torque Acura MDX 2003 Owner's Manua

........................
Driving Guidelines .250
........................
Preparing to Drive .251 .......................
Starting the Engine .252
Starting in Cold Weather ....................
at High Altitude .252
..............
Automatic Transmission . 253
.
Shif t Lever Position Indicator . 253
................
Shif t Lever Positions . 254
..............
Engine Speed Limiter . 257
....................
Shif t Lock Release . 257
Variable Torque Management ..............................
4WD System .259
..............................
VTM-4 Lock .259
...........................................
Parking .261
.....................
The Braking System .262
.............
Brake Wear Indicators . 262
...............
Brake System Design . 263
.......................
Anti-lock Brakes .263
Important Saf ety .........................
Reminders .264
........................
ABS Indicator .264
Vehicle Stability Assist (VSA) ........................................
System .266
...............
Driving in Bad Weather . 269
...........................
Towing a Trailer .271
Towing Your Vehicle Behind a ................................
Motorhome .283
..............
Of f -Highway Guidelines . 285
This section gives you tips on
starting the engine under various
conditions, and how to operate the
automatic transmission. It also
includes important inf ormation on
parking your vehicle, the braking
system, the VTM-4 System, the VSA
system, and f acts you need if you are
planning to tow a trailer.
Driving
Driving249

This indicator on the instrument
panel shows which position the shif t
lever is in.
Your Acura’s transmission has f ive
f orward speeds, and is electronically
controlled f or smoother shif ting. It
also has a ‘‘lock-up’’ torque converter
forbetterfueleconomy.Youmay
f eel what seems like another shif t
when the converter locks.
The ‘‘D ’’ indicator comes on f or a
f ew seconds when you turn the
ignition switch ON (II). If it f lashes
while driving (in any shif t position),
it indicates a possible problem in the
transmission. Avoid rapid
acceleration and have the
transmission checked by an
authorized Acura dealer as soon as
possible.
The malf unction indicator lamp may
come on along with the ‘‘D ’’
indicator if there is a problem in the
automatic transmission control
system.
5
5Shif t L ever Position Indicator
Automatic Transmission
Driving253

The Variable Torque Management
4WD System (VTM-4) automatically
transf ers varying amounts of engine
torque to the rear wheels.If more traction is needed when your
MDX is stuck or is likely to become
stuck, you can use the VTM-4 Lock
button to increase torque to the rear
wheels when the shif t lever is in the
1, 2 or R position. As soon as this
f eature is no longer needed, press
the VTM-4 Lock button again to
disengage the VTM-4 Lock.
Variable Torque Management 4WD System
Driving
VTM-4 Lock
259
Do not use the VTM-4 Lock button on
dry, paved roads. Driving on dry,
paved roads with VTM-4 Lock ON may
damage the rear dif f erential when
making a turn. Strange noises and
vibration can also result.

To engage the VTM-4 Lock:To disengage the VTM-4 Lock, do
one of the f ollowing:
Press the VTM-4 Lock button.
Move the shift lever to D , D or
D.
Turn the ignition to OFF (0).
When you restart your MDX, the
VTM-4 Lock f eature will be of f .
The VTM-4 Lock will temporarily
disengage when the vehicle speed
exceeds 18 mph (30 km/h). It will
automatically engage again as the
speed slows below 18 mph (30
km/h). The light in the VTM-4 Lock
button will remain on the whole time.
The vehicle speed must be below
18 mph (30 km/h).
Move the shift lever to first (1),
second (2) or reverse (R) gear. To
shif t Reverse f rom Neutral, come
to a complete stop and then shift.
Press the VTM-4 Lock button.
The light in the button will come
on.
To get unstuck, apply light pressure
to the accelerator pedal. Do not spin
the f ront tires f or more than a f ew
seconds. Because of the amount of
torque applied to the rear tires, they
should not spin. This is normal. If
you are not able to get the vehicle to
move, apply the brakes to stop the
wheels, then reverse direction. 1.
2.
3.
34
5
Driving
Variable Torque Management 4WD System
260
Do not continuously spin the f ront tires
of your MDX. Continuously spinning
the f ront tires can cause transmission
or rear dif f erential damage.

When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque:
Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.
Install a rubber hose on the drain
bolt in the back of the engine
block. Loosen the drain bolt. 6.
4. 5. 7.
Cooling Syst em
Maint enance314
DRAIN BOLT
RESERVE TANK
RESERVE
TANK CAP
HOLDER
7 lbf·ft (10 N·m , 1.0 kgf·m)

Put a new washer on the f iller bolt,
then reinstall the f iller bolt. Tighten
it securely. Tightening torque:
The dif f erential should be drained
and ref illed with new f luid according
to the time and distance
recommendations in the
maintenance schedule.
Check the f luid level with the
dif f erential at normal operating
temperature and the vehicle sitting
on level ground. Remove the
dif f erential f luid f iller bolt and
washer, and caref ully f eel inside the
bolt hole with your f inger. The f luid
level should be up to the edge of the
bolt hole. If it is not, slowly add
VTM-4 Dif f erential Fluid until it
starts to run out of the hole. Checkthefluidinthetransfer
assembly with the vehicle sitting on
level ground. Remove the f iller plug
and check that the f luid level is up to
the edge of the f iller plug hole.
Maint enance
Dif f erential Fluid
Transf er Assembly Fluid
Differential Fluid, Transfer Assembly Fluid
318
FILLER BOLT
CORRECT LEVEL FILLER PLUG
DRAIN PLUG
33 lbf·ft (45 N·m , 4.6 kgf·m)

µµ The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If the level is at or
below the MIN mark, your brake
system needs attention. Have the
brake system inspected f or leaks or
worn brake pads.
Check the f luid level in the brake
f luid reservoir monthly.
The brake f luid should be replaced
according to the time recommenda-
tion in the maintenance schedule.
Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 f luid, f rom a sealed
container, as a temporary
replacement. However, the use of
any non-Honda brake fluid can cause
corrosion and decrease the lif e of the
system. Have the brake system
f lushed and ref illed with Honda
Heavy Duty Brake Fluid DOT 3 as
soon as possible.
Brake f luid marked DOT 5 is not
compatible with your vehicle’s
braking system and can cause
extensive damage.
If it is not, slowly add proper f luid
until it starts to run out of the hole.
Reinstall the f iller plug and tighten it
securely.
The transf er assembly f luid should
be drained and ref illed with new f luid
accordingtothetimeanddistance
recommendations in the
maintenance schedule. Viscosity UseaSAE90orSAE80W-90
viscosity hypoid gear oil, API service
classif ied GL4 or GL5 only, in the
transf er assembly. Tightening torque:
Brake System
Brake Fluid
Maint enance
T ransf er A ssembly Fluid, Brake Fluid
319
MAX
MIN
SAE 90: above 0°F ( 18°C)
SAE 80W-90: below 0°F ( 18°C)
33 lbf·ft (45 N·m , 4.6 kgf·m)

Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
af ter it contacts the cylinder head.)
Tightening torque:Install the ignition coil. Reinstall
the hexagon socket head cap bolt.
Push the wire connector onto the
ignition coil. Make sure it locks in
place.
Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.NGK:
DENSO:
8. 9.
11.
12.
10. Specif ications:
Spark Plugs
Maint enance325
13 lbf·ft (18 N·m , 1.8 kgf·m) SKJ16DR-M11 IZFR5K-11
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

Tighten the wheel nuts securely in
the same crisscross pattern. Have
the wheel nut torque checked at
the nearest automotive service
f acility.
Tighten the wheel nuts to:
Remove the center cap from the
flat tire.Place the f lat tire f ace up under
the hoist.
Slowly turn the wheel wrench
clockwisetotakeuptheslackof
the hoist cable. Make sure the
bracketisseatedinthecenter
hole of the spare tire.
Turn the wheel wrench clockwise
until the f lat tire rests against the
underbody of the vehicle and you
hear the hoist click.
Insert the hoist bracket into the
center hole of the f lat tire.
18.
19. 20.
21.
22.
23.
Changing a Flat T ire
T aking Care of t he Unexpect ed366
80 lbf·ft (108 N·m , 11 kgf·m)