bulb Acura Integra 2000 Sedan Owner's Manual

Indicato
r Light s
Tur n Signa l an d
Hazar d Warnin g
Indicator s
The left or right turn signal light blinks when you signal a lane change
or turn. If the light does not blink or
blinks rapidly, it usually means one of the turn signal bulbs is burned out
(see page 203). Replace the bulb as
soon as possible, since other drivers
cannot see that you are signalling.
When you turn on the Hazard
Warning switch, both turn signal
lights blink. All turn signals on the
outside of the car should flash. Hig
h Bea m Indicato r
This light comes on with the high
beam headlights. See page 61 for
information on the headlight

controls.
Cruis
e Contro l Indicato r
This lights when you set the cruise
control. See page 66 for information
on operating the cruise control.
Instrument s an d Control s
CRUIS
E

CONTRO L

This section explains why it is important to keep your car well
maintained and to follow basic
maintenance safety precautions.
This section also includes Maintenance Schedules for normaldriving and severe driving conditions,
a Maintenance Record, and instruc-
tions for simple maintenance tasks
you may want to take care of

yourself.

If you have the skills and tools to per-
form more complex maintenance tasks on your Acura, you may want
to purchase the Service Manual. Seepage 259 for information on how to
obtain a copy, or see your Acura
dealer.
Maintenance Safety....................... 154
Important Safety Precautions.. 155
Maintenance Schedule.................. 156
Maintenance Record..................... 163
Owner Maintenance Checks........ 165
Fluid Locations............................... 166

Engine Oil......................................
. 167
Adding Oil................................... 167
Recommended Oil..................... 167

Synthetic Oil............................... 169

Additives..................................... 169
Changing the Oil and Filter...... 170
Cooling System.............................. 172 Adding Engine Coolant............. 172Replacing Engine Coolant........ 174
Windshield Washers..................... 177
Transmission Fluid........................ 178 AutomaticTransmission.......................... 178

5-speed Manual
Transmission.......................... 179
Brake and Clutch Fluid................. 179 Brake System............................. 180Clutch System............................
181
Power Steering..............................
. 181
Air Cleaner Element....................... 182 Hood Latch..................................... 183
Spark Plugs..................................... 183 Replacement............................... 183
Specifications............................. 185
Battery............................................ 186
Wiper Blades.................................. 188
Air Conditioning System............... 190
Drive Belts...................................... 191
Timing Belt..................................... 191
Tires................................................ 192 Inflation....................................... 192
Inspection...................................
194
Maintenance............................... 194
Tire Rotation.............................. 195 Replacing Tires and Wheels.... 195
Wheels and Tires....................... 196 Winter Driving........................... 196

Snow Tires.............................. 197

Tire Chains............................. 197
Lights.............................................. 198
Headlight Aiming.....................
. 200
Replacing Bulbs......................... 202
Storing Your Car............................ 210

Maintenance

Light
s
Check the operation of your car's
exterior lights at least once a month.
A burned out bulb can create an unsafe condition by reducing yourcar's visibility and the ability tosignal your intentions to other

drivers.

Maintenanc e
HEADLIGHT
S
FRONT PARKING /
FRON T TUR N SIGNA L
LIGH T FRON
T SID E
MARKE R LIGH T

Light
s

Check the following: Headlights (low and high beam) Parking lights
Taillights Brake lights
High-mount brake light
Turn signals
Back-up lights Hazard light function
License plate light
Side marker lights
If you find any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on page 247 to determine what type of replacement
bulb is needed.

Maintenance

TAILLIGH
T
INNE R TAILLIGH T
LICENS E PLAT E LIGHT S

Light
s
Replacin g a Headligh t Bul b
Your car has two bulbs on each side, four in total. Make sure you arereplacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handleit by its plastic case and protect the
glass from contact "with your skin or hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.

Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
1. Open the hood.
If you need to change the high
beam headlight bulb on the
passenger's side, remove the
radiator reserve tank by pulling itstraight up.
2. To disconnect the bulb from the electrical harness, push on the end
of the lock tab to release the
connector then push the connec-
tor straight down. 3. Turn the bulb about one-eighth
turn counterclockwise to unlock it
from the headlight assembly.
4. Remove the bulb by pulling it straight out of its recess.
5. Align the tabs on the new bulb with the slots in the headlightassembly and push it into place.
6. Turn the bulb clockwise to lock it in place. Do not force it. Check theseating of the bulb's tabs in the
slots if the bulb will not return to
its original position.
7. Reinstall the harness connector on the bulb connector. Make sure it
locks in place.
Turn on the headlights to test the new bulb.
8. (Passenger's side) Reinstall the radiator reserve tank.

Maintenanc e

NOTIC
E

Light
s

Replacin g Fron t Tur n Signal /
Parkin g an d Sid e Marke r Ligh t
Bulb s
1. Use a Phillips-head screwdriver to loosen the fight assembly's
mounting screw.
2. Remove the light assembly from the bumper. 3. Remove the socket of the burned-
out bulb from the light assembly
by turning it one-quarter turn
counterclockwise.
4. To remove the front bulb, push it in slightly and turn it counterclock-
wise. To remove the side bulb, pull
it straight out of its socket. 5. Install the new bulb in the socket.
6. Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
7. Test the lights to make sure the new bulb is working.
8. Put the light assembly into the bumper. Make sure the tab on the
light assembly fits into the bumperslot. Tighten the mounting screw.
Maintenance

SCRE
W

Light
s

Replacin g a High-moun t Brak e
Ligh t Bul b
1. Open the trunk and remove the socket from the light assembly by
turning it one-quarter turn counter-
clockwise.

2. Remove the burned-out bulb by pulling it straight out of the socket.
3. Install the new bulb and reinstall the socket. Make sure the new
bulb is working. Replacin
g Rea r Bulb s
(i n Fenders )
1. Open the trunk.
2. Undo the six fasteners (two "A" type and four "B" type) and
remove the trunk wall cover. Referto pages 205 and 206 for removal
of the fasteners.
3. Remove a "B" type fastener from
the wall lining and pull off the

lining.
Maintenanc e B
Typ e
A
Typ e

Light
s
4. Remove the socket by turning it one-quarter turn counterclockwise.
5. If the turn signal light bulb or tail/stoplight bulb is burned out,remove it by pushing it in and
turning counterclockwise. If the side marker light bulb is burned
out, remove it by pulling it straight
out of its socket. 6. Install the new bulb in the reverse
order of removal.
7. Push the socket into the light assembly and turn it clockwise
until it locks.
8. Test the lights to make sure the new bulb is working.
9. Install the wall lining and the trunk wall cover and secure them with
the fasteners. Refer to page206 for reinstallation of the
fasteners. Removal and Reinstallation of
Fasteners
(A Type)

Removal:

Turn the center of the fastener one- quarter turn counterclockwise using
a coin or a screwdriver. The center
will come out slightly. Then remove the fastener.

CONTINUED

Maintenanc e

Light
s

Replacin g Rea r Bulb s (i n Trun k

Lid )
1. Open the trunk.
2. Use a Phillips-head screwdriver to remove the two screws from the
bulb holder. Remove the holder
from the taillight assembly. 3. Try the tail/stoplight and back-up
lights to verify which bulb needs
replacing. Remove that bulb from
the socket by pushing it in slightly and turning it counterclockwise.
4. Install the new bulb in the socket. Test it to make sure it works.
5. Reinstall the bulb holder assembly. Install the two screws and tighten
them securely. Replacin
g a Rea r Licens e Bul b
1. Remove the two screws and remove the license light assembly.
2. Remove the socket from the light assembly by turning it one-quarterturn counterclockwise.
3. Pull the bulb straight out of its socket. Push the new bulb in until
it bottoms in the socket.

Maintenance

CONTINUED

Light
s
4. Turn on the parking lights and check that the new bulb is
working.
5. Reinstall the license light assem- bly. Install the two screws andtighten them securely. Replacin
g Ceilin g an d Spotligh t
Bulb s
1. Remove the lens by carefully prying on the edge of the lens with
a fingernail file or a small flat-tip
screwdriver. Do not pry on the
edge of the housing around the
lens.
2. Remove the bulb by pulling it
straight out of its metal tabs.
3. Push the new bulb into the metal tabs. Snap the lens back in place.
Maintenanc e SPOTLIGH
T
CEILIN G LIGH T