light Acura Integra 2000 Hatchback Repair Manual

Light
s

Replacin g a Headligh t Bul b
Your car has two bulbs on each side, four in total. Make sure you arereplacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handle
it by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
1. Open the hood.
If you need to change the high
beam headlight bulb on the
passenger's side, remove the
radiator reserve tank by pulling it straight up.

2. To disconnect the bulb from the

electrical harness, push on the end
of the lock tab to release the
connector then push the connec-
tor straight down.

3. Turn the bulb about one-eighth

turn counterclockwise to unlock it
from the headlight assembly.

4. Remove the bulb by pulling it

straight out of its recess.

5. Align the tabs on the new bulb
with the slots in the headlightassembly and push it into place.
6. Turn the bulb clockwise to lock it

in place. Do not force it. Check the seating of the bulb's tabs in the
slots if the bulb will not return to
its original position.

7. Reinstall the harness connector on

the bulb connector. Make sure it
locks in place.
Turn on the headlights to test the new bulb.

8. (Passenger's side)

Reinstall the radiator reserve tank.

Maintenanc e

NOTIC
E

Light
s
Replacing Front Turn Signal/
Parkin g an d Sid e Marke r Ligh t
Bulb s
1. Use a Phillips-head screwdriver to

loosen the light assembly's mounting screw.

2. Remove the light assembly from

the bumper.

3. Remove the socket of the burned-

out bulb from the light assembly
by turning it one-quarter turn counterclockwise.

4. To remove the front bulb, push it

in slightly and turn it counterclock-
wise. To remove the side bulb, pull it straight out of its socket.

5. Install the new bulb in the socket.
6. Insert the socket back into the

light assembly. Turn it clockwise
to lock it in place.

7. Test the lights to make sure the

new bulb is working.

8. Put the light assembly into the

bumper. Make sure the tab on the
light assembly fits into the bumper slot. Tighten the mounting screw.

Maintenanc e
SCRE
W

Light
s

Replacin g a High-moun t Brak e
Ligh t Bul b
LS model
1. Undo the cover fasteners by
pushing on the center of each
fastener's head until it pops in.
Remove the cover.

2. Determine which bulb is burned

out.

3. Pull the bulb straight out of its

socket.
Push the new bulb straight into
the socket until it bottoms.

4. Test the lights to make sure the

new bulb is working.

5. Reset each fastener by pushing on

the pointed end until it pops back almost flush with the fingers on
the housing.

6. Reinstall the cover. Secure each

fastener by pushing on the center
until it locks (the center is flush
with the head).

Maintenanc e

Light
s

Replacin g Rea r Tur n Signa l an d
Sid e Marke r Ligh t Bulb s
1. Open the hatch and remove the
light assembly cover by pulling the
edge.

2. Remove the socket from the light assembly by turning it one-quarter

turn counterclockwise.

3. If the turn signal light bulb is

burned out, remove it by pushing
it in and turning counterclockwise.If the side marker light bulb is
burned out, remove it by pulling it straight out of its socket.

4. Install the new bulb in the reverse

order of removal.

5. Push the socket into the light

assembly and turn it clockwise
until it locks.

6. Test the lights to make sure the

new bulb is working.

7. Install the light assembly cover.

Make sure it locks in place.

Replacin g Tail/Stopligh t an d
Back-u p Ligh t Bulb s
1. Open the hatch. Remove the

tether hardware cover with a small
flat-tip screwdriver and tether
anchor plate with a wrench by turning the bolt counterclockwise.

When reinstalling tether hardware,

see Protecting Children on page

41.

On Type-R model

You cannot replace these bulbs
yourself, contact your Acura dealer.
Maintenanc e

Light
s

2. Undo the seven cover fasteners by
pushing on the center of each
fastener's head until it pops in. Remove the taillight cover panel.

3. Remove the socket by turning it
one-quarter turn counterclockwise. 4

. Try the tail/stoplights and back-up
light to verify which bulb needsreplacing. Remove the bulb by
turning it counterclockwise.

5. Install the new bulb in the socket.

Test it to make sure it works.

6. Reinstall the socket into the light

assembly.

7. Reinstall the tether anchor

hardware. Make sure the toothed washer ison the bottom of the bolt. Tighten
the bolt to:
16 lbf.ft (22 N.m , 2.2 kgf.m)
If a torque wrench was not used,
see your Acura dealer as soon as
possible to verify proper
installation.

CONTINUED

Maintenanc e

Light
s
8. Reset each fastener by pushing onthe pointed end until it pops back almost flush with the fingers on
the housing.
9. Reinstall the cover. Secure each
fastener by pushing on the center
until it locks (the center is flush with the head).
Replacin g a Rea r Licens e Bul b
1. Remove the two screws and
remove the license light assembly.
2. Remove the socket from the light assembly by turning it one-quarter
turn counterclockwise.
3. Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.
4. Turn on the parking lights and
check that the new bulb is
working.
5. Reinstall the license light assem-
bly. Install the two screws and
tighten them securely.
Maintenanc e

Light
s

Replacin g Ceiling , Spo t an d Carg o
Are a Ligh t Bulb s
The ceiling, spot and cargo area lights come apart the same way.
They do not all use the same bulb.
1. Remove the lens by carefully
prying on the edge of the lens with
a fingernail file or a small flat-tip
screwdriver. Do not pry on the
edge of the housing around the
lens.

2. Remove the bulb by pulling it

straight out of its metal tabs.

3. Push the new bulb into the metal

tabs. Snap the lens back in place.
LS, GS and GS-R models

Maintenance

SPOTLIGHT
S
CEILIN G LIGH T CARG
O ARE A LIGH T

Storin
g You r Ca r
If you need to park your car for an
extended period (more than one
month), there are several things you should do to prepare it for storage.
Proper preparation helps prevent deterioration and makes it easier to
get your car back on the road. If
possible, store your car indoors.
Fill the fuel tank.Change the engine oil and filter (see page 173). Wash and dry the exterior

completely.
Clean the interior. Make sure the
carpeting, floor mats, etc. are
completely dry.
Leave the parking brake off. Put
the transmission in Reverse (5- speed manual) or Park (automatic). Block the rear wheels.
If the car is to be stored for a
longer period, it should be supported on jackstands so the
tires are off the ground. Leave one window open slightly (if
the car is being stored indoors). Disconnect the battery.
Support the front and rear wiper
blade arms with a folded towel or rag so they do not touch the

windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and hatch seals. Also, apply a body
wax to the painted surfaces that mate with the door and hatch seals. Cover the car with a "breathable"
cover, one made from a porous
material such as cotton.
Nonporous materials, such as
plastic sheeting, trap moisture,
which can damage the paint. If possible, run the engine for a
while periodically (preferably once a month).
If you store your car for 12 months or longer, have your Acura dealer
perform the inspections called for in
the 24 months/30,000 miles (48,000
km) maintenance schedule (Normal Conditions) as soon as you take it
out of storage (see page 162 ). The
replacements called for in the
maintenance schedule are not needed unless the car has actually
reached that time or mileage.
Maintenanc e

Exterio
r Car e
Washin g
Frequent washing helps preserve
your car's beauty. Dirt and grit can scratch the paint, while tree sap and
bird droppings can permanently ruin
the finish.
Wash your car in a shady area, not in direct sunlight. If the car is parked in
the sun, move it into the shade and
let the exterior cool down before you
start.

Only use the solvents and cleaners
recommended in this Owner's Manual.

Chemical solvents and strong cleaners
can damage the paint, metal, and
plastic on your car.
Rinse the car thoroughly with cool
water to remove loose dirt. Fill a bucket with cool water. Mix
in a mild detergent, such as
dishwashing liquid or a product
made especially for car washing.
Wash the car using the water and detergent solution and a soft-
bristle brush, sponge, or soft cloth. Start at the top and work your waydown. Rinse frequently.
Check the body for road tar, tree
sap, etc. Remove these stains with
tar remover or turpentine. Rinse it off immediately so it does not
harm the finish. Remember to re-
wax these areas, even if the rest of the car does not need waxing. When you have washed and rinsed
the whole exterior, dry it with achamois or soft towel. Letting itair-dry will cause dulling and water

spots.
As you dry the car, inspect it for
chips and scratches that could allow
corrosion to start. Repair them with
touch-up paint (see page 217).
Powe r Antenn a Cleanin g
Twice a year, clean the antenna mast with a dry cloth and mild detergent. Scrub the antenna in upward strokes
to avoid bending it. Rinse with water.
Make sure the antenna works
smoothly by turning the stereo off
and on several times with the
ignition switch ON (II). The antenna does not need lubricating.
If you use a "drive-through" car wash,
make sure you turn the stereo off
first. This retracts the antenna to prevent damage from the car wash
brushes.

Appearanc e Car e

NOTIC
E

Exterio
r Car e

Waxin g
Always wash and dry the whole car before waxing it. You should wax
your car, including the metal trim, whenever water sits on the surface in large patches. It should form into
beads or droplets after waxing.
You should use a quality liquid or paste wax. Apply it according to theinstructions on the container. In
general, there are two types of
products:
Waxes — A wax coats the finish and protects it from damage by exposure
to sunlight, air pollution, etc. Youshould use a wax on your Acura
when it is new.
Polishes — Polishes and cleaner/
waxes can restore the shine to paint
that has oxidized and lost some of its shine. They normally contain mild
abrasives and solvents that remove
the top layer of the finish. You should use a polish on your Acura if
the finish does not have its original shine after using a wax.
Cleaning tar, insects, etc. with
removers also takes off the wax.
Remember to re-wax those areas, even if the rest of the car does not

need waxing.

Aluminu m Wheel sOn some models
Clean your Acura's aluminum alloy
wheels as you do the rest of the exterior. Wash them with the same
solution, and rinse them thoroughly.
The wheels have a protective clear- coat that keeps the aluminum from
corroding and tarnishing. Using
harsh chemicals, including some commercial wheel cleaners, or stiff
brushes can damage this clear-coat. Only use a mild detergent and soft
brush or sponge to clean the wheels. Pain
t Touch-u p
Your dealer has touch-up paint to match your car's color. The color
code is printed on a sticker on the driver's doorjamb. Take this code to
your dealer so you are sure to get the correct color.
Inspect your car frequently for chips
or scratches in the paint. Repair
them right away to prevent corrosion of the metal underneath. Use the
touch-up paint only on small chips and scratches. More extensive paint
damage should be repaired by a
professional.

Appearance Car e