battery Acura MDX 2005 User Guide

Each headphone uses one AAA
battery. The battery is under the
cover on the lef t earpiece. To
remove the cover, insert a coin in the
slot and twist it slightly to pry the
cover away f rom the earpiece. Pull
the cover outward, and pivot it out of
the way.
Some state and local government
agencies prohibit the use of
headphones by the driver of a motor
vehicle. Always obey applicable laws
and regulations. The audio f or the rear entertainment
system is sent to the wireless
headphones that come with the
system. When using the headphones,
make sure you wear them correctly:
L (lef t) and R (right) are marked on
the sides of the frame. The antennas
are in the f ront of the earpieces. If
you wear the headphones backwards,
the antennas will be aimed away
from the system, affecting the sound
quality and range.
To use the headphones, pivot the
earpieces outward. This turns them
on. To adjust the volume, turn the
dial on the bottom of the right
earpiece. When you remove the
headphones, the earpieces
automatically pivot inward, and the
headphones turn of f . When not in
use, store the headphones in the
pocket of either f ront seat.
Replacing Bat t eriesWireless Headphones
Rear Entertainment System
142
TAB
VOLUME DIAL

The system will accept auxiliary
inputs f rom standard video games
and video equipment.
Some video game power supplies
may cause poor picture quality.
V=Videojack
L = Lef t audio jack
R = Right audio jack
Auxiliary input jacks and wired
headphone jacks for the rear
entertainment system are under the
third seat armrest on the passenger’s
side. To access these jacks, open the
cover by pulling up on the lever.
Remove the battery. Install the new
battery in the earpice as shown in
the diagram next to the battery slot.
Slide the cover back into place on the
earpiece, then press down on the
back edge to lock it in place.
CONT INUED
Auxiliary Input Jacks
Rear Entertainment System
Features
143
ARMREST
LEVER
AUXILIARY INPUT JACKS
COVER
BATTERY

µ
The HomeLink Universal
Transceiver built into your vehicle
canbeprogrammedtooperateupto
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected. If your garage door
opener was manuf actured bef ore
April 1982, you may not be able to
program HomeLink to operate it.
They do not have the saf ety f eature
that causes the motor to stop and reverse if an obstacle is detected
during closing, increasing the risk of
injury.
Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this inf ormation,
contact the manuf acturer of the
equipment.
If you are training the second or
third buttons, go directly to step 1.If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the first button. To do this,
press and hold the two outside
buttons on the HomeLink
Transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1.
General Inf ormation T raining HomeL ink
Important Saf ety Precautions
HomeL ink Universal T ransceiver
Bef ore you begin
156

To f ind out the status of the phone beingused, do this: To change f rom the currently linked
phone to another paired phone, do this:
To list all paired phones, do this:Press and release the top of the
TALK/BACK button. If you say
‘‘OK’’ af ter the beep, the HFL
response is ‘‘The phone has been
deleted. Returning to the main
menu.’’ If you say ‘‘Go back,’’ or
‘‘Cancel,’’ the phone will not be
deleted. Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Phone setup.’’ The HFL
response is ‘‘Phone setup options
are status, pair, edit, delete, and
list.’’Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Next phone.’’ The HFL
response is ‘‘Searching f or the
next phone.’’ The HFL then
disconnects the linked phone and
searches f or another paired phone.
If no other phones are f ound, the
f irst phone remains linked.
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘List.’’ The HFL
responds by listing the name of
each paired phone. When all
phones paired to the system have
been read, the HFL response is
‘‘The entire list has been read.
Returning to the main menu.’’ Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Phone setup.’’ The HFL
response is ‘‘Phone setup options
are status, pair, edit, delete, and
list.’’ Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Status.’’ An example of
the HFL response is, ‘‘Eric’s phone
is linked. Battery strength is three
bars. Signal strength is f ive bars,
and the phone is roaming.
Returning to the main menu.’’
2.
1. 1.
2. 1.
5.
HandsFreeL ink
Features
167
TM

OnStar uses the Global Positioning
System (GPS) to locate your vehicle
f or f unctions such as route guidance
and roadside assistance. GPS is
af f ected by structures that can
obstruct the signal, such as tunnels,
parking structures, and tall buildings.
It may not be possible f or OnStar to
pinpoint your location if you are in or
near such structures.
OnStar uses cellular technology to
communicate with your vehicle.
Cellular coverage varies by location,
which may af f ect the ability to
establish a connection, or the quality
of the connection.When you turn of f your vehicle’s
ignition, the OnStar system goes into
low-power mode. Af ter 48 hours, it
switches to sleep mode to conserve
your vehicle’s battery power.
Features such as remote door
unlocking and misplaced vehicle
assistance will not work af ter your
vehicle has been parked f or more
than 48 hours.
OnStar
is a registered trademark of
the OnStar Corporation.
OnStar has an antenna on the roof of
the vehicle. To avoid reception
problems, do not cover this antenna.
As required by the FCC: This device complies with Part 15 of the FCC rules.Operation is subject to the f ollowing twoconditions: (1) This device may notcause harmf ul interf erence, and (2) thisdevice must accept any interf erencereceived, including interf erence thatmay cause undesired operation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210. Operation issubject to the f ollowing two conditions:(1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.System Limitations
OnSt ar
184

Apply the parking brake.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.
Make sure the shif t lever is in
Park. Press on the brake pedal.Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. Do not hold
the key in START (III) f or more
than 15 seconds at a time. If the
engine does not start right away,
pause f or at least 10 seconds
bef ore trying again.If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed halfway
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.
If the engine still does not start,
press the accelerator pedal all the
way down and hold it there while
starting in order to clear f looding.
If the engine still does not start,
return to step 5.
5.
6.
1.
2.
3.
4.
Starting the Engine
Driving
199
Immobilizer System T he immobilizer system protects your
vehicle f rom thef t. If an improperly-
coded key (or other device) is used, the
engine’s f uel system is disabled. See
on page .
The engine is harder to start in cold
weather. Also, the thinner air f ound at
altitudes above 8,000 f eet (2,400
meters) adds to this problem.
80

µµµµµ µ
CONT INUED
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page .
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can remove the key
from the ignition switch. Press the brake
pedal, making sure to keep your f oot
of f the accelerator pedal, then shif t
f rom Park to Reverse. To shif t f rom
Neutral to Reverse, come to a
completestopandthenshift. Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press the
brake pedal, making sure to keep
your f oot of f the accelerator pedal,
when you are moving the shif t lever
f rom Neutral to another gear.
Your vehicle has a reverse lockout so
you cannot accidentally shif t to
Reverse from Neutral or any other
driving position when the vehicle
speed exceeds 7 9 mph (12 14
km/h).
If you cannot shif t to Reverse when
the vehicle is stopped, press the
brake pedal and slowly shift to
Neutral, and then to Reverse.
If there is a problem in the reverse
lockout system, or your vehicle’s
battery is disconnected or goes dead,
you cannot shif t to Reverse. (Ref er
to
on page ). Use this position f or
normal driving. The transmission
automatically selects a suitable gear
f or your speed and acceleration. You
may notice the transmission shif ting
up at higher speeds when the engine
is cold. This helps the engine warm
up f aster.
203
203
Automatic Transmission
Park (P)Shif t L ock Release Reverse (R)
Neutral (N)
Shif t L ock Release Drive (D )
5Driving
201

Your MDX can be towed behind a
motorhome at legal highway speeds
up to 65 mph (100 km/h). Do not
exceed 65 mph (100 km/h) or severe
transmission damage will occur. To
avoid damage to the 4WD system, it
must be towed with all f our wheels
on the ground (f lat towing).
When purchasing a tow bar, make
sure you select a reputable
manuf acturer. Follow the
manufacturer’s attachment
instructions caref ully.
Perf orm this procedure every day
immediately bef ore you begin towing.
Otherwise, severe automatic
transmission damage will occur.Start the engine. Check the transmission f luid level
(see page ). Press on the brake pedal. Shif t the
lever through all the positions (P,
R,N,D,D,D,2,1).
ShifttoD ,thentoN.Letthe
engine run f or three minutes, then
turn it off.
Release the parking brake.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock.
Make sure the radio and any items
plugged into the accessory power
sockets are turned of f so you do
not run down the battery.
If you tow more than 8 hours in one
day, you should repeat the above
procedure at least every 8 hours
(when you stop f or f uel, etc.)
242
543 5
Ext ended T owing
Towing Your Vehicle Behind a Motorhome
222
The steering system can be damaged if
the steering wheel is locked. Leave the
ignition switch in the ACCESSORY (I)
position, and make sure the steering
wheel turns f reely bef ore you begin
towing.

This section explains why it is
important to keep your vehicle well
maintained and how to f ollow basic
maintenance saf ety precautions.
This section also includes
Maintenance Schedules f or normal
driving and severe driving conditions,
a Maintenance Record, and instruc-
tions f or simple maintenance tasks
you may want to take care of
yourself .
If you have the skills and tools to per-
f orm more complex maintenance
tasks on your vehicle, you may want
to purchase the Service Manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer.......................
Maintenance Saf ety .228
.................
Maintenance Schedule . 229
....................
Maintenance Record .233
..............................
Fluid Locations .236
........................
Adding Engine Oil .237
.........
Changing the Oil and Filter . 238
..............................
Engine Coolant .240
....................
Windshield Washers .241
....
Automatic Transmission Fluid . 242
....................................
Brake Fluid .243
....................
Power Steering Fluid . 244
....................................
Timing Belt .244
.............................................
Lights .245
................
Cleaning the Seat Belts . 249
.....................................
Floor Mats .249
.................................
Wiper Blades .250
...............................................
Tires .252
...................
Checking the Battery . 257
.............................
Vehicle Storage .258
299
Maintenance
Maint enance
227

To eliminate potential hazards, read
the instructions bef ore you begin,
and make sure you have the tools
and skills required.Make sure your vehicle is parked
on level ground, the parking brake
is set, and the engine is of f .
To clean parts, use a commercially
available degreaser or parts
cleaner, not gasoline.
To reduce the possibility of f ire or
explosion, keep cigarettes, sparks,
and f lames away f rom the battery
and all f uel-related parts. Wear eye protection and
protective clothing when working
with the battery or compressed air.
Be sure there is
adequate ventilation whenever you
operate the engine.
Let the
engine and exhaust system cool bef ore touching any parts.
Do
not run the engine unless
instructed to do so.
Some of the most important saf ety
precautions are given here. However,
we cannot warn you of every
conceivable hazard that can arise in
perf orming maintenance. Only you
can decide whether or not you
should perf orm a given task.
All service items not detailed in this
section should be perf ormed by a
certif ied technician or other qualif ied
mechanic.
Maintenance Saf ety
Important Saf ety Precautions
Potential Vehicle HazardsCarbon Monoxide poison f rom
engine exhaust.
Burns f rom hot parts. Injury f rom moving parts.
228
Failure to properly follow
maintenance instructions and
precautions can cause you to
be seriously hurt or killed.
Always follow the procedures
and precautions in this owner’s
manual.
Improperly maintaining this
vehicle or failing to correct a
problem before driving can
cause a crash in which you can
be seriously hurt or killed.
Always follow the inspection
and maintenance
recommendations in this owner’s
manual.