instrument panel Acura RL 2000 3.5 User Guide

Control
s Nea r th e Steerin g Whee l

Windshiel d Washer s
To clean the windshield, pull back on
the wiper control lever. The washers spray until you release the lever. The
wipers run at low speed while you're pulling the lever, then complete one
more sweep of the windshield after
you release it.
Hazar
d Warnin g

Push the red button to the left of the
clock to turn on the hazard warning
lights (four-way flashers). This causes all four outside turn signalsand both indicators in the instrument
panel to flash. Use the hazard
warning lights if you need to park in a dangerous area near heavy traffic,
or if your car is disabled. Car
s wit h navigatio n syste m
Instrument s an d Control s

Control
s Nea r th e Steerin g Whee l

1. Locate the adjustment switch on the left side of the steering column.Move the steering wheel, in, out,
up, or down by pushing and
holding the adjustment switch in
that direction. 2. Release the switch when the
steering wheel reaches thedesired position. Make sure the
steering wheel points towards
your chest, not toward your face, and that you can see the
instrument panel gauges and
warning lights.
Automatic Movement

AUTO SWITC H
The AUTO switch controls automat- ic movement of the steering wheel.
When this switch is in the ON posi- tion, the steering wheel automatical-
ly moves fully in and up when you re-move the key from the ignition
switch.

Instrument s an d Control s

Steerin
g Whee l Control s

3. Press and release the SET/decel button on the steering wheel. TheCRUISE CONTROL light on the
instrument panel comes on to show the system is now activated. The cruise control may not hold the
set speed when you are going up and
down hills. If your speed increases
going down a hill, use the brakes to slow down to the desired speed. This
will cancel the cruise control. To resume the set speed, press the
RESUME/accel button. The
CRUISE CONTROL light on the
instrument panel comes on.
When climbing a steep hill, the automatic transmission may
downshift to hold the set speed. Changing the Set Speed
You can increase the set cruising
speed in any of these ways: Press and hold the RESUME/
accel button. The car will acceler- ate. When you reach the desired
cruising speed, release the button. Push on the accelerator pedal. Ac-
celerate to the desired cruising
speed and press the SET/decel
button. To increase your speed in very
small amounts, tap the RESUME/
accel button repeatedly. Each time
you do this, your car will speed up about 1 mph (1.6 km/h).

Instrument s an d Control s

RESUME
/

acce l

BUTTO N

SET/dece l
BUTTO N

Steerin
g Whee l Control s

You can decrease the set cruising speed in any of these ways: Press and hold the SET/decel
button. The car will decelerate. Release the button when you
reach the desired speed. Tap the brake pedal lightly with
your foot. The CRUISE CONTROL light on the
instrument panel will go out.
When the car slows to the desired speed, press the SET/decel button.
The car will then maintain the desired speed.
To slow down in very small amounts, tap the SET/decel
button repeatedly. Each time you do this, your car will slow down
about 1 mph (1.6 km/h). Even with the cruise control turned
on, you can still use the accelerator
pedal to speed up for passing. After
completing the pass, take your foot
off the accelerator pedal. The car
will return to the set cruising speed.
Resting your foot on the brake pedal
will cause the cruise control to
cancel.
Cancelling the Cruise Control

CANCEL

BUTTO N

You can cancel the cruise control in any of these ways:
Tap the brake pedal. Push the CANCEL button on the

steering wheel.

Press the Cruise Control Master

Switch.

Instrument s an d Control s

CONTINUED

Steerin
g Whee l Control s

When you push the CANCEL button, or tap the brake pedal, the CRUISE
CONTROL light on the instrument
panel will go out and the car will
begin to slow down. You can use the accelerator pedal in the normal way.
The system remembers the previously-set cruising speed. To
return to that speed, accelerate toabove 25 mph (40 km/h) and then
press and release the RESUME/ accel button. The CRUISE
CONTROL light comes on. The car
will accelerate to the same cruising speed as before. Pressing the Cruise Control Master
Switch turns the system completely
off and erases the previous cruising
speed from memory. To use the
system again, refer to Using the

Cruise Control.
Remot
e Audi o Control s

AUDIO/C H

BUTTO N

These buttons let you control some functions of the audio system with-out removing your hands from the
wheel. Refer to page 161 for a com- plete explanation.
Instrument s an d Control s

Key
s an d Lock s

Ignitio n Switc h

The ignition switch is on the right side of the steering column. It has
four positions: LOCK (0)
ACCESSORY (I)
ON (II)
START (III) LOC
K (0 ) — You can insert or
remove the key only in this position.
To switch from ACCESSORY to LOCK, you must push the key inslightly as you turn it. The shift lever
must also be in Park. The anti-theft
lock will lock the steering column
when you remove the key.
If the front wheels are turned, the
anti-theft lock may sometimes make
it difficult to turn the key from
LOCK to ACCESSORY. Firmly turn
the steering wheel to the left or to
the right as you turn the key.
ACCESSOR Y (I ) — In this position,
you can operate the audio system and the cigarette lighter.
O N (II ) — This is the normal key
position when driving. All features
and accessories on the car are usable.
Several of the lights on the instru-
ment panel come on as a test when
you turn the ignition switch from ACCESSORY to ON.
STAR T (III ) — Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key.
The engine will not start if the Immobilizer System does not
recognize the key's coding (see page 78).
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or
ACCESSORY (I) position and open the driver's door. Remove the key to
turn off the beeper.

Instrument s an d Control s

Drivin
g Positio n Memor y Syste m

Your Acura has a memory feature for the steering wheel, driver's seatand outside mirror positions.
Two seat, steering wheel, and outside mirror positions, for
different drivers or driving
conditions, can be stored in separate
memories. You select a memorized
position by pushing the appropriate

button.
Storing a Driving Position in Memory
Store a driving position as explained
in this section only when the car is

parked.

1. Turn the ignition switch ON (II). You cannot add a new drivingposition in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
2. Adjust the seat to a comfortable position (see page 93). Adjust
the steering wheel to acomfortable position (see page 71).

Adjust the outside mirrors for best

visibility (see page 98).
MEM
O BUTTO N
3. Press and release the MEMO button on the control panel. You
will hear a beep. Immediatelypress and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. Thecurrent positions of the driver's

seat, steering wheel, and outside

mirrors are now stored.
Instrument s an d Control s

Drivin
g Positio n Memor y System , Sea t Heater s

To stop the system's automatic ad-
justment; Press any button on the control
panel: MEMO, 1 or 2. Push any of the adjustment
switches for the seat or steering
wheel. Shift out of Park.
Adjust the outside mirrors.
If you select a memorized position
without inserting the key in the ignition switch, only the seat and
outside mirrors will adjust. To get
the system to also adjust the steering
wheel, insert the key in the ignition switch. You will hear two beeps
when it is complete. If desired, you can use the adjust-
ment switches to change the posi-
tions of the seat, steering wheel or outside mirrors after they are in
their memorized position. To keep
this driving position for later use,
you must store it in the driving posi-
tion memory. Sea
t Heater s

SEAT HEATER S

Both front seats are equipped with seat heaters. The ignition switch
must be ON (II) to use them. Push
the front of the switch, HI, to rapidly heat up the seat. After the seat
reaches a comfortable temperature,select LO by pushing the back of the
switch. This will keep the seat warm.
Instrument s an d Control s

Powe
r Window s
Your car's windows are electrically- powered. Turn the ignition switch to ON (II) to raise or lower any window.
Each door has a switch that controls
its window. To open the window,
push the switch down and hold it.
Release the switch when you want
the window to stop. Close the
window by pulling back on the switch and holding it. DRIVER'
S WINDO W SWITC H
MAI N SWITC H
The driver's door armrest has a master power window control panel.
To open any of the passengers' win- dows, push down on the appropriate
switch and hold it down until the
window reaches the desired position.
To close the window, pull back on the window switch. Release the switch when the window gets to the
position you want.

CONTINUED

Instrument s an d Control s
Closing a power window on
someone's hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.

Powe
r Windows , Moonroo f

The master control panel also con- tains these extra features:
AUT O — To open the driver's
window fully, push the window switch firmly down and release it.
The window automatically goes all the way down. To stop the window
from going all the way down, pull
back on the window switch briefly.
To open the driver's window only partially, push the window switchdown lightly and hold it. The window
will stop as soon as you release the
switch.

The AUTO function only works to lower the driver's window. To raise
the window, you must pull back on
the window switch and hold it until the window reaches the desired

position.
The MAIN switch controls power to
the passengers'windows. With thisswitch off, the passengers'windows
cannot be raised or lowered. The
MAIN switch does not affect the driv- er's window. Keep the MAIN switch
off when you have children in the carso they do not injure themselves by
operating the windows unintentional-
ly. The lights inside the switches come on when you turn the parking
lights or headlights on.
The power window system has a key- off delay function. The windows willstill operate for up to ten minutes
after you turn off the ignition. Opening either front door cancels
the delay function. You must turn
the ignition switch ON (II) again
before you can raise or lower the
windows. There are two switches on the
ceiling near the front ceiling light.
The ignition switch must be ON (II).
To open the moonroof, pull the OPEN/CLOSE switch backward and
hold it until the moonroof reaches the desired position.
Instrument s an d Control s Moonroo
f

OPEN/CLOS E

SWITC H