10
No. 11
(10 A)
8
9 41
BRN
BLK
YEL
BLU GRN J
BATTERY
BAT
IG1
IGNITION SWITCH
UNDER-DASH FUSE/RELAY BOX
BLK
GRN
WHT BRN
A17
DRIVE CIRCUIT DRIVE CIRCUIT
F-CAN TRANSCEIVER
16 1 19
WHT RED
A
A6
24
ORN
LT BLU
A
11 12
17 18
UNDER-HOOD
FUSE/RELAY BOX
DATA LINK
CONNECTOR
(DLC)
JUNCTION
CONNECTOR
JUNCTION
CONNECTOR
SEAT BELT
REMINDER
INDICATOR
SIDE
AIRBAG
CUTOFF
INDICATOR
SRS
INDICATORJUNCTION
CONNECTOR
To
SRS
UNIT ODS
UNIT
HARNESS OPDS
SENSOR
JUNCTION
CONNECTOR DASHBOARD
WIRE
HARNESS
FRONT
PASSENGER’S
WEIGHT
SENSOR
(FRONT
INNER
SIDE) FRONT
PASSENGER’S
WEIGHT
SENSOR
(REAR
INNER
SIDE) FRONT
PASSENGER’S
WEIGHT
SENSOR
(FRONT
OUTER
SIDE)FRONT
PASSENGER’S
WEIGHT
SENSOR
(REAR
OUTER
SIDE)
DASHBOARD
WIRE
HARNESS
FLOOR
WIRE
HARNESS
DASHBOARD
WIRE
HARNESS
PASSENGER’S
AIRBAG CUTOFF
INDICATOR
JUNCTION
CONNECTOR
MEMORY
ERASE
SIGNAL
(MES)
CONNECTOR
(2P)
FRONT
PASSENGER’S
SEAT
WIRE
HARNESS
(With
seat heater) D 2
JUNCTION
CONNECTOR
2
C782
C783 18P CAN
HI
MES
CAN
LO
K-LINE SCS PTT
SRS
GND (2) SRS
GND (1)
8P
4P
a
08/08/21 13:55:38 61SNR030_240_0044
ProCarManuals.com
DYNOMITE -2009-

 
 
(#'   
   '

-)
µ
µ µ
µ
YES
NO Special Tools Required
YES
NO
DTC 21-1x (‘‘x’’ can be 0 thru 9 or A thru F):
24-6224-62SRS
DTC Troubleshooting (cont’d)
DASHBOARD WIRE HARNESS
4P CONNECTOR
070AZ-SNAA100
070AZ-SNAA200 07SAZ-TB4011A
A
12. Measure the resistance between each terminal of
the SRS simulator lead and body ground. There
should be an open circuit or at least 1 M .
Faulty SRS unit or poor connection at SRS
unit connector A (28P) and the SRS unit. Check the
connection between the connector and the SRS
unit. If the connection is OK, replace the SRS unit
(see page 24-203).
Short to ground in the dashboard wire
harness; replace the dashboard wire harness, then
clear the DTC.  SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
3. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
4. Remove the B-pillar lower trim (see page 20-72), then disconnect the floor wire harness 4P
connector (A) from the driver’s seat belt tensioner.
5. Connect the SRS inflator simulator (2 connectors) and simulator lead K to the floor wire
harness.
Open in the Driver’s Seat Belt Tensioner
Is the resistance as specif ied? Does the SRS indicator stay on, and is DT C 21-1x
indicated?
08/08/21 13:56:54 61SNR030_240_0062
ProCarManuals.com
DYNOMITE -2009-

µ
 
(#'   
   '
-) 
µ
µ
µ
µ µ
µ
YES
NO
YES
NO Special Tools Required
YES
NO
DTC 21-3x (‘‘x’’ can be 0 thru 9 or A thru F):
24-6324-63
SRS UNIT CONNECTOR B (28P)
6. Reconnect the negative cable to the battery.
7. Clear the DTC memory.
8. Read the DTC (see page 24-22). Go to step 9.
Open in the driver’s seat belt tensioner;
replace the driver’s seat belt (see page 24-4), then
clear the DTC.
9. Turn the ignition switch to LOCK (0). Disconnect the negative cable from the battery, then wait at least 3
minutes.
10. Disconnect both seat belt buckle tensioner connectors (see step 8 on page 24-21) and front
passenger’s seat belt tensioner connector (see step
7 on page 24-21).
11. Disconnect SRS unit connector B (28P) from the SRS unit (see step 9 on page 24-21).
12. Measure the resistance between SRS unit connector B (28P) terminals No. 1 and No. 2. There
should be 2.0 3.0 .
Faulty SRS unit or poor connection at SRS
unit connector B (28P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 24-203).
Open in the floor wire harness; replace the
floor wire harness, then clear the DTC.  SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead K 070AZ-SNAA200
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
(cont’d)
Short to Another Wire or Decreased
Resistance in the Driver’s Seat Belt Tensioner
Wire side of female terminals
I s DT C 2 1-1x i nd i cat ed ?
Is the resistance as specif ied? Does the SRS indicator stay on, and is DT C 21-3x
indicated?
08/08/21 13:56:54 61SNR030_240_0063
ProCarManuals.com
DYNOMITE -2009-