lock Acura RL 2004 3.5 Owner's Guide

To change between low beams and
high beams, pull the turn signal lever
until you hear a click, then let go.
The blue high beam indicator will
light (see page ).
When the light switch is in either of
these positions, the Lights On
indicator comes on as a reminder.
This light remains on if you leave the
light switch on and turn the ignition
switch to ACCESSORY (I) or LOCK
(0). If you leave the lights on with the
ignition switch in ACCESSORY (I)
or LOCK (0), you will hear a
reminder chime when you open the
driver’s door.
The rotating switch on the lef t lever
controls the lights. Turning this
switch to the position turns on
the parking lights, taillights,
instrument panel lights, side marker
lights, and rear license plate lights.
Turning the switch to the position turns on the
headlights. 62
U.S. models only
Headlights
Controls Near the Steering Wheel
Inst rument s and Cont rols68

Adjust the wiper arms to the winter
position by grasping either arm near
the pivot. Pull on the arm, parallel to
the windshield, until it locks in the
higher position. Push the arm in the
other direction to return the wipers
to the summer position.
To operate the wipers in mist mode,
push the control lever down. The
wipers run at high speed until you
release the lever. This gives you a
quick way to clear the windshield. The windshield wiper arms have two
parked positions: Winter and
Summer. In the winter position, the
arms sit slightly above the edge of
the hood. This reduces the possibili-
ty of damage to the wiper arms or
windshield wiper motor by a build-up
of snow and ice.
A heavy build-up of snow or ice on
the wiper arms will cause them to
automatically park in the winter
position.
Wiper A rms Wint er Posit ion
Controls Near the Steering Wheel
Inst rument s and Cont rols74
WIPER ARMS

Your car comes with two master
keys and a valet key.Donotdropthekeysorsetheavy
objects on them.
These keys contain electronic
circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the
circuits are damaged.
Protect the keys f rom direct
sunlight, high temperature, and
high humidity.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
The keys do not contain batteries.
Do not try to take them apart.
The master key fits all the locks on
your car:
 Ignition
 Doors
 Trunk
 Trunk pass-through cover
Glovebox The valet key works only in the
ignition and the door locks. You can
keep the trunk, trunk pass-through
cover, and glove box locked when
you leave your car and the valet key
at a parking f acility.
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Keep
the tag stored in a safe place. If youneed to replace a key, use only an
Acura-approved key blank.
CONT INUED
Keys
Keys and Locks
Inst rument s and Cont rols79
MASTER
KEYS
(Black)
VALET
KEY
(Gray)
KEY
NUMBER
TAG

Your car also comes with two remote
transmitters; see page for an
explanation of the operation.
Youshouldalsoreceiveasmallcase
containing a learning key. It is used
by the Acura dealer to code replace-
ment keys to your car’s Immobilizer
System. It must not be used in your
car’s ignition switch. Store the learn-
ing key with the key number plate in
a safe place.If you attempt to use the learning
key to start your car’s engine, it may
cause a malfunction in the system
that makes your master and valet
keys unusable. If this happens, you
should contact your Acura dealer.
If you need a new key made, take the
key number plate, the learning key,
and all other keys that came with
your car to your Acura dealer.The Immobilizer System protects
your car f rom thef t. A properly-
coded master or valet key must be
used in the ignition switch f or the
engine to start. If an improperly-
coded key (or other device) is used,
the engine’s f uel system is disabled.
When you turn the ignition switch to
ON (II), the Immobilizer System
indicator should come on f or a f ew
seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to
LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again.
84
Remote Transmitter
L earning K eyImmobilizer System
Inst rument s and Cont rols
Keys and Locks
80

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.The system may not recognize your
key’s coding if another immobilizer
key or other metal object is near the
ignition switch when you insert the
key. To make sure the system
recognizes the key code: If you have lost your key and you
cannot start the engine, contact your
Acura dealer. Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your car undriveable.
Do not keep other immobilizer
keys on the same key ring.
Use a plastic or leather key f ob,
not metal.
Keep other keys away f rom your
car’s key and the ignition switch
while trying to start the engine.
If the system repeatedly does not
recognize the coding of your key,
contact your Acura dealer.
The Immobilizer System indicator
will also blink several times when
you turn the ignition switch f rom ON
(II) to ACCESSORY (I) or LOCK (0).
Keys and Locks
Inst rument s and Cont rols81

µ
µ
µ
µ
The ignition switch is on the right
side of the steering column. It has
f our positions:
LOCK(0)
 ACCESSORY (I)
 ON (II)
 START (III) If the f ront wheels are turned, the
anti-thef t lock may sometimes make
it difficult to turn the key from
LOCK to ACCESSORY. Firmly turn
the steering wheel to the lef t or to
the right as you turn the key.
In this position,
you can operate the audio system
and the cigarette lighter. You can insert or
remove the key only in this position.
To switch f rom ACCESSORY to
LOCK, you must push the key in
slightly as you turn it. The shif t lever
must also be in Park. The anti-thef t
lock will lock the steering column
when you remove the key. Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key.
The engine will not start if the
Immobilizer System does not
recognize the key’s coding (see page ).
You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn of f the beeper.
This is the normal key
position when driving. All f eatures
and accessories on the vehicle are
usable. Several of the lights on the
instrument panel come on as a test
when you turn the ignition switch f rom ACCESSORY to ON.
80
Ignition Switch
A CCESSORY (I) LOCK (0)ST A RT (III)
ON (II)
Keys and Locks
Inst rument s and Cont rols82

Each f ront door has a master door
lock switch. Either switch locks and
unlocks all doors. Push the switch
down to lock all doors, and up to
unlock them.Each door has a lock tab at the top of
the door. When you push down the
lock tab on the driver’s door, all
doors lock. Pulling up the lock tab on
the driver’s door only unlocks that
door.Thelocktaboneach
passenger’s door only locks and
unlocks that door.To lock any passenger’s door when
getting out of the vehicle, push the
lock tab down and close the door. To
lock the driver’s door, remove the
key f rom the ignition switch and
push the lock tab down or push the
master switch down, then close the
door.
All doors can be locked f rom the
outsidebyusingthekeyineither
f ront door. To unlock only the driver’s
door f rom the outside, insert the key
in the driver’s door lock, turn the key
and release it. If you turn the key
and hold it, all doors will unlock. All
f our doors will unlock when you
unlock the passenger’s door with the
key.
CONT INUED
Power Door L ocks
Keys and Locks
Inst rument s and Cont rols83
MASTER DOOR LOCK SWITCH
LOCK TAB

If you f orget and leave the key in the
ignition switch, Lockout Prevention
will not allow you to lock the driver’s
door. With the driver’s door open
andthekeyintheignition,both
master door lock switches are
disabled. However, if the driver’s
door is not open, the master door
lock switches are not disabled.
Pushing the switch down on the
open passenger’s door will lock all
doors. If you try to lock an open
driver’s door by pushing in the lock
tab, the tabs on all doors pop out.
Pushinginthelocktabonthe
passenger’s door only locks that door.The ceiling lights (if the ceiling light
switch is in the center position) and
the door courtesy lights will come on
when you press the UNLOCK button.
If you do not open any door, the
lights stay on f or about 10 seconds,
then f ade out. If you relock the doors
with the remote transmitter before
10 seconds have elapsed, the lights
will go of f immediately.
You can lock and unlock your car
with the remote transmitter. When
you push the LOCK button, all doors
lock. You will hear a beep, and the
parking lights, taillights and license
plate lights will f lash once. When you push the UNLOCK button
once, only the driver’s door unlocks.
The remaining doors unlock when
you push the button a second time.
You will hear two beeps, and the
outside lights will f lash twice, each
time you push the button.
Remote Transmitter
L ockout Prevent ion
Keys and Locks
Inst rument s and Cont rols84
LOCK
BUTTON
LED
UNLOCK
BUTTON TRUNK
RELEASE
BUTTON
PANIC
BUTTON

If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock and
the security system sets.
You cannot lock any of the doors
with the remote transmitter if any
door is not f ully closed or the key is
in the ignition switch. You cannot
unlock any of the doors with the key
in the ignition switch.
To open the trunk, push the Trunk
Release button f or approximately
one second.
You can open the trunk with the
remote transmitter regardless of the
position of the main switch in the
glove box. The trunk will not open if
the key is in the ignition switch.You can program the keyless entry
system so it does not beep when you
lock and unlock the doors. This
procedure only turns of f the beep;
the exterior lights will still f lash.
Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
To turn this feature off, stand near
the vehicle with the remote
transmitter. Press and hold the
Trunk Release button, then press the
Lock button within one second. You
should see the LED on the remote
transmitter come on f or one second.
Release the buttons after the LED
goes out.
To turn this feature on, repeat the
above procedure. You should see the
LED blink twice.
Af ter you program the remote
transmitter, make sure the trunk lid
is closed.
CONT INUED
T urning t he Beep Of f and On
Panic Mode
Keys and Locks
Inst rument s and Cont rols85

µ
To replace the battery, place a cloth
on the edge of the transmitter and
remove the upper half by carefully
prying on the edge with a small f lat-
tip screwdriver. Snapthetwohalvesof the
transmitter case back together.
When the remote transmitter’s
battery begins to get weak, it may
take several pushes on the button to
lock or unlock the doors, and the
LED will get dim. Replace the
battery as soon as possible.
Battery type: CR2025 Remove the old battery and note the
polarity. Make sure the polarity of
the new battery is the same ( side
f acing up), then insert it in the
transmitter.
Replacing the Battery
Inst rument s and Cont rols
Keys and Locks
86