clock reset Acura MDX 2002 Owner's Manual

µ
µ
µ
µ
ÓÓ
µ´
The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. The system will scan
up the band for a station with a
strong signal. When it f inds one, it
will stop and play that station f or
approximately f ive seconds. If you do
nothing, the system will then scan
f or the next strong station and play
that f or f ive seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again. To store a f requency:
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each Preset
button.
Use the TUNE or SEEK f unction
to tune the radio to a desired
station.
Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
You can use any of f our methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN or the
Preset buttons.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob clockwise to tune to a
higher f requency, or
counterclockwise to tune to a lower
f requency.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
either SEEK button ( or ), then
release it. Depending on which
SEEK button you press, the system
scans upward or downward f rom the
current f requency. It stops when it
finds a station with a strong signal. 1.
2.
3.
4.
SCAN
TUNE
Preset
SEEK
Audio System
Comf ort and Convenience Feat ures153
01/09/07 12:19:32 31S3V610_158

µµ
You can also quickly set the time to
the nearest hour. Press the CLOCK
button, then press the RESET button.
If the displayed time is before the
half hour, it will reset back to the
previous hour. If the displayed time
is af ter the half hour, it will reset
f orward to the next hour.
For example:
1:06 will reset to 1:00
1:52 will reset to 2:00
The compass shows your direction
of travel. It indicates eight directions.
Compass operation can be af f ected
by driving near power lines or
stations, across bridges, through
tunnels, over railroad crossings, past
large vehicles, or driving near large
objects that can cause a magnetic
disturbance.
It can also be af f ected by accessories
such as antennas and roof racks that
are mounted by magnets.The compass may need to be
manually calibrated af ter exposure to
a strong magnetic field. If the
compassseemstobecontinually
showing the wrong direction and is
not self -calibrating, do the f ollowing.
NOTE: You should do this procedure
in an open area, away from buildings,
power lines, and other vehicles.
The compass is self -calibrating. If
you see ‘‘ ’’ in the direction
display and ‘‘Calibrate’’ is blinking,
the compass is self -calibrating.
CONT INUED
Trip Computer
Compass Operation
Compass Calibration
Comf ort and Convenience Feat ures179
01/09/07 12:23:38 31S3V610_184

µµ
Drivethevehicleslowlyintwo
complete circles. In most areas, there is a variation
between magnetic north and true
north. Zone selection is required so
the compass can compensate f or this
variation. To check and select the
zone set into the compass, do the
f ollowing.
Press and hold the CLOCK and
TRIP buttons until the display
changes (about 1 second).
When the display goes f rom
‘‘ ’’ to an actual heading, the
unit is calibrated.
Press the CLOCK, TRIP, or
RESET button to complete the
calibration and return the display
to normal. 1.
CONT INUED
Trip Computer
Comf ort and Convenience Feat ures
Compass Zone Select ion
181
01/09/07 12:23:56 31S3V610_186

If the zone is incorrect, press and
hold the MODE button to get the
number to count down, or the A/C
button to get the number to count
up. If the zone is correct, continue
to step 5.
Press the Set (FAN) button to set
the zone selection.
Press the CLOCK, TRIP or
RESET button to exit the zone
selection and return display to
normal.
Press the Zone (A/C) button. The
zone the compass is currently set
to is displayed.
Find the zone f or your area on the
map.
2.
3. 4.
5.
6.
Trip Computer
Comf ort and Convenience Feat ures182
01/09/07 12:24:05 31S3V610_187

The Trip Computer displays the
f ollowing inf ormation. To switch to
this display, press the A/C-Trip
button.TheAvgdisplayshowsyouthe
average f uel economy since you
last reset the display. Clock
Outside Temperature.
Instantaneous f uel mileage.
The Range, or estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you have gotten over the
last several miles, so it will vary
with changes in speed, traf f ic, etc.
CONT INUED
(With Navigation System)
Trip Computer
Comf ort and Convenience Feat ures185
I INNS STTA
A N
NT TA
A N
NE EO
OU USS F
FUUE EL
L M
M I
ILLE E A
A G
GE E
J
JO OY Y S
STTI
ICCK K E
E
L
LAA P
PS
SE ED
D
T
T I
IMM E
E
R
RE ES
SE ET
T
I
IC CO ON N
T
T
R
RI IPP
M
M E
ET
TE
ER
R
O
On n/
/O
Of ff
f
I
IC CO ON N
C
CL LOOC CKK
T
T
R
RI IPP H
HI
ISST TO
OR RYY I
ICCO ON N
R
RA A N
NG GEE
A
A V
VE
ER
RA A G
GE E F
FUUE EL
L
E
E C
CO ON NOOMM Y
Y
A
A /
/C
C- -T
T R
RI IPP
B
BU UT TT
TO
ON N
C
CA A N
NC CEEL
L
B
BU UT TT
TO
ON N
S
SEET
TU
UP P I
ICCO ON N
O
OU UTTS
SI IDD E
E T
TE
EM
M P
PE
ER
RA A T
TU
UR REE
01/09/07 12:24:28 31S3V610_190