steering wheel Acura MDX 2007 User Guide

ÛÝÛÝ
Memory Position Link
If ‘‘MEMORY POSITION LINK’’ is
set to ‘‘ON,’’ the driver’s seat, the
steering wheel, and outside mirror
positions move to the position stored
in the memory when you open the
driver’s door, using the remote
transmitter.
You can choose this customize item
f rom ‘‘POSITION SETUP’’ by
pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘MEMORY POSITION LINK’’ and
repeat the procedure again.
Multi-Inf ormation Display
98
——y

y
()-y
y

ÛÝÛÝ
CONT INUED
Auto Tilt & Telescope Steering Wheel
When ‘‘AUTO TILT & TELESCOPE
STEERING WHEEL’’ is set to ‘‘ON,’’
the steering wheel automatically
moves f ully in and up when you turn
the ignition switch to the LOCK (0)
position and remove the key.
You can choose this customize item
f rom ‘‘POSITION SETUP’’ by
pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
TILT & TELESCOPE STEERING
WHEEL’’ and repeat the procedure
again.
Multi-Inf ormation Display
Inst rument s and Cont rols
99
——y

y
()-y
y

ÎÎ
Î Î
Î
Î
To use the horn, press the center pad of the steering wheel.
:
If equipped
1:
Controls Near the Steering Wheel
Instru me ntsand Cont ro ls
115
DRIVING POSITION
MEMORY SYSTEM
VEHICLE
STABILITY
ASSIST SYSTEM
OFF SWITCH
REAR WINDOW
DEFOGGER
HAZARD
WARNING
BUTTON
HEADLIGHT
WASHER
SWITCH
ACTIVE DAMPER
SYSTEM SWITCH
MIRROR
CONTROLS
POWER TAILGATE
BUTTON PASSENGER
AIRBAG
OFF INDICATOR
INSTRUMENT
PANEL
BRIGHTNESS
WINDSHIELD
WIPERS/WASHERS
STEERING
WHEEL
AUDIO CONTROLS
FUEL FILL DOOR
RELEASE BUTTON
CRUISE CONTROL
BUTTONS
HORN
HEADLIGHT/TURN
SIGNAL/
FRONT FOG LIGHTS
POWER DOOR LOCK
MASTER SWITCH
POWER WINDOW
SWITCHES
STEERING WHEEL
ADJUSTMENTS SEAT HEATER
SWITCHES
HOOD RELEASE
HANDLE
(P.117)
(P.352)
(P.153)
(P.147)
(P.317) (P.132) (P.319) (P.353)
(P.266) (P.146)(P.164)
(P.122)
(P.122) (P.34) (P.123)
(P.116)
(P.229)
(P.118)
(P.124)
(P.155)
(P.130) ACCESSORY POWER
SOCKETS
1
——y

y
()-y
y

µ
When you turn the wiper switch to
the ‘‘OFF’’ position, the wiper will
return to its parked position.
Rotate the switch
clockwise to turn the rear window
wiper ON. The wiper operates
intermittently.
The headlight washers can be
operated at any time by pressing the
headlight washer button located next
to the steering wheel column. The
headlights must be turned on to use
this button. In addition, the headlight
washer operates when the
windshield washers are f irst turned
on. The headlight washers use the same
f luid reservoir as the windshield
washers.
1.
2.
CONT INUED
Windshield Wipers and Washers
Headlight Washers(On Canadian models)Rear Window Wiper and Washer
ON
Inst rument s and Cont rols
117
——y

y
()-y
y

Make any steering wheel
adjustments before you start driving.Move the steering wheel in, out, up,
or down by pushing and holding the
adjustment switch in that direction.Release the switch when the
steering wheel reaches the desired
position. Make sure the steering
wheel points towards your chest, not
toward your face, and that you can
see the instrument panel gauges and
indicators.
Steering Wheel A djustments
124
ADJUSTMENT SWITCH
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
——y

y
()-y
y

When you remove the key from the
ignition switch, the steering wheel
au tomatically moves fully in and up. If
your vehicle’s battery is
disconnected or goes dead, or the
fuse for the power tilt and telescopic
steering wheel is remove d, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the fuse.
Insert the key into the ignition
switch, and remove it. The steering
wheel automati cally moves fully in
and up to let you know the system is
reset.
To
change the ‘‘AUTO TILT &
TELESCOPE STEERING WHEEL’’
setting, see page .
The steering wheel then returns to
its original position when you insert
the key back in the ignition switch.
Steering wheel movement is also
controlled by the driving position
memory system (see page ). 155
99
Steering Wheel A djustments
Inst rument s and Cont rols
125
——y

y
()-y
y

µµ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
You can insert or
remove the key only in this position.
To turn the key to the LOCK (0)
position, the shif t lever must be in
Park, and you must push the key in
slightly. If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key. You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or the
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn of f the beeper.
TheshiftlevermustbeinPark
bef ore you can remove the key f rom
the ignition switch.
Ignition Switch
LOCK (0)
A CCESSORY (I)
ON (II)
ST A RT (III)
Inst rument s and Cont rols
129
——y

y
()-y
y

Here are the settings activated with
the remote;
Driving position memory
(see page ).
When you unlock the driver’s door
with your remote, each remote
activates the keyless memory
settings related to that remote. The
driver’s ID (MEMORY 1 or
MEMORY 2) is shown on the back
of each remote. You
will also see the ‘‘WELCOME
DRIVER 1’’ or ‘‘WELCOME
DRIVER 2’’ message on the multi-
info rmation display, dep ending on
which linked remote transmitter is
used.
To turn off this feature, press and
hold the LOCK and UNLOCK
buttonsatthesametime.TheLED
in the remote will blink twice. Then
release the buttons. Doing this
cancels the keyless memory settings
for that remote and restores the
default settings.
To turn the keyless memory settings
back on, repeat this procedure. The
LED will blink once to indicate the
fe ature has been turned on.
The steering wheel will move to the
stored position when you insert the
key into the ignition switch.
When
you unlock and open the
driver’s door with the remote
transmitter, the driver’s seat (except
the power lumbar feature) and
outside mirrors start to move to the
positions stored in memory. The
indicator in the related memory
button to the remote comes on.
Audio
system settings
(see page ).
Climate control settings
(see page ).
Customized
settings
(see page ). 83
155 198 169
K eyless Memory Settings
Remote Transmitter
Inst rument s and Cont rols
139
TM
——y

y
()-y
y

Adjust the seat to a comfortable
position (see page ).
Store
a driving position only when
the vehicle is parked.
Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Your
vehicle has a memory feature
for the steering wheel, driver’s seat,
and outside mirror positions.
Seat, except for power lumbar,
steering wheel and outside mirror
positionscanbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Driver 1 or
Driver 2). For more information see
page .
Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current positions of the driver’s
seat, steering wheel, and outside
mirrors are now stored.
Adjust
the steering wheel to a
comf ortable position (see page ).
Adjust the outside mirrors f or best
visibility (see page ). 3.
1.
2.
139
124140
153
CONT INUED
Storing a Driving Position in
Memory
Driving Position Memory System
Inst rument s and Cont rols
155
MEMO BUTTON
MEMORY BUTTONS
——y

y
()-y
y

Doing any of the following after
pressing the MEMO button will
cancel the storing procedure.
Not pressing a memory button
wi thin 5 seconds.
Readjusting the seat position.
Readjust the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. To
select a memorized position, do
this: To
stop the system’s automatic
ad justment, do any of these actions:
Press any button on the control
panel: MEMO, 1, or 2.
Push any of the adjustment
switches for the seat.
Shift out of Park.
Adjust the outside mirrors.
Make
sure the vehicle is parked.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
To change the ‘‘MEMORY
POSITION LINK’’ setting, see page . If desired, you can use the
adjustment switches to change the
positions of the seat, steering wheel
or outside mirrors af ter they are in
their memorized position. If you
change the memorized position, the
indicator in the memory button will
go out. To keep this driving position
f or later use, you must store it in the
driving position memory.
The system will move the seat,
steering wheel, and outside mirrors
to the memorized positions. The
indicator in the selected memory
button will f lash during movement.
When the adjustments are complete,
you will hear two beeps, and the
indicator will remain on. 1.
2.
98
Selecting a Memorized Position
Driving Position Memory System
156
——y


y
()-y

y