battery Acura RL 2004 3.5 User Guide

µµ
The SCAN f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button. The
system plays each channel in
numerical order f or a f ew seconds,
then selects the next channel. When
you hear a channel you want to
continue listening to, press the
button again. Pick the preset button you want
f or that channel. Press and hold
the button until you hear a beep.
Repeat steps 2 to 3 to store the
f irst six channels.
Youcanstoreupto12
preset channels using the six preset
buttons. Each button stores one
channel f rom the XM1 band and one
channel f rom the XM2 band. To store a channel:
To store a channel: Press the SAT Radio button until
XM1 or XM2 appears in the
display.
Once a channel is stored, simply
press and release the proper preset
button to tune to it.Press the SAT Radio button again.
The available XM band will show.
Store the next six channels using
steps 2 through 3.
The presets will be lost if your car’s
battery goes dead, is disconnected,
or the radio f use is removed.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected. Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
1.
2. 3.
4.
5.
CONT INUED
Audio System
Comf ort and Convenience Feat ures
SCAN
Preset
175

You will have to store your favorite
stations in the Preset buttons after
the system begins working. Your
original settings were lost when
power was disconnected.
Your car’s audio system will disable
itself if it is disconnected f rom
electrical power f or any reason. To
make it work again, the user must
enter a specif ic f ive-digit code in the
Preset buttons. Because there are
hundreds of number combinations
possible f rom f ive digits, making the
system work without knowing the
exact code is nearly impossible.
Youshouldhavereceivedacardthat
lists your audio system’s code
number and serial number. It is best
tostorethiscardinasafeplaceat
home. In addition, you should write
the audio system’s serial number in
this Owner’s Manual. If you should
happen to lose the card, you must
obtain the code number f rom your
Acura dealer. To do this, you will
need the system’s serial number. If you make a mistake entering the
code, do not start over or try to
correct your mistake. Complete the
f ive-digit sequence, then enter the
correct code. You have three tries to
enter the correct code. If you are
unsuccessful in three attempts, you
must then leave the system on for
one hour bef ore trying again. If your car’s battery is disconnected
or goes dead, or the radio f use is
removed, the audio system will
disable itself . If this happens, you
will see ‘‘ ’’ in the f requency
display the next time you turn on the
system. Use the Preset buttons to
enter the f ive-digit code. If it is
entered correctly, the radio will start
playing.
Thef t Protection
Audio System
Comf ort and Convenience Feat ures180

The HomeLinkUniversal
Transceiver built into your car can
be programmed to operate remotely-
controlled devices around your home,
such as garage doors, lighting, or
home security systems. It can
replaceuptothreeremote
transmitters. Always ref er to the operating
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with the HomeLink
Universal Transceiver. If you do not
have this inf ormation, you should
contact the manuf acturer of the
equipment.
While training or using HomeLink,
make sure you have a clear view of
the garage door or gate, and that no
one will be injured by its movement.If you are training HomeLink to
operate a garage door or gate, it is
recommended that you unplug the
motor f or that device during
training. Repeatedly pressing the
remote control button could burn
out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your car’s battery goes dead or is
disconnected.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program
HomeLink to operate it. Garage door
openers manuf actured bef ore that
date do not have a safety feature that
causes them to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury. If you
have questions, call (800) 355-3515.
If you have problems with training
the HomeLink Universal Transceiver,
or would like inf ormation on home
products that can be operated by the
transmitter, call (800) 355-3515. On
the Internet, go to www.homelink.
com.
HomeLink
is a registered
trademark of Johnson Controls .TM
Important Saf ety Precautions General Inf ormation
Customer Assistance
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures186

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
OnStar uses the Global Positioning
System (GPS) to locate your car f or
f unctions such as route guidance and
roadside assistance. GPS is af f ected
by structures that can obstruct the
signal, such as tunnels, parking
structures, and tall buildings. It may
not be possible f or OnStar to
pinpoint your location if you are in or
near such structures.
OnStar uses cellular technology to
communicate with your car. Cellular
coverage varies by location, which
may af f ect the ability to establish a
connection, or the quality of the
connection. When you turn of f your car’s ignition,
the OnStar system goes into low-
power mode. Af ter 48 hours, it
switches to sleep mode to conserve
your car’s battery power. Features
such as remote door unlocking and
misplaced vehicle assistance will not
work af ter your car has been parked
formorethat48hours.
OnStar
is a registered trademark of
the OnStar Corporation.
System Limitations
OnSt ar
Comf ort and Convenience Feat ures201

Push the accelerator pedal half-
way to the f loor and hold it there
while starting the engine. Do not
hold the ignition key in START
(III) f or more than 15 seconds.
When the engine starts, release
the accelerator pedal gradually as
the engine speeds up and smooths
out.
If the engine fails to start in step 2,
push the accelerator pedal to the
f loor and hold it there while you
try to start the engine for no more
than 15 seconds. If the engine
does not start, return to step 2.
If the engine still does not start,
press the accelerator pedal all the
way down and hold it there while
starting in order to clear f looding.
As bef ore, keep the ignition key in
the START (III) position f or no
more than 15 seconds. Return to
step 5 if the engine does not start.
If it starts, lif t your f oot of f the
accelerator pedal so the engine
does not race.
An engine is harder to start in cold
weather. The thinner air f ound at
high altitude above 8,000 f eet
(2,400 meters) adds to the problem.
Use the f ollowing procedure: Turn of f all electrical accessories
to reduce the drain on the battery.
Apply the parking brake.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.
Make sure the shif t lever is in
Park. Press on the brake pedal.
Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. If the engine
does not start right away, do not
hold the key in START (III) f or
more than 15 seconds at a time.
Pause f or at least 10 seconds
bef ore trying again.
If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed half-way
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.
1.
2.
3.
4.
5.
6.
1.2.
3.
Starting in Cold Weather at High
A ltitude (A bove 8,000 f eet/
2,400 meters)
Driving
Starting the Engine
217

If you have the skills and tools to per-
f orm more complex maintenance
tasks on your Acura, you may want
to purchase the Service Manual. See
page f or inf ormation on how to
obtain a copy, or see your Acura
dealer. This section also includes
Maintenance Schedules f or normal
driving and severe driving conditions,
a Maintenance Record, and instruc-
tions f or simple maintenance tasks
you may want to take care of
yourself . This section explains why it is
important to keep your car well
maintained and how to f ollow basic
maintenance saf ety precautions.......................
Maintenance Saf ety .240
.
Important Safety Precautions . 241
.................
Maintenance Schedule . 242
...
Required Maintenance Record . 249
.......
Owner Maintenance Checks . 251
..............................
Fluid Locations .252
......................................
Engine Oil .253
..................................
Adding Oil .253
....................
Recommended Oil .253
..............................
Synthetic Oil .254
....................................
Additives .254
.....
Changing the Oil and Filter . 255
.............................
Cooling System .257
............
Adding Engine Coolant . 257
.......
Replacing Engine Coolant . 259
....................
Windshield Washers .263
....
Automatic Transmission Fluid . 264
..............................
Dif f erential Oil .265
....................................
Brake Fluid .266
............................
Brake System .266
..............................
Power Steering .266
....................................
Hood Latch .267
.....................
Air Cleaner Element .267
....................................
Spark Plugs .269
..............................
Replacement .269
............................
Specif ications .272 ...........................................
Battery .272
.................................
Wiper Blades .275
..............
Air Conditioning System . 277
..................
Dust and Pollen Filter . 278
.....................................
Drive Belts .278
....................................
Timing Belt .279
...............................................
Tires .279
......................................
Inf lation .279
..................................
Inspection .281
..............................
Maintenance .282
.............................
Tire Rotation .282
...
Replacing Tires and Wheels . 283
......................
Wheels and Tires .284
..........................
Winter Driving .284
.............................
Snow Tires .285
............................
Tire Chains .285
.............................................
Lights .286
........................
Replacing Bulbs .288
...........................
Storing Your Car .297
355
Maintenance
Maint enance239

Be sure
there is adequate ventilation
whenever you operate the engine.
Let the
engine and exhaust system cool
bef ore touching any parts.
Do
not run the engine unless in-
structed to do so. Read the instructions before you
begin, and make sure you have the
tools and skills required.
To reduce the possibility of f ire or
explosion, be caref ul when working
around gasoline or batteries. Use a
commercially available degreaser or
parts cleaner, not gasoline, to clean
parts. Keep cigarettes, sparks, and
flames away from the battery and all
f uel-related parts.
Bef ore you begin any maintenance,
make sure your car is parked on
level ground and that the parking
brake is set. Also, be sure the engine
is of f . This will help to eliminate
several potential hazards:
You should wear eye protection and
protective clothing when working
near the battery or when using
compressed air.
Maintenance Saf ety
Maint enance
Important Saf ety Precautions
Carbon monoxide poisoning
f rom engine exhaust.
Burns f rom hot parts.
Injury f rom moving parts.
241

´
µSpark Plug Gap:Check the battery condition by
looking at the test indicator window
on the battery. The label on the
battery explains the test indicator’s
colors.
Check the condition of your car’s
battery monthly. You should check
the color of the test indicator window,
and f or corrosion on the terminals.
NGK:
DENSO: Battery
Specif ications:
Spark Plugs, Battery
Maint enance272
TEST INDICATOR WINDOW
0.04 in (1.1 mm) PFR5L-11
PK16PR-L110
0.1 mm

µ
Check the battery terminals for
corrosion (a white or yellowish
powder). To remove it, cover the
terminals with a solution of baking
soda and water. It will bubble up and
turn brown. When this stops, wash it
of f with plain water. Dry of f the
battery with a cloth or paper towel.
Coat the terminals with grease to
help prevent f uture corrosion.
If the terminals are severely cor-
roded, clean them with baking soda
and water. Then use a wrench to
loosen and remove the cables f rom
the terminals. Always disconnect the
negative ( ) cable f irst and recon-
nect it last. Clean the battery termi-
nals with a terminal cleaning tool or
wire brush. Reconnect and tighten
the cables, then coat the terminals
with grease.
Battery posts,
terminals, and related accessories
contain lead and lead compounds. If you need to connect the battery to
a charger, disconnect both cables to
prevent damage to the vehicle’s
electrical system.
CONT INUED
Battery
Maint enance
WARNING:
Wash hands af ter handling.
273
The battery gives off explosive
hydrogen gas during normal
operation.
A spark or flame can cause the
battery to explode with enough
force to kill or seriously hurt you.
Wear protective clothing and a
face shield, or have a skilled
mechanic do the battery
maintenance.

Make sure the climate control sys-
tem is off.
Start the engine and let it run until
it warms up (the radiator cooling
fan comes on at least twice), and
let it idle f or f ive more minutes.
If your car’s battery is disconnected
or goes dead, the engine’s computer
needs to ‘‘relearn’’ the idle control.
Af ter replacing or recharging the
battery:
Your driver’s power window (see
page ) and your audio system
will also disable itself when the bat-
tery is disconnected or goes dead.
Thenexttimeyouturnontheradio
you will see ‘‘ ’’ in the f requency
display. Use the Preset buttons to en-
ter the f ive-digit code (see page ).If your car’s battery is disconnected
or goes dead, all stored driving
positions will be lost. To store the
driving positions again, see the
storingprocedureonpage .
The Navigation System will also
disableitself.Thenexttimeyouturn
on the ignition switch, the system
will require you to enter a PIN
bef ore it can be used. Ref er to the
Navigation System Owner’s Manual.
1.
2. 103
98
180On cars with Navigation System
Battery
Maint enance274
Charging the battery with the cables
connected can seriously damage your
car’s electronic controls. Detach the
battery cables bef ore connecting the
battery to a charger.