steering wheel Acura RL 2007 Owner's Guide

To select a memorized position, do
this: Press
the desired memory button
(1 or 2) until you hear a beep.
The system will move the seat,
steering wheel, and outside mirrors
to the memorized positions. The
indicator in the selected memory
button will flash during movement.
When the adjustments are complete,
you will hear two beeps, and the
indicator will remain on.
Make sure the shift lever is in
Park. To change the ‘‘MEMORY
POSITION LINK’’ setting, see page
.
To cancel the storing procedure
after pressing the MEMO button:
Do not press a memory button
within 5 seconds.
Readjust the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected. Readjust the seat or steering
position.
1. 2.
104
CONT INUED
Selecting a Memorized Position
Driving Position Memory System
Inst rument s and Cont rols
161
MEMORY BUTTONS
——
y
y
(y
y

Press any button on the control
panel: MEMO, 1, or 2.
Adjust the outside mirrors. Shif t out of Park. Push any of the adjustment
switches f or the seat or steering
wheel.
If you select a memorized position
without pushing the ignition switch
knob or inserting the built-in key in
the ignition switch, only the seat and
outside mirrors will adjust. To get
the system to also adjust the steering
wheel, push and turn the ignition
switch or insert the built-in key in
the ignition switch. You will hear two
beeps when it is complete. You can use the adjustment switches
to change the positions of the seat,
steering wheel, or outside mirrors
af ter they are in their memorized
position. If you change the
memorized position, the indicator in
the memory button will go out. To
keep this driving position f or later
use, you must store it in the driving
position memory.
To stop the system’s automatic
adjustment, do any of the f ollowing:
Driving Position Memory System
162
——
y


y
(y
y

When you push the ignition switch,
theremoteandthevehiclerecognize
each other. After the recognition,
the remote indicator flashes, and a
beeper sounds once. After the beep,
turn the ignition switch.
When the remote is out of the
operating range, the ignition switch
is locked.
If the ignition switch cannot be
turned from the LOCK (0) position
to the ACCESSORY (I) position afterthe
beep, the steering wheel is
locked. To unlock the steering wheel,
turn it right and left while turning
the ignition switch at the same time.
Iftheremoteandthevehicledonot
recognize each other, turn the
ignition switch to the LOCK (0)
position, remove the ignition switch
co ver, insert the built-in key, and
turn the switch (see pages and
). Before leaving the vehicle, make
sure the ignition switch is in the
LOCK (0) position.
You will also see a ‘‘RETURN
IGNITION SWITCH TO LOCK (0)
POSITION’’ message on the multi-
inf ormation display. To turn the ignition switch to the
LOCK (0) position, put the
transmission in Park, press the
switch in, and turn it to the LOCK
(0) position. When the transmission
is not in Park, you cannot turn the
ignition switch to the LOCK (0)
position.
If you open the driver’s door with the
ignition switch in the ACCESSORY
(I) position, a beeper will sound.
151
174
CONT INUED
Ignition Switch
K eyless A ccess System
Inst rument s and Cont rols
173
——
y

y
(y
y

ÛÝ´
µ ´µ ´
µ
´µ
Three controls f or the audio system
are mounted in the steering wheel
hub. These let you control basic
f unctions without removing your
hand f rom the wheel.
The VOL button adjusts the volume
up ( ) or down ( ). Press the top
or bottom of the button, hold it until
the desired volume is reached, then
release it. The MODE button changes the
mode. Pressing the button
repeatedly selects FM1, FM2, AM,
XM Satellite Radio (U.S. models
except Hawaiian), or a disc (if a disc
is loaded).
If you are listening to the radio, use
the CH button to change stations.
Each time you press the top ( ) of
the button, the system goes to the
next preset station on the band you
are listening to. Press the bottom
( ) to go back to the previous
station.
To activate the seek function, press
and hold the top ( ) or bottom ( )
of the CH button until you hear a
beep. The system searches up or
down f rom the current f requency to
find a station with a strong signal.
If you are playing a disc, the system
skips to the beginning of the next
track/file (in MP3/WMA mode)
each time you press the top ( ) of
the CH button. Press the bottom
( ) to return to the beginning of the
current track/file. Press it again to
return to the previous track/f ile.
To select a dif f erent disc (f older in
MP3/WMA mode), press and hold
the top ( ) or bottom ( ) of the
CH button until you hear a beep.
CONT INUED
Remote Audio Controls
Features
237
MODE
BUTTON
CH
BUTTON
VOL
BUTTON
——
y
y
(yy

This button activates the voice
control system. Press it when you
want to give a voice command. See
on page for
a list of voice commands.
This button has the same function as
the CANCEL button on the center
console(seepage ).Whenyou
press it, the display returns to the
previous screen. When the previous
screen appears, the system replays
the last prompt. This button can be
used to cancel an audio, climate
control, or compass system voice
command up to one second af ter the
command conf irmation.
For models with navigation
system, ref er to the navigation
system manual.
Your vehicle has a voice control
system that allows hands-f ree
operation of the audio system, the
climate control system and some
functionsof thecompasssystem.
The voice control system uses the
TALK and BACK buttons on the
steering wheel and a microphone near the map light on the ceiling.
While using the voice control
system, all of the speakers are
muted. 241
266
Voice Command Index
Voice Control BasicsTalk Button
Back But t on
Compass System (U.S. model without navigation system)
Features
263
NOTE: NOTE:
TALK BUTTON
BACK BUTTON MICROPHONE
(on the ceiling)
——
y

y
(yy

Cruise control allows you to maintain
asetspeedabove25mph(40km/h)
without keeping your foot on the
accelerator pedal. It should be used
for cruising on straight, open
highways. It is not recommended for
city driving, winding roads, slippery
roads, heavy rain, or bad weather.
Push in the CRUISE button or the
ACC button (models with adaptive
cruise control) on the steering
wheel. The CRUISE MAIN or
green ACC indicator (models with
ACC) indicator on the instrument
panel comes on.
To switch from ACC to cruise
control, press the distance button on the steering wheel, and hold it
f or 1 second (see page ).
Accelerate to the desired cruising
speedabove25mph(40km/h).
Press and release the SET/
DECELbuttononthesteering
wheel. The CRUISE CONTROL
icon appears on the multi-
inf ormation display to show the
system is now activated.
When cruise control is on while
driving, the SH-AWD torque
distribution monitor and the tire
pressure monitor are not shown
on the multi-information display.
1. 2.
3.
292
CONT INUED
On models with adaptive cruise
control
Using Cruise Control
Cruise Control
Features
275
RES/
ACCEL
BUTTON
CRUISE (ACC) BUTTON
SET/
DECEL
BUTTON
Non-ACC model is shown
Improper use of the cruise
control can lead to a crash.
Use the cruise control only
when traveling on open
highways in good weather.
——
y
y
(yy

Tap the brake pedal.
Push the CANCEL button on the
steering wheel.
Resting your f oot on the brake pedal
causes cruise control to cancel. Even with cruise control on, you can
still use the accelerator pedal to
speed up f or passing. Af ter
completing the pass, take your foot
of f the accelerator pedal. The vehicle
will return to the set cruising speed.
You can cancel cruise control in any
of these ways:Push the CRUISE (ACC) button. When you push the CANCEL button
or tap the brake pedal, the system
remembers the previously set speed.
To return to that speed, accelerate to
above25mph(40km/h),thenpress
and release the RES/ACCEL button.
The CRUISE CONTROL (ACC
(green)) indicator comes on. The
vehicle accelerates to the same
speed as bef ore.
Pressing the CRUISE (ACC) button
turns the system completely of f and
erases the previous cruising speed. Resuming the Set Speed
Canceling Cruise Control
Cruise Control
Features
277
CANCEL BUTTON
CRUISE (ACC) BUTTON
Non-ACC model is shown
——
y
y
(yy

The radar sensor for ACC is shared
with the collision mitigation brake
system (CMBS). For more
information on the radar sensor, see
page . For more information on
CMBS, see page .
Adaptive cruise control (ACC)
consists of a radar sensor in the
f ront grille, the ACC buttons on the
steering wheel, and the ACC
f unctions of the multi-inf ormation
display.
355
356
If equipped
A CC Components
A daptive Cruise Control (A CC)
278
ACC INDICATOR
MULTI-INFORMATION
DISPLAY
RES/ACCEL
BUTTON
ACC BUTTON
DISTANCE BUTTON
CANCEL BUTTON SET/DECEL
BUTTON
——
y

y
(yy

ACC does not work below 25 mph
(40 km/h). It cannot bring your
vehicle to a complete stop.
ACC will not sound a beeper or
display a message on the multi-
inf ormation display to warn you of
vehicles going slower than 13 mph
(20 km/h) or vehicles that are
parked. In these cases, it is up to
you to maintain a safe distance by
using the brake pedal.
ACC may not recognize
motorcycles or other small
vehicles ahead of your vehicle.ACC may react to vehicles beside
you or even building beside you by
momentarily applying the brakes
or sounding a beeper under
conditions such as a sudden curve
or narrowing of the road, an
abrupt movement of the steering
wheel, or if you are in an unusual
position within your lane.
Limitations
A daptive Cruise Control (A CC)
282
——
y
y
(yy

Push the ACC button on the
steering wheel. The ACC indicator
on the instrument panel comes on,
and ‘‘ACC’’ is shown on the multi-
inf ormation display.
Accelerate to the desired speed
above25mph(40km/h).Press and release the SET/
DECELbuttononthesteering
wheel.
If you press the SET/DECEL button
when the vehicle speed is below 25
mph (40 km/h), you will hear three
beeps. This means ACC is not
activated, and you cannot set your
speed. When your speed reaches 25 mph
(40 km/h), ACC goes into wait mode,
and ‘‘ACC STANDBY’’ is shown on
the multi-information display.
1.
2. 3.
CONT INUED
Using the ACC
A daptive Cruise Control (A CC)
Features
283
ACC BUTTON SET/DECEL BUTTON
——
y
y
(yy