display ACURA RL 2012 Owners Manual

´
µThe automatic transmission will not
allow you to shif t up or down if :
You downshif t bef ore the engine
speed reaches the highest
threshold of the lower gear.
If you try to do this, the gear
position indicator will f lash the
number of the lower gear several
times, then return to a higher gear.
If the vehicle speed decreases
below the redline of the selected
lowergearwhiletheindicatoris
f lashing, the transmission
downshif ts, and the indicator
displays the selected gear.
You upshif t bef ore the engine
speed reaches the lowest
threshold of the higher gear. The transmission also shif ts
automatically as the vehicle comes to
a complete stop. It downshif ts to f irst
gear when the vehicle speed reaches
6mph(10km/h)orless. Downshifting with the paddle shifter
allows you to increase the engine
braking when going down steep or
long hills, and provides more power
when climbing uphills. You can
upshif t the transmission manually to
reduce the rpm. When you are driving, the
transmission downshifts to the lower
gear under the f ollowing conditions:
The vehicle slows down to a
certain speed.
You press the brake pedal.
The vehicle detects that you are
driving uphill or downhill. To upshif t, pull the (right) paddle
shif ter. To downshif t, pull the
(lef t) paddle shif ter.
When you accelerate f rom a stop,
the transmission starts in f irst gear,
and shif ts f rom f irst to second
automatically. You must manually
upshif t between second and sixth
gears. Make sure you upshif t bef ore
the engine speed reaches the
tachometer’s red zone.
The transmission remains in the
selectedgear(6,5,4,3,or2).There
is no automatic downshif t when you
push the accelerator pedal to the
f loor.
Driving with the Paddle Shif ters
410
11/07/20 18:54:15 31SJA670_415
ProCarManuals.com

´Drive in the highest gear that lets
the engine run and accelerate
smoothly. This will give you good
f uel economy and ef f ective
emissions control. The f ollowing
shif t points are recommended: When you are in sequential shif t
mode, and the vehicle is stopped,
pull the (right) paddle shifter to
shif t to second gear. You will see
‘‘M2’’ in the display. Starting in
second gear helps to reduce
wheelspin in deep snow or on a
slippery surf ace. You pull both paddle shif ters at
thesametime.
You pull one of the two paddle
shifters with another paddle
shif ter being pressed.
Shif t up
1st to 2nd
2nd to 3rd
3rd to 4th
4th to 5th
5th to 6thNormal acceleration
15 mph (24 km/h)
25 mph (40 km/h)
40 mph (64 km/h)
45 mph (72 km/h)
50 mph (81 km/h)
Driving with the Paddle Shif ters
Recommended Shif t Point s St art ing in Second Gear
Driving
411
11/07/20 18:54:22 31SJA670_416
ProCarManuals.com

µ
µ The super handling-all wheel drive
(SH-AWD) system is a f ull time all-
wheel-drive system that
automatically controls and transf ers
varying amounts of engine torque to
all wheels independently, according
to the driving conditions.
While the SH-AWD system helps to
enhance the vehicle’s driving
stability in all situations, it is still
your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.
The SH-AWD torque distribution
monitor on the multi-inf ormation
display shows you the amount of
torque being sent to the wheels.
Each wheel right f ront (RF), lef t
front(LF),rightrear(RR),andleft
rear (LR) has its own torque
indicator.Each torque indicator is displayed as
a bar graph divided into 5 segments.
The number of segments represents
the amount of torque distributed to
each wheel.
When there is only a slight change in
torque distribution while driving,
such as cruising on level roads at the
same speed, the torque distribution
monitor may stop displaying the
amount of torque. This is not a
system problem. The monitor will
show the amount if the system
senses any change in torque
distribution.
Super Handling-A ll Wheel Drive (SH-A WD)System
SH-AWD T orque Distribution
Monitor
412
TORQUE INDICATOR
TORQUE INDICATOR
TM
11/07/20 18:54:29 31SJA670_417
ProCarManuals.com

If the SH-AWD indicator blinks while
driving, it indicates the dif f erential
temperature is too high. You will also
see an ‘‘SH-AWD DIFF TEMP.
HIGH’’ message on the multi-
inf ormation display. If this happens,
pull to the side of the road when it is
saf e, shif t to Park, and let the engine
idle until the indicator goes out. If
the indicator does not go out, take
your vehicle to a dealer to have it
checked.If the SH-AWD indicator on the
instrument panel stays on, and the
‘‘CHECK SH-AWD SYSTEM’’
message also appears on the multi-
inf ormation display, there is a
problem with the SH-AWD system.
Your vehicle still has normal f ront-
wheel drive with vehicle stability
assist (VSA), but does not have the
advantages of SH-AWD. Have your
vehicle checked by a dealer as soon
as possible.
Super Handling-A ll Wheel Drive (SH-A WD)System
Driving
413
TM
11/07/20 18:54:34 31SJA670_418
ProCarManuals.com

The anti-lock brake system (ABS)
helpspreventthewheelsfrom
locking up, and helps you retain
steering control by pumping the
brakes rapidly, much f aster than a
person can do it.If this indicator comes on, the anti-
lock f unction of the braking system
has shut down. The brakes still work
like a conventional system, but
without anti-lock. You should have
your dealer inspect your vehicle as
soon as possible. You will f eel a pulsation in the brake
pedal when the ABS activates, and
you may hear some noise. This is
normal: it is the ABS rapidly
pumpingthebrakes.Ondry
pavement, you will need to press on
thebrakepedalveryhardbeforethe
ABS activates. However, you may
feel the ABS activate immediately if
you are trying to stop on snow or ice.
Let the ABS work f or you by always
keeping f irm, steady pressure on the
brake pedal. This is sometimes
ref erred to as ‘‘stomp and steer.’’ The electronic brake distribution
(EBD) system, which is part of the
ABS, also balances the f ront-to-rear
braking distribution according to
vehicle loading.When the ABS indicator comes on,
you will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi-
inf ormation display.
If the ABS indicator comes on while
driving, test the brakes as shown on
page .510
You should never pump the brake pedal.
ABS Indicator
Anti-lock Brakes (ABS)
416
11/07/20 18:54:57 31SJA670_421
ProCarManuals.com

The radar sensor is located under
the Acura emblem in the f ront grille.
If the radar sensor cover is covered
with mud, dirt, dead leaves, wet
snow, etc., or if you put a sticker on
it, the CMBS will automatically shut
of f , and the CMBS indicator on the
instrument panel will come on. You
will also see a ‘‘CHECK CMBS
RADAR SENSOR’’ message on the
multi-inf ormation display f or about 5
seconds.There are three bolts on the sides of
the radar sensor. Do not tamper with
these bolts, or you may cause the
system to malf unction. Always keep the radar sensor cover
clean. If it gets dirty, clean it with
water or a mild detergent. Never use
chemical solvents or polishing
powder.
CONT INUED
Radar Sensor
Collision Mitigation Braking System (CMBS )
Driving
419
RADAR SENSOR COVERBOLTS
(Do not tamper)
TM TM
11/07/20 18:55:16 31SJA670_424
ProCarManuals.com

Certain conditions may cause the
radar aim to be temporarily out of
proper range, such as the f ollowing
two examples:
If the radar sensor cover or the radar
sensor ever needs to be removed,
take your vehicle to a dealer. Do not allow anything to impact the
radarsensorortheradarsensor
cover. If either of these parts
receives a strong impact, switch the
system of f by pressing the CMBS
OFF button, and have your vehicle
checked by a dealer. If the f ront
grille ever needs to be repaired,
consult a dealer f irst.
Thetiresarenotcorrectly
maintained. Always make sure the
tire pressures are correct (see
page ), and that the tires are
thecorrectsizeandingood
condition (see Tires on page ). Your vehicle is tilted because of a
heavy load in the rear or from
modif ications to the suspension.
Do not overload your vehicle (see
Carrying Cargo on page ), and
do not make any modif ications to
the suspension (see Accessories
and Modif ications on page ).394
392
482
481
Collision Mitigation Braking System (CMBS )
420
TM TM
When the CMBS is on, the radar sensor
constantly scans f or vehicles directly
ahead of you. This means that driving
on a road with a f ew or no vehicles
could cause a CHECK CMBS RADAR
SENSOR message to appear on the
multi-inf ormation display. This is
normal and not a cause f or concern.
11/07/20 18:55:22 31SJA670_425
ProCarManuals.com

CONT INUED
If the system senses a likely collision
with a vehicle or object ahead of you,
it alerts you with a visual alert or a
combination of a visual alert and an
audible alert.The visual alert is an amber colored
BRAKE message that flashes on the
multi-inf ormation display, the audible
alert is a constant beeping sound. If
one or more of the alerts come on,
take the appropriate means to
prevent a collision (apply the brakes,
change lanes, etc.). Collision Alarm
Collision Mitigation Braking System (CMBS )
Driving
421
TM TM
11/07/20 18:55:27 31SJA670_426
ProCarManuals.com

µµ
Î
Î
e-pretensioner The radar sensor
detects a vehicle.Braking Audio & Visual
WARNING
Stage one
Stage threeDistance between vehiclesCMBS
Stage two
Retracts the driver’s
seat belt gently a few
times, providing a
physical warning.
Forcef ully tightens
driver and front
passenger seat belts. There is a risk of a
collision with the
vehicle ahead of you.
The risk of a collision
hasincreased,timeto
respond is reduced.
The CMBS
determines that a
collision is
unavoidable.Lightly
applied
Forcefully
applied ‘‘BRAKE’’ f lashes
on the multi-
information
display.
A beep sounds
and ‘‘BRAKE’’
f lashes on the
multi-information
display.
:
Depending on the circumstances, CMBS may not go through all of the alert stages bef ore initiating the last stage.
Collision Mitigation Braking System (CMBS )
422
YOUR
VEHICLE YOUR
VEHICLE
YOUR
VEHICLEVEHICLE
AHEADVEHICLE
AHEAD
VEHICLE
AHEAD
TM TM
11/07/20 18:55:36 31SJA670_427
ProCarManuals.com

Any of the conditions below can
cause the CMBS to shut of f . When
the system shuts off, the CMBS
indicator in the instrument panel
comes on, and a CHECK CMBS
SYSTEM message appears on the
multi-inf ormation display f or about 5
seconds.
An abnormal tire condition is
detected (wrong tire size, f lat tire,
etc.).
Extended off-road or mountainous
driving.
Driving your vehicle with the
parking brake applied.
Driving your vehicle in bad
weather(rain,fog,snow,etc.).
A dirty radar sensor cover on the
f ront grille. To switch the CMBS of f , press the
CMBS OFF button on the dashboard
f or about 1 second. When you do this,
a beeper sounds, a CMBS indicator
on the instrument panel comes on,
and a CMBS OFF message appears
on the multi-information display. To
switch the system back on, press the
button again f or about 1 second.When you turn the ignition switch to
the ON (II) position, the system will
be in the previously selected on or
off setting.
CONT INUED
Collision Mitigation Braking System (CMBS )
Automatic Shut Of f CMBS OFF Button
Driving
423
CMBS OFF BUTTON
TM TM
11/07/20 18:55:46 31SJA670_428
ProCarManuals.com