Acura RL 2006 Owner's Manual

ÛÝÛ
Ý
ÛÝ
ÛÝ
There are two position setups you
can make:MEMORY POSITION LINK
AUTO TILT & TELESCOPIC
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select POSITION SETUP by
pressing the INFO ( / ) button,
and then press the SEL/RESET
button.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
Position Setup
100
Press the or button.
Press the SEL/RESET button. seepage101
seepage103

ÛÝ
When Memory Position Link is set
to ON, the driver’s seat, the steering
wheel, and the outside mirror
positions move to the positions
stored in memory. To cause the
memory to activate, open the driver’s
door with the remote, or grab the
door handle while carrying the
remote.
To set the seat memory position, see
page . For inf ormation on using
the remote, see page .
While the multi-information display
is in the POSITION SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
166
156
CONT INUED
Multi-Inf ormation Display
Memory Posit ion L ink
Inst rument s and Cont rols
101

ÛÝ
To exit MEMORY POSITION LINK
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the
memory position link setup.
Multi-Inf ormation Display
102

ÛÝÛÝ
When AUTO TILT TELESCOPIC is
set to ON, the steering wheel
automatically moves f ully in and up
when you turn the ignition switch to
the LOCK (0) position and release it,
or when you remove the built-in key
from the ignition switch.
While the multi-information display
is in the POSITION SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
CONT INUED
Multi-Inf ormation Display
A ut o T ilt & T elescopic
Inst rument s and Cont rols
103

ÛÝ
To exit AUTO TILT &
TELESCOPIC without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the auto
tilt and telescopic setup.
Multi-Inf ormation Display
104

Û
Ý
ÛÝ Û
Ý
ÛÝ
CONT INUED
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. There are three settings in the
keyless access setup:
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select KEYLESS ACCESS
SETUP by pressing the INFO ( / ) button, then press the SEL/
RESET button.
Multi-Inf ormation Display
K EYL ESS A CCESS Setup
Inst rument s and Cont rols
105
Press the or button.
Press the SEL/RESET button. seepage106
seepage108
seepage110

ÛÝ
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select DRIVER DOOR ONLY or
ALL DOORS by pressing the INFO
( / ) button, then press the SEL/
RESET button to enter your
selection.
Multi-Inf ormation Display
Door Unlock Mode
106

ÛÝ
To exit DOOR UNLOCK MODE
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the door
unlock mode setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
107

ÛÝÛÝ
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some exterior
lights blink twice when you unlock
thedoorsbygrabbingthedriver’s
door handle while carrying the
remote.
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.
The same exterior lights blink once
when you lock the doors by touching
the door lock sensor while carrying
the remote.
Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
Multi-Inf ormation Display
K eyless A ccess L ight Flash
108

ÛÝ
To exit KEYLESS ACCESS LIGHT
FLASH without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the
keyless access light f lash setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109