lock ACURA RL 2012 Owners Manual

Remove the left or right side
engine compartment cover (see
page ).
Use a f lat-tip screwdriver to
remove the holding clip f rom the
windshield washer reservoir. (Passenger’s side) Open the hood.
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ).
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Turn on the lights to make sure
the new bulb is working.
Reinstall the engine compartment
side cover. Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Reinstall the windshield washer
reservoir.
(Driver’s side)
Reinstall the battery cover. (Passenger’s side) 1.
2.
3.
4.
5.6.
7.
8.
9. 457
492
10.
Lights
Replacing a Front Parking/Side
Marker Bulb
Maint enance
471
SOCKET
BULB
CLIP
11/07/20 19:02:13 31SJA670_476
ProCarManuals.com

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise. Use a Phillips-head screwdriver to
remove the two undercover bolts,
and remove the holding clip with a
f lat-tip screwdriver.
Caref ully push up the side under
cover into the bumper. Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Thefoglightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustment should
be done by your dealer or another
qualif ied technician.3.
4. 1.
2.
Lights
ReplacingaFogLightBulb
472
CLIP
CONNECTOR BOLTS
BULBHalogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
11/07/20 19:02:22 31SJA670_477
ProCarManuals.com

Carefully pry in the top or bottom
edge of the trim with a small f lat-
tip screwdriver, and pull the trim
straight back. Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Pull the taillight assembly straight
back out of the body. Remove the two mounting bolts
with an 8 mm wrench. Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two undercover bolts
on the side under cover and
tighten them securely. Put the
holding clip back on the side
undercover and push on the center
until it locks (the center is f lush
with the head).
2. 1. 3.
4.
5. 5.
6.
7.
8.
CONT INUED
Replacing a Rear Turn Signal
Light Bulb
Lights
Maint enance
473
MOUNTING NUT
MAINTENANCE LIDTAIL LIGHT TRIMBOLTS
11/07/20 19:02:33 31SJA670_478
ProCarManuals.com

Open the trunk.
Remove the light assembly cover
by pulling its outside edge. Install the new bulb in the socket
bypushingitstraightinthesocket
until it bottoms.
Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.
When reinstalling the taillight
assembly, align and pop the snap
f asteners in place. Tighten the two
mounting bolts and reinstall the
trim in place.
Tighten the mounting nut securely,
and reinstall the maintenance lid. Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.9. 8.
1.
2.
12. 11. 10.
6.
7.Replacing a Back-up L ight Bulb
Lights
474
SOCKETBULBCOVERS
11/07/20 19:02:42 31SJA670_479
ProCarManuals.com

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms. Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Reinstall the socket into the light
assembly. Turn it clockwise to
lock it in place.Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
Testthelightstomakesurethe
new bulb is working.
Reinstall the back-up light cover.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer. This light should be replaced by your
dealer.
3.
4.5.
6.
7.
Lights
Side T urn Signal L ights
Rear License Plate Light Bulbs High-mount Brake L ight
Maint enance
475
BULB
SOCKET
11/07/20 19:02:52 31SJA670_480
ProCarManuals.com

Make sure the rear f loor mats are
properly hooked to the f loor mat
anchors. Your vehicle is equipped
with front passenger’s seat weight
sensors. If the rear passenger’s f loor
mat is on the seat rail of the f ront
passenger’s seat, the sensors will
detect the decreased weight on the
seat, and they may not work properly. The floor mats that came with your
vehicle hook over the f loor mat
anchors. This keeps the f loor mats
f rom sliding f orward (possibly
interf ering with the pedals), or
backwards (making the f ront
passenger’s weight sensors
inef f ective).If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.
If you use non-Acura f loor mats,
make sure they f it properly and that
theycanbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.
To lock or unlock each anchor, turn
the knob.
Floor Mat s
Maint enance
477
DRIVER’S SIDE FLOOR MAT REAR PASSENGER’S FLOOR MAT
Unlock
LockUnlock
Lock
ANCHORSANCHOR
11/07/20 19:03:05 31SJA670_482
ProCarManuals.com

Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Reinstall the blade assembly to the
wiper arm and tighten the two
screws securely. Reinstall the
cover by pushing it in.
Set the wiper arms back on the
windshield. Adjust the windshield
wipers to their previously parked
position.
Remove the blade f rom its holder
by grabbing the tabbed end of the
blade. Pull up f irmly until the tabs
come out of the holder. 4. 5.6.
7.
8.
Wiper Blades
Maint enance
479
BLADE
BLADE
REINFORCEMENT
11/07/20 19:03:19 31SJA670_484
ProCarManuals.com

If your vehicle’s battery is
disconnected or goes dead, all stored
driving positions will be lost. To
store the driving positions again, see
the storing procedure on page .
The navigation system will also
disableitself.Thenexttimeyouturn
on the ignition switch, the system
will require you to enter a PIN
bef ore it can be used. Ref er to the
navigation system manual.If your vehicle’s battery is
disconnected or goes dead, the audio
system may disable itself . The next
timeyouturnontheradioyouwill
see ‘‘ ’’ in the f requency
display. Use the preset buttons to
enter the code (see page ).
If your vehicle’s battery is
disconnected or goes dead, the
power tilt and telescopic steering
wheel system will be disabled. The
system needs to be reset af ter
reconnecting the battery (see page
). The compass system will also disable
itself.Thenexttimeyouturnonthe
ignition switch, the system will
require you to enter a PIN bef ore it
can be used. Enter the f our-digit anti-
theftsecuritycode(seepage ).
You will also need to reset the clock
according to the instruction of
setting the clock (see page ).298
313280
149 164
On vehicles with navigation systemOn vehicles without navigation system
Checking the Battery
Maint enance
491
11/07/20 19:04:48 31SJA670_496
ProCarManuals.com

To reinstall the cover, reinstall the
two holding clips and secure them
bypushingonthecenterof each
f astener head.
Turn the knob of the cover to
LOCK position as shown in the
illustration.
Turn the knob of the battery cover
toUNLOCKasshowninthe
illustration.Remove the holding clips by
pushingonthecenterof each
f astener head. 2.3.
4.
1.
:
:
Removing the Battery Cover
Checking the Battery
492
KNOBCLIPS
Push to reset/install clip Push to remove clip Unlock
Lock
11/07/20 19:04:55 31SJA670_497
ProCarManuals.com

Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f ans cycle on and of f
twice). Pref erably, do this once a
month. If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors.
Fill the f uel tank.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry.
Leave the parking brake off. Put
the transmission in Park.Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the vehicle is being stored
indoors).
Disconnect the battery.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and trunk seals.
Vehicle Storage
Maint enance
493
11/07/20 19:05:05 31SJA670_498
ProCarManuals.com