ACURA INTEGRA 1998 Service Repair Manual

ACURA INTEGRA 1998 Service Repair Manual INTEGRA 1998 ACURA ACURA https://www.carmanualsonline.info/img/32/56983/w960_56983-0.png ACURA INTEGRA 1998 Service Repair Manual
Trending: belt, ecm, change wheel, c301, frame, coolant neck, display

Page 571 of 1680

ACURA INTEGRA 1998  Service Repair Manual Countershaft Bearing Replacement
\J
J\
\
1. Remove the countershaft bearing using the special
lools as shown.
3/8" 16 SLIDE HAMMER(Commercially available)
ADJUSTAELEBEARINGPULLER,25-40 mm07736 AO1000A

Page 572 of 1680

ACURA INTEGRA 1998  Service Repair Manual Transmission Housing Bearings
Mainshaft/Countershaft Bearing Replacement
1, To remove the mainshaft and countershaft bearings
from the transmission housing, expand each snap
ring with snap ring pliers

Page 573 of 1680

ACURA INTEGRA 1998  Service Repair Manual JI
JI
)
1.To remove the sub-shatt bearing from the transmis-
sion housing, expand the snap ring with snap ringplie.s, then push the bearing out using the special
tools and a Dress as shown.
NOTE: Do n

Page 574 of 1680

ACURA INTEGRA 1998  Service Repair Manual Reverse ldler Gear
Installation
Fn" 
14-158
\
\
Parking Brake Stop
I nspection/Adjustment
1.
2.
Set the parking brake lever in the E position.
N4easure the distance between the parking brake
pawl shaf

Page 575 of 1680

ACURA INTEGRA 1998  Service Repair Manual Transmission
NOTE:
a Coat all parts with ATF.
a Replace the parts below:. O-rings. Lock washers. Gaskets. Locknuts. Conical spring washers. Sealing washers
TOROUE: 6 x 1.0 mm Bolt 12 Nm (1.2 kgf.m, 8

Page 576 of 1680

ACURA INTEGRA 1998  Service Repair Manual )
)
A
1.
ATF PUMP DRIVENGEAR SHAFT
ATF PUMPDRIV€N GEAR
J.
6
Grooved and ch6mleredside faces separatorplate.
Install the suction pipe collar in the torque conven-
er housing.
Install the main separat

Page 577 of 1680

ACURA INTEGRA 1998  Service Repair Manual Transmission
TRANSMISSIONMOUNT BRACKET
Reassembly (contd)
TRANSMISSIONHANGER
Efr
E
12 x 1.25 mm49 N.m (5.O
36 tbf.fr)
CONNECTOR BRACKET
NEEDLE BEARII{G
REVERSE GEAR
MAINSHAFT
SHIFT FORK
REVERSE SELEC

Page 578 of 1680

ACURA INTEGRA 1998  Service Repair Manual 18. Install the sub-shaft assembly in the transmission
housing {see page 14-142],.
19. Install the reverse idler gear and gear shaft holder(see page 14-158).
20. Install the differential assembly in

Page 579 of 1680

ACURA INTEGRA 1998  Service Repair Manual Transmission
SUB.SHAFT
MAINSHAFT
Reassembly {contd)
27. lnstallthe specialtool onto the mainshaft as shown.
Install the parking brake lever on the control shaft.
Assemble the one-way clutch and the p

Page 580 of 1680

ACURA INTEGRA 1998  Service Repair Manual )37.
38.
Align the hole of the sub-shaft 1st gear with the
hole of the transmission housing. then insert a pin
to hold the sub-shaft while tightening the sub-shaft
locknut.
Install a new conical sprin
Trending: brake fluid, air conditioner, 23-169, turn signal bulb, spare tire location, oil, wheelbase