check engine light Acura MDX 2003 Owner's Manua

If the light comes on at any other
time, or does not come on at all, you
should have the system checked by
your dealer. For example:If the SRS indicator light does not
come on after you turn the ignition
switch to ON (II).
If the light stays on after the
engine starts.
If the light comes on or f lashes on
andoff whileyoudrive.
The SRS indicator light
alerts you to a potential
problem with your f ront airbags and
automatic seat belt tensioners.
This light will also alert you to a
potential problem with your side
airbags, passenger’s side airbag
automatic cutoff system (see page ), or the driver’s seat position
sensor and the f ront passenger’s
weight sensors (see pages and ).
When you turn the ignition ON (II),
this indicator will light brief ly then
go out. This tells you that the system
is working properly. If you see any of these indications,
your f ront or side airbags may not
deploy, your passenger’s side airbag
automatic cutoff system may not
work properly, your seat belt
tensioners may not work, or the
sensors under the f ront seats may
not work properly when you need
them. See your Acura dealer as soon
as possible.
57
57
58
How the SRS Indicator L ight
Works
Additional Inf ormation About Your Airbags
Driver and Passenger Saf ety56
Ignoring the SRS indicator light
can result in serious injury or
death if the airbags, cutoff
system, or tensioners do not
work properly.
Have your vehicle checked by a
dealer as soon as possible if
the SRS light alerts you to a
potential problem.

This indicator comes on f or a f ew
seconds when you turn the ignition
switch ON (II). It will then go of f if
you have inserted a properly-coded
ignition key. If it is not a properly-
coded key, the indicator will blink
and the engine will not start (see
page ).
This indicator also blinks several
times when you turn the ignition
switch f rom ON (II) to ACCESSORY
(I) or LOCK (0).
This light normally comes on f or a
f ew seconds when you turn the
ignition switch ON (II), and when
the ignition switch is turned to
START (III). If this light comes on at
any other time, there is a problem in
theABS.If thishappens,takethe
vehicle to your dealer to have it
checked. With the light on, your
vehicle still has normal braking
ability but no anti-lock. For complete
inf ormation, see page .
This light has two f unctions:
This indicator comes on when you
turn the ignition switch ON (II). It
is a reminder to check the parking
brake. A beeper sounds if you try
to drive with the parking brake not
f ully released. Driving with the
parking brake not f ully released
can damage the brakes and tires.
If the indicator remains lit after
you have f ully released the
parking brake while the engine is
running, or if it comes on while
driving, it can indicate a problem
in the brake system. For complete
inf ormation, see page .
1.
2.
91
377 264
Indicator L ights
Inst rument s and Cont rols
Immobilizer System
Indicator
Anti-lock Brake System
(A BS) Indicator
Parking Brake and Brake System
Indicator
69
U.S. Canada
Canada
U.S.

This light normally comes on f or a
f ew seconds when you turn the
ignition switch ON (II). If this light
comes on at any other time, there is
a problem in the 4WD system. Take
the vehicle to your dealer to have it
checked.
This indicator monitors the
temperature of the automatic
transmission f luid. The indicator
should come on f or a f ew seconds
when you turn the ignition switch
ON (II). If it comes on while driving,
it indicates the transmission f luid
temperature is too high. Pull to the
side of the road when it is saf e, shif t
to Park, and let the engine idle until
the indicator goes out.
If the indicator blinks while driving,
pull to the side of the road when it is
saf e, shif t to Park, and let the engine
idle until the indicator goes out.
This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. This indicator
will come on when the light switch is
in AUTO and the lights turn on
automatically. If you turn the ignition
switch to ACCESSORY (I) or LOCK
(0) without turning of f the light
switch, this indicator will remain on.
A reminder chime will also sound
when you open the driver’s door.On cars with automatic lighting (see
page ) 80
Indicator L ights
Inst rument s and Cont rols
VTM-4 Indicator
A/T Temperature
Indicator
Lights On Indicator
(U.S. models only)
72
Continuing to drive with the A/T
Temperature indicator lit may cause
serious damage to the transmission. Continuing to drive with the VTM-4
indicator blinking may cause serious
damage to the system.

This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between these
displays by pressing the Select
button repeatedly. Each trip meter
works independently, so you can
keep track of two dif f erent distances.
When you turn the ignition switch
ON (II), what you last selected isdisplayed.
To reset a trip meter, display it, and
then press and hold the Reset button
until the number resets to ‘‘0.0’’.
Both trip meters will reset if the
vehicle’s battery goes dead or is
disconnected.
This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom blue mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to the
upper white mark. If it reaches the
red (Hot) mark, pull saf ely to the
side of the road. Turn to page f or
instructions and precautions on
checking the engine’s cooling
system.
This shows how much f uel you have.
It is most accurate when the vehicle
is on level ground. It may show
slightly more or less than the actual
amount when you are driving on
curvy or hilly roads.
The needle returns to the bottom
after you turn off the ignition. The
gauge shows the f uel level reading
immediately af ter you turn the
ignition switch back ON (II).
371
Trip Meter
Temperature GaugeFuel Gauge
Gauges
Inst rument s and Cont rols75
SELECT BUTTON
RESET BUTTON
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.

The power window system has a key-
of f delay f unction. The windows will
stilloperateforuptotenminutes
after you turn off the ignition.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch ON (II) again
bef ore you can operate the windows.
If the driver’s window runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it. If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction will be disabled. The
power window system needs to be
reset af ter reconnecting the battery
or installing the f use. You should do
the f ollowing.
Any impact due to road conditions
may cause the auto reverse f unction
work unexpectedly on the closing
window. If it happens f requently,
there is a problem with your power
window system. You should have
your car inspected by your dealer.
You can still close the window by
pulling back on the window switch
lightly and hold it. If the power windows do not operate
properly af ter resetting, have your
vehicle checked by a Acura dealer.Start the engine. Push down on
the driver’s window switch until
the window is f ully open.
Pull back on the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more.
1.
2.
Power Windows
Inst rument s and Cont rols
Auto Reverse
113

Youshoulddothefollowingchecks
and adjustments every day bef ore
you drive your vehicle.Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove f rost, snow,
or ice. Check the adjustment of the seat
(see page ).
Check the adjustment of the
inside and outside mirrors (see
page ).
Check the adjustment of the
steering wheel (see page ).
Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).Turn the ignition switch ON (II).
Check the indicator lights in the
instrument panel.
Start the engine (see page ).
Check the gauges and indicator
lights in the instrument panel (see
page ).
Check that any items you may be
carrying with you inside are stored
properly or f astened down
securely. Visually check the tires. If a tire
looks low, use a gauge to check its
pressure. Check that the hood and tailgate
arefullyclosed. Makesurethedoorsandtailgate
are securely closed and locked.
3. 2.
1.
4. 5.
6.
7.
8.
9. 11.
12. 10.
15
115
89 252
67
101
Preparing to Drive
Driving251

When the brake pads need replacing,
you will hear a distinctive metallic
‘‘screeching’’ sound when you apply
the brakes. If you do not have the
brake pads replaced, they will begin
screeching all the time.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by downshif ting to a lower
gear and taking your f oot of f the
accelerator pedal.
Check your brakes af ter driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Since a
longer distance is needed to stop
with wet brakes, be extra cautious
and alert in your driving.
Your Acura is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The ABS helps
you retain steering control when
braking very hard.
Put your f oot on the brake pedal only
when you intend to brake. Resting
your f oot on the pedal keeps the
brakes applied lightly, causing them
to build up heat. Heat build-up can
reduce how well your brakes work. It
also keeps your brake lights on all
the time, conf using drivers behind
you.
All f our brakes have audible brake
wear indicators.
Your brakes may sometimes squeal
or squeak when you apply them
lightly. Do not conf use this with the
brake wear indicators. The
indicators make a very audible
‘‘screeching.’’ Brake Wear Indicators
The Braking System
Driving262

This section explains the importance
of keeping your vehicle well
maintained and why you should
f ollow basic maintenance saf ety
precautions.
This section also includes
Maintenance Schedules f or normal
driving and severe driving conditions,
a Maintenance Record, and instruc-
tions f or simple maintenance tasks
you may want to take care of
yourself .......................
Maintenance Saf ety .294
.
Important Safety Precautions . 295
.................
Maintenance Schedule . 296
...
Required Maintenance Record . 303
.......
Owner Maintenance Checks . 305
..............................
Fluid Locations .306
......................................
Engine Oil .307
..................................
Adding Oil .307
....................
Recommended Oil .307
..............................
Synthetic Oil .308
....................................
Additives .308
.....
Changing the Oil and Filter . 309
.............................
Cooling System .311
............
Adding Engine Coolant . 311
.......
Replacing Engine Coolant . 313
....................
Windshield Washers .316
....
Automatic Transmission Fluid . 317
..........................
Dif f erential Fluid .318
.............
Transf er Assembly Fluid . 318
....................................
Brake Fluid .319
............................
Brake System .319
..............................
Power Steering .320
.....................
Air Cleaner Element .321
....................................
Hood Latch .323
....................................
Spark Plugs .323
..............................
Replacement .323 ............................
Specif ications .325
...........................................
Battery .326
.................................
Wiper Blades .328
..............
Air Conditioning System . 330
..................
Dust and Pollen Filter . 331
.....................................
Drive Belts .331
....................................
Timing Belt .332
...............................................
Tires .332
......................................
Inf lation .332
..................................
Inspection .334
..............................
Maintenance .335
.............................
Tire Rotation .335
...
Replacing Tires and Wheels . 336
......................
Wheels and Tires .337
..........................
Winter Driving .337
.............................
Snow Tires .338
............................
Tire Chains .338
.............................................
Lights .339
.....................
Headlight Aiming .341
........................
Replacing Bulbs .341
....................
Storing Your Vehicle .349
If you have the skills and tools to per-
f orm more complex maintenance
tasks on your Acura, you may want
to purchase the Service Manual. See
page f or inf ormation on how to
obtain a copy, or see your Acura
dealer.
405
Maintenance
Maint enance293

µ
µÎ
Î
ÎÌ
Ì Ì
ÌÎ
Î
Î
Driving less than 5 miles (8 km)
per trip or, in f reezing
temperatures, driving less than
10 miles (16 km) per trip.
Driving in extremely hot [over
90°F (32°C)] conditions.
Extensive idling or long periods
of stop-and-go driving.
Trailer towing, driving with a
roof top carrier, or driving in
mountainous conditions.
Driving on muddy, dusty, or de-
iced roads.
Follow the Severe Conditions
Maintenance Schedule if you drive
your vehicle
MAINLYunder one or
more of the f ollowing conditions:
Follow the Maintenance
Schedule f or Severe Conditions.
Maint enance
U.S. Owners
Canadian Owners
300
Visually inspect the following items:
Follow this schedule for rear differential
fluid replacement if you use your vehicle
for off-highway driving, trailer towing,
or mainly in stop-and go driving.
Otherwise, use the fluid replacement
schedule in the Maintenance Schedule
for Normal Conditions.
miles x 1,000
km x 1,000
months
Service at the indicated distance or
time whichever comes first.
Replace every 3,750 miles (6,000 km) or 6 monthsCheck oil and coolant at each fuel stop
Every 3 years (independent of mileage)
Rotate tires every 7,500 miles (12,000 km)
Every 7,500 miles (12,000 km) or 6 months
Tie rod ends, steering gear box, and boots
Suspension components
Driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and conditions of fluids
Exhaust system
Fuel lines and connections
Lights and controls
Vehicle underbody 120,000 miles (192,000 km) or 10 years, then every
60,000 miles (96,000 km) or 5 years
15
24
12
30
48
2445
72
3660
96
4875
120 60 90
144 72 105
168
84 120
192
96
Every 7,500 miles (12,000 km) or 6 months
Replace engine oil and oil filter
Check engine oil and coolant
Replace air cleaner element
Use normal schedule except in dusty
conditions
Inspect valve clearance
Replace spark plugs
Replace timing belt and inspect water pump
Inspect and adjust drive belts
Replace engine coolant
Replace transmission fluid
Replace VTM-4 rear differential fluid
Replace transfer assembly fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace dust and pollen filter
Lubricate all hinges, locks and latches
Rotate tires (Check tire inflation and condition at least
once per month) Adjust only if noisy
Refer to page332for replacement
information under special driving
conditions.
Refer to page 331for replacement
information under special driving
conditions.
See page 297.
1:
2:
3:
:
,1
3
2
Maintenance Schedule for Severe Conditions

µ
µ
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Î
Ì Ì
Î
CONT INUED
Maint enance301
Canadian Owners U.S. Owners A, B, C, D
B
C A
D
Use the Maintenance Schedule for Severe Conditions.
3,750 mi/6,000 km
7,500 mi/12,000 km/6 mos
11,250 mi/18,000 km
15,000 mi/24,000 km/1 yr
18,750 mi/30,000 km
22,500 mi/36,000 km
26,250 mi/42,000 km
30,000 mi/48,000 km/2 yrs
33,750 mi/54,000 km
37,500 mi/60,000 km
41,250 mi/66,000 km
3yrs
45,000 mi/72,000 km/3 yrs
48,750 mi/78,000 km
52,500 mi/84,000 km
56,250 mi/90,000 km
60,000 mi/96,000 km/4 yrs
63,750 mi/102,000 km
67,500 mi/108,000 km
71,250 mi/114,000 km Refer to page to determine which schedule to use.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time interval.
Replace engine oil and filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page335).
Inspect tie rod ends, steering gearbox and boots.
Inspect suspension components.
Inspect driveshaft boots.
Replace air cleaner element every 15,000 mi
(24,000 km) under dusty conditions. Otherwise, use
Normal Conditions schedule.
Replace rear differential fluid .
Check parking brake adjustment.
Lubricate all hinges, locks, and latches with
multipurpose grease.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect exhaust system .
Inspect fuel lines and connections .
Check all lights.
Inspect the underbody.
Inspect and adjust drive belts.
Replace transmission fluid.
Replace transfer assembly fluid.
Replace dust and pollen filter .
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
Do items in A.
Replace brake fluid (independent of mileage).
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
Do items in A.
300
3
2
Maintenance Schedule for Severe Conditions (listed by distance/time)