battery Acura ILX 2013 Navigation Manual

15Quick Reference Guide
Troubleshooting
For more Information
(P193)
Why does the vehicle position icon on the map “lag” a
short distance behind my actual position, especially at
intersections?
This is normal. The navigation system is unaware of the
width of intersections. Large differences in vehicle position
can indicate a temporary loss of the GPS signal.
Why does the “time to destination” display sometimes
increase even though I am getting closer to my
destination?
The “time to destination” is based on your actual road
speed and traffic conditions to give you a better estimate
of arrival time.
Why does my clock frequently change the time forward
and backward by one hour?
The clock setting is automatically updated based on your
GPS location. If you normally drive between two time
zones, the clock may keep adjusting the time. You can
turn this feature off.
2Clock Adjustment
P. 55
How do I specify a destination when an entered city or
street could not be found?
Try entering the street first. Some cities are lumped in with
a major metro area. In rural “unverified” areas or new
subdivisions, streets may be missing or only partially
numbered.
How do I turn on the navigation system voice guidance?
1.Press the INFO button. Rotate i to select Set up and
press u. Check that Volume is not set to OFF.
2.Move y to select Other, rotate i to select Basic
Settings, and press u. Set Voice Recognition Tutor
to ON if you want the system to provide confirmations
and system prompts.
My battery was disconnected or went dead, and the
navigation system is asking for a code. Where do I find it?
In most cases, you do not need to enter a code. Simply
press and hold the VOL 9 (Volume/Power) button for two
seconds; the system should reactivate.
2System Initialisation
P. 206

125
XX
Audio System
XAudio System Theft Protection
Audio
Audio System Theft ProtectionThe system is disabled when it is disconnected from the power source, such as when
the battery is disconnected or goes dead.
■Reactivating the System
1.Set the power mode to ON, and turn on the system.X
If you set the power mode to ACCESSORY, you will be requested to enter the
security code. See step 3.
2.Press and hold the VOL 9 (Volume/Power) button again for more than two
seconds.
X
The system is reactivated when the system’s control unit recognizes that the
system is in your vehicle.
X
If the control unit fails to recognize, “ENTER CODE” appears on the navigation
screen.
3.Enter the security code.
X
If you do not enter the code correctly after 10 tries, leave the system for one
hour before trying again, or visit a dealer to have the system reset.
1Audio System Theft Protection
Find the audio system’s security code and serial
number label in your Owner’s Manual kit.
Do not store the label in your vehicle. If you lose
the label, you must first retrieve the serial
number, and then obtain the code from a dealer.

164
XX
Bluetooth® HandsFreeLink®
XPairing a Phone
Bluetooth® HandsFreeLink®
Pairing a PhoneHPHONE button
When no Bluetooth-compatible phone has ever been paired to the system, the
following screen appears:
1.Rotate i to select Yes. Press u.
2.Put your cell phone in “Discovery”
or “Search” mode.
3.Press u to select OK.
X
The system begins to search for
your phone.
4.Rotate i to select your phone in
the list. Press u.
X
Select PHONE NOT FOUND? if
your phone is not found.
X
Refer to your phone manual for
instructions on searching for a
Bluetooth® device.
5.Enter the four-digit pass-key on
your phone when prompted to
complete the pairing process.
1Pairing a Phone
Your Bluetooth-compatible phone must be
paired to HFL before you can make and receive
hands-free calls.
You can control the HFL system using voice
commands.
2HFL Menus P. 178
The maximum range between your phone and
vehicle is about 30 feet (10 meters).
Phone Pairing Tips•You cannot pair your phone while the vehicle
is moving.•Your phone must be in discovery or search
mode when pairing the phone. Refer to your
phone’s manual.•Up to six phones can be paired.•Your phone’s battery may drain faster when it
is paired to HFL.•If your phone is not ready for pairing or not
found by the system within three minutes, the
system will time out and returns to idle.•The default pass-key “0000” is used until you
change the setting.
Pass-Key
You can change the pass-key setting.
2Changing the Pass-key P. 166

177
XX
Bluetooth® HandsFreeLink®
XReceiving a Call
Bluetooth® HandsFreeLink®
Receiving a Call
1.Press the h (Pick-Up) button to
answer a call and display the
Calling screen.X
“HANDSFREELINK” is also
displayed on the display.
2.Press the j (Hang-Up) button to
terminate the call.
The following options are available during a call:
•Dial Tones (available on some phones): Allows you to send numbers or names
during a call. This is useful when you call an automated phone system.
•Transfer: Allows you to transfer a call from HFL to your phone, or from your
phone to HFL.
•Mute: Allows you to mute your voice.
1Receiving a Call
An incoming call notification appears on the
screen, and you hear an audible ring tone.
If your phone has Call Waiting, press the h
button to put the original call on hold and
answer the incoming call. To return to the
original call, press the h button again. If you
want to hang up the original call and answer the
new call, press the j button.
To change the volume level of HFL, use the audio
system volume knob or the steering wheel
volume controls.
Some phones may send battery, signal strength,
and roaming status information to the screen.
Phone Book
Displays the cell phone’s imported phonebook.
2Using the Phonebook P. 175
Call IDBluetooth indicator Roaming status
Signal strength Battery level

199
XX
Troubleshooting
XMiscellaneous Questions
Troubleshooting
Miscellaneous Questions
Problem
Solution
My clock frequently changes forward and backward by
one hour.
The clock setting is automatically updated based on your GPS location. If you live and
work on the boundary between two time zones, you can turn off this feature. 2Clock Adjustment
P. 55
The clock changes even when I am not driving near a
time zone boundary.
The time zone boundaries are only approximated in the navigation system. Depending
on the geography of the time zone boundary, the switch to a different zone can be
erratic. 2Clock Adjustment
P. 55
My province does not observe daylight saving time.
How do I turn off this feature?
Press the INFO button. Select Set up > Other > Clock Adjustment, and set Auto
Daylight to OFF. 2Clock Adjustment
P. 55
Daylight saving time has started, but the navigation
system did not change time even though Auto
Daylight is set to ON.
The automatic daylight feature does not work in regions where the daylight saving
time system has not been adopted.
The navigation system automatic daylight feature is
not switching the navigation system clock on the
correct dates.
Press the INFO button. Select Set up > Other > Clock Adjustment, and set Auto
Daylight to ON. Note that the automatic daylight feature does not work in regions
where the daylight saving time system has not been adopted. 2Clock Adjustment
P. 55
The navigation system clock switched by one hour for
no apparent reason.
You may be driving near a time zone boundary. 2Clock Adjustment
P. 55
My battery was disconnected or went dead, and the
navigation system is asking for a code.
Press and hold the VOL 9 (Volume/Power) button for two seconds. The system
should reactivate. If you have installed an aftermarket system, contact a dealer.2Entering the Security Code
P. 206
How do I change the interface language?
Press the INFO button. Select Set up > Other > Language, and set the language to
English, Français, or Español.

206Reference Information
System InitialisationThe navigation system must be initialised if
power to the navigation system is
interrupted for any reason (e.g., the
battery was disconnected).Entering the Security CodeFind the navigation system’s security code
and serial number label in your Owner’s
Manual kit. Do not store the label in your
vehicle. If you lose the label, you must first
retrieve the serial number, and then obtain
the code. You can find out about your
serial number and security code from a
dealer.
1.Set the power mode to ON, and turn on
the audio system.X
If you set the power mode to
ACCESSORY, you will be requested
to enter the security code. See step 3.
2.Press and hold the VOL 9 (Volume/
Power) button for more than two
seconds.
X
The system is reactivated when the
system’s control unit recognizes that
the system is in your vehicle.
If the control unit fails to recognize,
“ENTER CODE” appears on the
navigation screen.
3.Enter the security code.
X
If you do not enter the security code
correctly after 10 tries, leave the
system for one hour before trying
again, or visit a dealer to have the
system reset.
Acquiring GPS InformationDepending on the length of time the
power was interrupted, your system may
require GPS initialisation.
If initialisation is not necessary, the system
proceeds directly to the Startup
Confirmation screen.
If the system fails to locate a sufficient
number of satellites to locate your position
within 10 minutes, the following screen is
displayed.