ignition Acura RL 2001 3.5 Owner's Guide

Keys and Locks
Keys

Your car comes with two master keys and a valet key.
The master key fits all the locks on your car:
Ignition

Doors

Trunk
Trunk pass-through cover
Glove box

The valet key works only in the
ignition and the door locks. You can
keep the trunk, trunk pass-through cover, and glove box locked when
you leave your car and the valet key at a parking facility.
You should have received a key number plate with your keys. You
will need this key number if you ever
have to get a lost key replaced. Keep
the plate stored in a safe place. If you need to replace a key, use only an
Acura-approved key blank.
These keys contain electronic circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the circuits are damaged. Protect the keys from direct
sunlight, high temperature, and
high humidity. Do not drop the keys or set heavy
objects on them.
Keep the keys away from liquids.
If they get wet, dry them immedi-
ately with a soft cloth.
The keys do not contain batteries. Do not try to take them apart.

CONTINUED

Instruments and Controls

KEY

NUMBER

PLATE
MASTER

KEYS

(Black)
VALET

KEY

(Gray)

Keys and Locks
Remote Transmitter

Your car also comes with two remote
transmitters; see page 82 for anexplanation of the operation.

Learning Key

You should also receive a small case containing a learning key. It is used
by the Acura dealer to code replace-
ment keys to your car's Immobilizer
System. It must not be used in your
car's ignition switch. Store the learn-
ing key with the key number plate in a safe place. If you attempt to use the learning
key to start your car's engine, it may cause a malfunction in the system
that makes your master and valet
keys unusable. If this happens, you should contact your Acura dealer.
If you need a new key made, take the
key number plate, the learning key, and all other keys that came with
your car to your Acura dealer. Immobilizer System
The Immobilizer System protects your car from theft. A properly- coded master or valet key must be
used in the ignition switch for the engine to start. If an improperly-
coded key (or other device) is used,
the engine's fuel system is disabled.
When you turn the ignition switch to ON (II), the Immobilizer System
indicator should come on for a few seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again.

Instruments and Controls

Keys and Locks

The system may not recognize your key's coding if another immobilizer
key or other metal object is near the ignition switch when you insert the
key. To make sure the system
recognizes the key code: Do not keep other immobilizer
keys on the same key ring.
Use a plastic or leather key fob,
not metal.
Keep other keys away from your
vehicle's key and the ignition switch while trying to start the

engine.

If the system repeatedly does not
recognize the coding of your key,
contact your Acura dealer.
This indicator will also blink several times when you turn the ignitionswitch from ON (II) to ACCESSORY (I) or LOCK (0). Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your car undriveable.
If you have lost your key and you
cannot start the engine, contact your
Acura dealer.
As required by the FCC:
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired

operation.

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
This device complies with Industry

Canada Standard RSS-210.

Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference that may cause
undesired operation of the device.
Instruments and Controls

Keys and Locks

Ignition Switch

The ignition switch is on the right side of the steering column. It has
four positions:
LOCK (0)
ACCESSORY (I) ON (II)
START (III) LOCK (0) — You can insert or
remove the key only in this position.
To switch from ACCESSORY to LOCK, you must push the key in
slightly as you turn it. The shift lever
must also be in Park. The anti-theft
lock will lock the steering column
when you remove the key.
If the front wheels are turned, theanti-theft lock may sometimes make
it difficult to turn the key from LOCK to ACCESSORY. Firmly turn
the steering wheel to the left or to
the right as you turn the key.
ACCESSORY (I) — In this position, you can operate the audio systemand the cigarette lighter.
ON (II) — This is the normal key
position when driving. All features and accessories on the car are usable.
Several of the lights on the instru-
ment panel come on as a test when
you turn the ignition switch from ACCESSORY to ON.
START (III) — Use this positiononly to start the engine. The switch
returns to ON (II) when you let go of
the key.
The engine will not start if the Immobilizer System does not
recognize the key's coding (see page 78).
You will hear a reminder beeper if
you leave the key in the ignition switch in the LOCK (0) or
ACCESSORY (I) position and open the driver's door. Remove the key to
turn off the beeper.
Instruments and Controls

Keys and Locks

Power Door Locks
Each front door has a master door
lock switch. Either switch locks and
unlocks all doors. Push the switch down to lock all doors, and up to

unlock them.
Each door has a lock tab at the top of
the door. When you push down the lock tab on the driver's door, alldoors lock. Pulling up the lock tab on
the driver's door only unlocks that door. The lock tab on each

passenger's door only locks and

unlocks that door.
To lock any passenger's door when
getting out of the car, push the locktab down and close the door. To lock
the driver's door, remove the key
from the ignition switch and push the lock tab down or push the master switch down, then close the door.
All doors can be locked from the outside by using the key in either
front door. To unlock only the driver's door from the outside, insert the key
in the driver's door lock, turn the key
and release it. If you turn the key and hold it, all doors will unlock. All
four doors will unlock when you unlock the passenger's door with the
key.

CONTINUED

Instruments and Controls
LOCK TAB
MASTER DOOR LOCK SWITCH

Keys and Locks

Lockout Prevention

If you forget and leave the key in the
ignition switch, Lockout Prevention
will not allow you to lock the driver's door. With the driver's door open
and the key in the ignition, both
master door lock switches are disabled. However, if the driver's
door is not open, the master door
lock switches are not disabled. Pushing the switch down on the
open passenger's door will lock all
doors. If you try to lock an open
driver's door by pushing in the lock
tab, the tabs on all doors pop out. Pushing in the lock tab on the
passenger's door only locks that door. Remote Transmitter
You can lock and unlock your car with the remote transmitter. When
you push the LOCK button, all doorslock. You will hear a beep, and the
parking lights, taillights and license
plate lights will flash once. When you push the UNLOCK button
once, only the driver's door unlocks.
The remaining doors unlock when you push the button a second time.
You will hear two beeps, and the outside lights will flash twice, each
time you push the button.
The ceiling lights (if the ceiling light switch is in the center position) and
the door courtesy lights will come on
when you press the UNLOCK button. If you do not open any door, the
lights stay on for about 10 seconds,
then fade out. If you relock the doors with the remote transmitter before 10 seconds have elapsed, the lights
will go off immediately.

Instruments and Controls
LED

UNLOCK
BUTTON
LOCK

BUTTON

TRUNK
RELEASE

BUTTON

PANIC
BUTTON

Keys and Locks

If you unlock the doors with the
remote transmitter, but do not open any of the doors within 30 seconds,
the doors automatically relock and
the security system sets.
You cannot lock any of the doors
with the remote transmitter if any door is not fully closed or the key is
in the ignition switch. You cannot
unlock any of the doors with the key
in the ignition switch.
To open the trunk, push the Trunk Release button for approximately
one second.
You can open the trunk with the remote transmitter regardless of the
position of the main switch in the
glove box. The trunk will not open if
the key is in the ignition switch. Turning the Beep Off and On
You can program the keyless entry system so it does not beep when you
lock and unlock the doors. This
procedure only turns off the beep;
the exterior lights will still flash.
To turn this feature off, stand near the car with the remote transmitter.Press and hold the Trunk Release
button, then press the Lock button
within one second. You should see
the LED on the remote transmitter come on for one second. Release the
buttons after the LED goes out.
To turn this feature on, repeat the above procedure. You should see the
LED blink twice.
After you program the remote transmitter, make sure the trunk lidis closed. Panic Mode
Panic mode allows you to remotely
activate your car's security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will flash, for about 30 seconds.
To activate panic mode, press and hold the PANIC button for about two
seconds.

To cancel Panic mode before 30 seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)

position.

CONTINUED

Instruments and Controls

Seat Adjustments

See pages 12 — 14 for important safety
information and warnings about how to
properly position seats and seat-backs.
Make all seat adjustments before
you start driving.
Your Acura has power adjustments for both front seats. The two power seat adjustment switches are on the
outside edge of the seat bottom.
You can adjust the power seats with the ignition switch in any position. Driver's Seat Adjustments
The long horizontal switch adjusts the seat bottom in several directions.
The short vertical switch adjusts the seat-back angle.
Push the horizontal switch forward
or backward to move the seat
forward or backward. Pull up or push down on the front of
the switch to move the seat bottom's
front edge up or down. Pull up or
push down on the rear of the switch
to move the rear of the seat bottom up or down.

Instruments and Controls

Mirrors

Keep the inside and outside mirrors
clean and adjusted for best visibility.
Be sure to adjust the mirrors before
you start driving.
The inside mirror has an automaticanti-glare mechanism. When the
AUTO switch is pushed in, the indicator will light. When the mirrorsenses light from the headlights of
the car behind you, the mirror surface will automatically darken to
reduce the glare. Adjusting the Power Mirrors
Adjust the outside mirrors with the adjustment button on the driver's
door armrest:
1. Turn the ignition switch ON (II).
2. Move the selector switch to L (driver's side) or R (passenger's

side).

CONTINUED

Instruments and Controls

INDICATOR
SENSOR
AUTO SWITCH SELECTOR SWITCH

Mirrors

ADJUSTMENT BUTTON

3. Move the mirror right, left, up or
down by pushing the adjustment

button in that direction.
4. When you finish, move the
selector switch to the center (off)
position. This turns off the adjustment button so you can't
move a mirror out of position by accidentally bumping the button.
Outside mirror positions can be
stored in the driving position
memory system (see page 101).
HEATED MIRROR BUTTON

The outside mirrors are heated to re- move fog and frost. With the ignitionswitch ON (II), turn on the heaters
by pressing the button. The light in the button comes on as a reminder.
Press the button again to turn the
heaters off.
Instruments and Controls