Valve ACURA INTEGRA 1994 Service Repair Manual

Description
Hydraulic Control (cont'dl
Ragularol Valve Body
The .egulator valve body is located on the main valve body. The regulator valve body consists of th€ regulator valva,
toroue converter check valve, cooler check valve, and lock-up contlol valve.
REGULATOR VALVE
REGULATOR VALVEBODY
COOLER CHECK VALVE
LOCT.UP CONTROI. VALVE
TONOUE COI{VERTEBCHECK VALVE
Lock-up Valvo Body
The lock-up valve body with the lock-up shilt valve and lock-up timing B valve is located on th€ regulator volvs body.
LOCK.UP SHIFT VALVE
TIMITG B VALVE
14-24

Rcgulator Valve
The r€gulator valve maintains a constant hydraulic pressure from the oil pump to the hydraulic control system, whil€
alEo furnishing oil to the lubricating system and torque convener.
Oil flows through B and B'. The oil which enters through B flows thfough the valve orifice to A, pushing the regulator
valve to the right. Acco.ding to the level of hydraulic pressure through B, the position of the valve changes, and the
amount of the oil thlough D from B'thus changes. This operation is continued. thus maintaining the line pressure.
IEI{GINE ]IIOT RUNNINGI{ENGINE RUNNING)
Siator Reaction Hydtaulic Pressure Control
Hydraulic pressure increase, according to torque, is performed by the regulator vslve using stator torque reaction. Thestator shaft is splined to the stator and its a.m end contacts the fegulator spring cap. When the car is accelerating orclimbing (Torque Convener Range). stator torque reaction acts on the stator shalt and the stator shaft arm pushes thersgulator spring cap in this - direction in proportion to the reaction. The spring compresses and the regulator valve movesto increase the regulated control pressure or line pressure. Line pressure is maximum when the stator reaction is maximum.
TOR VALVE
(cont'd)
From OIL PUMP
STATOR SHAFTSTATOR SHAFT ARM
14-25

Description
Hydraulic Control (cont'dl
Main Valvo Body
The manual valve, 1-2 shift valve, 2-3 shift valve. 4th exhaust valve. CPC valve, and relief vatve are all assembled inthe main valve body,
The primary function of this valve body is switching oil passages on and off and controlling the hydraulic pressure gotngto the hydraulic control system.
4TH EXHAUST VALVECPC VALVE
RELIEF VALVE
MANUAL VALVEMAIN VALVE BODY
S€condary Vslve Body
The secondary valve body is located on the main valve body. The 3-2 kick-down valve, 4-3 kick-down valve. 2-3 orificecontrolvalve. orifice controlvalve, 3-4 shift valve, modulator valve, and servo control valve are assembled in the secon-da.y valve body.
ORIFICE COIITROLVALVE2-3 ORIFICE CONTBOL VALVE
3.4 SHIFT VALVE
VALVE BODY
MOOULACOITTROL VALVE
1.2 SHIFT VALVE
14-26

S6rvo Body
The servo bodv is located on the secondary valve body.
The servo valve is integrated with the shiit fork shatt, throttle valve B. and accumulator pistons, which are all assembled
in the servo bodv.
SERVO VALVE/SHIFT FORK SHAFT
THROTTLE VALVE BSERVO BODY
Accumulator Pislons
The accumulator pistons are assembled in the servo body and right side cover. The l st-hold clutch accumulator piston
is in the right side cover, and the 1st, 2nd 3rd, and 4th accumulator pistons are assembled in lhe servo body.
RIGHT SIDE COVER
THROTTLE LONG VALVE
1ST-HOLD ACCUMULATOR
4TH ACCUMULATOR
IST ACCUMUI-ATOR
2ND ACCUMULATOR PISTON3RD ACCUMULATOR PISTON
14-27

Description
Genelal Chart ol Hydraulic Pressure
Hydraulic Flow
. Regulator Valve
. Manual Valve
. Modulator Valve
. 1-2 Shilt Valve l. 2-3 Shitt Valve. 3 4 Shift Vlave ]
. Throttle Valve B
Oil Pump - Regulator Valve -
Distribution ot Hydraulic Pressure
Line Pressure
Torque Converter Pressure
Lubrication Pressure
-,.Ltne rressure
] Torque Converter Pressure
L Lubrication Pressure
To Select Line Pressure
Modulator Pressure
Clutch Pressure
Throttle B Pressure
NO.DESCRIPTION OF PRESSURENO.DESCRIPTION OF PRESSURENO.DESCRIPTION OF PRESSURE
ILIN E6CMODULATOR
ITOCK-UP CONTROL SOLENOID VATVE AI55THROTTLE B
2LIN E6DMODULATOR(IOCX.UP CONTROT SOTENOID VALVE B)56THROTTLE B
3LIN E9LIN E57THROTTLE B
3'LINE10l ST CLUTCH58THROTTLE B
3"LINE1ST-HOLD CLUTCH90TOROUE CONVERTER
4LIN EIt)l ST.HOLD CLUTCH91TOROUE CONVERTER
LIN E18LINE92TOROUE CONVERTER
5LIN E202ND CLUTCH93OIL COOLER
5'LIN E212ND CLUTCH94TOROUE CONVERTER
5"LIN E25LIN E95LUBRICATION
6MODULATOR303RD CLUTCH96TOROUE CONVERTER
6'MODULATOR313RD CLUTCH97TOROUE CONVERTER
6AMODULATOR(SHIFT CONTROL SOTENOID VALVE A404TH CLUTCH99SUCTION
6BMODULATOR(SHIFT CONTROL SOLENOID VALVE B414TH CLUTCHBLEED
14-28

E Position
As the engine turns, the oil pump also starts to operate. Automatic transmission fluid (ATF) is drawn from (99) and dis-
charged into (1 ). Then, ATF pressure is controlled by the regulator valve and becomes line pressure ( 1 ). The torque con-
verter inlet pressure (92) enters (94) of torque converter through the orifice and discharges into {90}.
The torque converter check valve prevents the torque converter pressure from rising'
Under this condition, the hydraulic pressure is not applied to the clutches.
NOTE:. When used, "left" or "right" indicates direction on the llowchart
. SOL-@: Shift Control Solenoid Valve A
' SOL{D:Shift Control Solenoid Valve B
. SOL@: Lock-up Control Solenoid Valve A
. SOL-@: Lock-up Control Solenoid Valve B
(cont'd)
14-29

Description
Hydraulic Flow (cont'd)
L1l Position
The line pressure {1) becomes line pressure (4) at the manual valve and passes to the lst clutch and 1st accumulator.Then line pressure (41 flows through the 1st-hold clutch and lst-hold accumulator.
Fluid flows by way of:- Line Pressure {4} - 1-2 Shitt Valve * 2-3 Shitt Valve - 3rd Clutch Pressure {31) - 3-4 Shift Valve - 4th ClutchPressure (41) - Manual Valve - lst-hold Clutch Pressure {15) - 1st-hold Clutch
The modulator pressure (6) is supplied to the 1-2 and 2-3 shift valves.The line pressure (1) also flows to throttle valve B.
NOTE:. When used. "left" or "right" indicates direction on the flowchart.. SOL-@: Shift Control Solenoid Valve A. SOL@: Shift Control Solenoid Valve B. SOL-@: Lock-up Control Solenoid Valve A. SOL-@: Lock-up Control Solenoid Valve B
14-30

f4 Position
ihe line pressure (11 becomes line pressure (41 as it passes through the manual valve.lt then goes through line l2O)
to the 2nd clutch via the 1-2 and 2-3 shift valves. Also, line pressure (1 ) goes to the modulator valve through the filter
and becomes the modulator pressure (6). Modulator pressure (6) is not supplied to the 1-2, 2-3 and 3-4 shift valves
because the shitt control solenoid valves A and B are turned on by the TCM.
NOTE:. When used, "left" or "right" indicates direction on the flowchart
. SOL-@: Shift Control Solenoid Valve A
. SOL-@: Shilt Control Solenoid Valve B
. SOL-O: Lock-up Control Solenoid Valve A
. SOt -@ : Lock-up Control Solenoid Valve B
(cont'd)
14-31

Description
Hydraulic Flow (cont'dl
@ or @ Position
1. lst Spe€d
The flow of fluid throuth the torque convener circuit is the same as in S Oosition.The line pressure ( 1 ) becomes line pressure (4) and it becomes the 1 st clutch pressure (1O). The I st ctutch pressure
is applied to the lst clutch and l st accumulator; consequently, the vehicle will move as the engine power is transmitted.The line pressure (1) becomes the modulator pressure (6) by the modulator valve and travels to 1-2 and 3-4 shift valves.
The 1-2 shift valve is moved to the right side because the shilt control solenoid valve A is turned off and B is turned
on by the TCM. This valve stops 2nd clutch pressure and power is not transmitted to the 2nd clutcn.Line pressu.e {4) also tlows to the seryo valve and line pressure (1 } also flows to throttle valve B.
NOTE:. When used, "left" or "right" indicates direction on the flowchart.. SOL-@: Shitt Control Solenoid Valve A. SOL-@:Shift Control Solenoid Valve B. SOL-O: Lock-up Control Solenoid Valve A. SOL-@: Lock-up Control Solenoid Valve B
14-32
I

2nd Sgeed
The llow of fluid up the 1-2 shift valve is the same as in 1st speed. As the speed of the car reaches the prescribed
value, the solenoid valve A is tulned on by means ot the TCM. As a result, the 1-2 shift valve is moved to the left
and uncovers the port leading to the 2nd clutch; the 2nd clutch is engaged'
Fluid flows by way of:- Line Dressure l4l - 'l-2 Shift Valve - 2-3 Shitt Valve - 2nd Clutch Pressure (2'1) * 2nd Clutch
The hvdraulic pressure also flows to the 1st clutch, However, no power is transmitted because of the one-way clutch.
NOTE:. When used, "lett" or "right" indicates direction on the flowchart
. SOL-@: Shift Control Solenoid Valve A
. SOL@: Shift Control Solenoid Valve B
. SOL-@: Lock-up Control Solenoid Valve A
. SOL-@: Lock-up Control Solenoid Valve B
{cont'd)
14-33