start stop button Acura RDX 2009 Owner's Manual

To load a single disc:Press and release the LOAD
button on the changer unit. You
will see ‘‘BUSY’’ on the center
display, and the disc load indicator
turns red and starts blinking.
Insert a disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display at the same time.
Insert the disc only about half way;
the drive will pull it in the rest of
the way. You will see the disc
indicator blinking on the center
display.
To load multiple discs in one
operation:
When the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display again, insert the
next CD in the slot.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
Repeat steps 1 through 3 until all
six positions are loaded. If you are
not loading all six positions, press
the LOAD button again after the
last CD has loaded. ‘‘DISC READ’’
appears on the center display, then
the system begins playing the last
CD loaded.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 10 seconds, stop the load
operation, and begin playing the last
disc loaded.
Press and hold the LOAD button
on the changer unit until you hear
a beep. You will see ‘‘BUSY’’ on
the center display, and disc load
indicator turns red and starts
blinking.
Insert the disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display at the same time.
Insert it only half way; the drive
will pull it in the rest of the way.
You will see ‘‘BUSY’’ on the center
display, and the disc load indicator
turns red again and blinks as the
CD is loaded.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
1.
2.
3.
1.
2. 4.
Audio System
L oading CDs in the Changer
176
\f—\f—

y
y
() \fy\f

y
2009 RDX

µ
CONT INUED
The CD changer can play CD-Rs and
CD-RWs compressed in MP3 and
WMA format. When playing a disc in
MP3 or WMA, you will see ‘‘MP3’’ or
‘‘WMA’’ on the center display. A disc
can support more than 99 f olders,
and each folder can hold up to 255
playable f iles.
When there are more than 99 f olders
in a disc, the center display only
shows two digits.
Youwillsee‘‘DISCREAD’’onthe
center display, then the system
begins to play the CD.
You can load a disc(s) in any mode
(AM, FM, XM, or AUX) if you do not
select an empty position.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded.
You can load a CD into an empty
position while a CD is playing. Select
the empty position (the disc
indicator is not shown on the center
display) by pressing the appropriate
side of the preset bars. The current
CD stops playing and starts the
loading sequence. The CD just
loaded will play. Select the CD changer by pressing
the CD/AUX button. You will see
‘‘CD’’ on the center display. The
system will begin playing the last
selected CD in the CD changer. You
will see the disc and track numbers
displayed.
When the system reaches the end of
the disc, the system will advance to
the next disc and begin to play. To
select a dif f erent disc, press an
appropriate side of the preset bar (1
6). If you select an empty position
in the CD changer, the system will
try to load the CD in the empty slot. If a f ile on an MP3 or WMA
disc is protected by digital rights
management (DRM), the audio unit
displays FORMAT, and then skips to
the next f ile.
If the disc has a complex structure, it
will take a while to read the disc
before the system begins to play it.
3.
Audio System
Playing an MP3/WMA Disc
To Play a CD
Features
177
NOTE:
\f—\f—

y
y
() \fy\f
y
2009 RDX

CONT INUED
To load a single disc:Press and release the LOAD
button on the changer unit. You
will see ‘‘BUSY’’ on the upper
display, and the disc load indicator
turns red and starts blinking.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 10 seconds, stop the load
operation, and begin playing the last
disc loaded. Repeat steps 1 through 3 until all
six positions are loaded. If you are
not loading all six positions, press
the LOAD button again after the
last CD has loaded. ‘‘DISC READ’’
appears on the upper display, then
the system begins playing the last
loaded.
When the disc load indicator turns
green and ‘‘LOAD’’ appears on the
upper display again, insert the
next CD in the slot. Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
Insert the disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears in the
upper display at the same time.
Insert it only half way; the drive
will pull it in the rest of the way.
You will see ‘‘BUSY’’ on the upper
display, and the disc load indicator
turns red again and blinks as the
CD is loaded.
Press and hold the LOAD button
on the changer unit until you hear
a beep. You will see ‘‘BUSY’’ on
the upper display, and the disc
load indicator turns red and starts
blinking.
To load multiple discs in one
operation:
‘‘DTS’’ and ‘‘DTS Digital Surround’’
are registered trademarks of Digital
Theater Systems, Inc. 1.
2.
3.4.
1.
Audio System
L oading CDs in the Changer
Features
199
\f—\f—

y
y
() \fy\f\fy
2009 RDX

You can also select the empty
position by pressing the appropriate
preset button.
You can load a disc(s) in any mode
(AM, FM, XM, or AUX) if you do not
select an empty position.
You cannot select the empty position
if there is no disc in the changer.
You can load a CD into an empty
position while a CD is playing. Press
the AUDIO button to view the audio
control display. Select the empty
position (‘‘No Disc’’ is shown on the
audio control display) by rotating the
interf ace dial. Then press ENTER on
the selector to enter your selection.
The current CD stops playing and
starts the loading sequence. The CD
just loaded will play.
Insert a disc into the disc slot
when the disc load indicator turns
green, and ‘‘LOAD’’ appears on
the upper display at the same time.
Insert the disc only about half way;
the drive will pull it in the rest of
theway.Youwillseethedisc
number blinking on the upper
display, and the disc load indicator
turns red again and blinks as the
CD is loaded.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
Youwillsee‘‘DISCREAD’’onthe
upper display, then the system
begins to play the CD.
2.
3.
Audio System
200
EMPTY POSITION
\f—\f—

y
\fy
() \fy\f\fy
2009 RDX

µµµ
If you have done all of the above and
still cannot move the lever out of
Park, see on
page . This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Press the release
buttononthefrontof theshiftlever
to move it.
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. You must also press the
release button to shift into Park. The
shif t lever must be in Park bef ore
you can remove the key f rom the
ignition switch. Press the brake
pedal and press the release button
on the f ront of the shif t lever to shif t
f rom Park to reverse. To shif t f rom
reverse to neutral, come to a
completestop,andthenshift.Press
the release button bef ore shif ting
into reverse f rom neutral.
Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press on the
brake pedal when you are moving
the shift lever from neutral to
another gear.
296To shift from:
PtoR
RtoP
NtoR DtoS
StoD
DtoN
NtoD RtoN Do this:
Press the brake pedal, and
press the shift lever release
button.
Press the shift lever release
button.
Move the shift lever.
Automatic Transmission
Shif t L ock Release
Park (P) Reverse (R)
Neutral (N)
294
\f—\f—

y
\fy
() \fy\fy
2009 RDX

´µ
When you move the shif t lever f rom
‘‘D’’ to ‘‘S’’ position and pull either
paddle shif ter, the gear position
indicator displays ‘‘M’’ along with the
selected gear number.
To upshif t, pull the (right) paddle
shif ter. To downshif t, pull the
(lef t) paddle shif ter. When you accelerate f rom a stop,
the transmission starts in f irst gear,
and you must manually upshif t
between f irst and f if th gears. Make
sure you upshif t bef ore the engine
speed reaches the tachometer’s red
zone.
The transmission remains in the
selectedgear(5,4,3,2,or1).There
is no automatic downshif t when you
push the accelerator pedal to the
f loor.
When you are driving in 4th or 5th
gear, the transmission downshifts to
the lower gear under the f ollowing
conditions:
The vehicle slows down to a
certain speed.
You press the brake pedal.
With the shif t lever in S position, you
can select the sequential shif t mode
to shif t gears; much like a manual
transmission using the paddle
shif ters, but without a clutch pedal.
To enter the sequential shif t mode,
pressthereleasebuttononthefront
of the shift lever, move the lever to
the S position, then pull either paddle
shif ter. To cancel the sequential shif t
mode and return to the ordinary
automatic transmission, move the
shif t lever f rom the S position. When
moving the shift lever, be careful not
to operate incorrectly. While you are
driving in the sequential shif t mode,
the transmission will not
automatically return to ordinary
automatic transmission.
CONT INUED
Using the Paddle Shif ters in S
position (Sequential Shif t Mode)
Driving with the Paddle Shif ters
Driving
299
‘‘M’’ INDICATOR
GEAR POSITION INDICATOR
\f—\f—

y
y
() \fy\f\fy
2009 RDX