Acura RSX 2002 Owner's Manual

µ
The SAE numbers tell you the oil’s
viscosity or weight. Select the oil f or
your car according to this chart.
An oil with a viscosity of 5W-30 is
pref erred f or improved f uel economy
and year-round protection in your
Acura. You may use a 10W-30 oil if
the temperature in your area never
goes below 20°F ( 7°C).
5W-20 oil is f ormulated f or year-
round protection of your Acura, to
improve cold weather starting, and
to help your engine use less f uel.
If 5W-20 oil is not available, a 5W-30
oil may be used. However, it should
be replaced with 5W-20 at the next
oil change.
RSX and Premium models
Type-S
Engine Oil
Maint enance208
A Am
m b
bi
ieen n t
t T
Te
emm p
pe
erraat tuu r
ree
A
A m
m b
bi
ieen n t
t T
Te
emm p
pe
erraat tuu r
ree

Always change the oil and f ilter
accordingtothetimeanddistance
(miles/kilometers) recommenda-
tions in the maintenance schedule.
The oil and f ilter collect contami-
nants that can damage your engine if
they are not removed regularly.
Your Acura does not need any oil
additives. Purchasing additives f or
the engine or transmission will not
increase your car’s perf ormance or
longevity. It only increases the cost
of operating your car.
Changing the oil and f ilter requires
special tools and access f rom
underneath the car. The car should
be raised on a service station-type
hydraulic lif t f or this service. Unless
you have the knowledge and proper
equipment, you should have this
maintenancedonebyaskilled
mechanic.
You may use a synthetic motor oil if
it meets the same requirements
given f or a conventional motor oil: it
displays the API Certif ication Seal,
and it is the proper weight as shown
on the chart. When using synthetic
oil, you must f ollow the oil and f ilter
change intervals given in the
maintenance schedule.
CONT INUED
Synthetic Oil
Additives Changing the Oil and Filter
Engine Oil
Maint enance209

Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available f rom your Acura
dealer) is required to remove the
f ilter.
Install a new oil f ilter according to
instructions that come with it.
Open the hood and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
Run the engine until it reaches
normal operating temperature,
then shut it off.
4. 3.
2.
1.
Engine Oil
Maint enance210
O OI
ILL F
FIILLT T E
ER
R
W
WA AS
SHH E
ER
R
O
OIILL D
DR
RAA I
INN B
BOOL LTT

Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick. Let the engine run f or several
minutes and check the drain bolt
and oil f ilter f or leaks.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.
Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter): 7.
8.
9.
5.
6.
(RSX and Premium models)
(Type-S)
(RSX and Premium models)
(Type-S)
Engine Oil
Maint enance211
33 lbf·ft (44 N·m , 4.5 kgf·m)
29 lbf·ft (39 N·m , 4.0 kgf·m)
4.4 US qt (4.2
, 3.7 Imp qt)
5.0 US qt (4.7
, 4.1 Imp qt) Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system f or leaks.
This coolant should always be a
mixtureof 50percentantifreezeand
50 percent water. Never add straight
antif reeze or plain water. Always use Honda All Season
Antif reeze/Coolant Type 2. This
coolant is pre-mixed with 50 percent
antif reeze and 50 percent water. It
does not require any additional
mixing. If it is not available, you may
use another major-brand non-silicate
coolant as a temporary replacement.
Make sure it is a high-quality coolant
recommended f or aluminum engines.
However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling
system to malf unction or f ail. Have
the cooling system f lushed and
ref illed with Honda antif reeze/
coolant as soon as possible.
A dding Engine Coolant
Cooling Syst em
Maint enance212
M M
I
INN
M
M
A
AX
X
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.

Make sure the engine and
radiator are cool.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Remove the radiator cap by
pushing down and turning
counterclockwise.Put the radiator cap back on.
Tighten it f ully. The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents. 6.
5. 4.
2.
3. 1.
Cooling Syst em
Maint enance213
R RA
A D
DI
IAA T
TO
OR R C
CAA P
P
R
REES
SE ER
RV V E
E T
TA
A N
NK K

Openthehood.Makesurethe
engine and radiator are cool to the
touch.
Remove the radiator cap.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance
done by a skilled mechanic.
Remove the cover under the
radiator.
Turn the ignition ON (II). Turn
the temperature control dial to
maximum heat. Turn the ignition
off.
1.
2.
3. 4.
Cooling Syst em
Maint enance
Replacing Engine Coolant
214
C CO
OV VE
ER
R

CONT INUED
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator up to the base of the
f iller neck. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.
Loosen the drain plug on the
bottom of the radiator. Drain the
coolant into an appropriate
container.
When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator. Remove the clip, then remove the
reserve tank drain cap. Drain the
coolant into an appropriate
container.
Install the reserve tank drain cap
and clip.
5.
6.
7.8.
Cooling Syst em
Maint enance215
F FI
ILLL LEE R
R N
NEEC
CK K
C
CL LIIPP
D
D R
RAA I
INN
C
CA A P
P
D
D R
RAA I
INN P
PL
LUUG G
F
Fiillll u
u p
p t
too h
he
erree

Check the level in the windshield
washer reservoir at least monthly
during normal usage. In bad weather,
when you use the washers of ten,
check the level every time you stop
f or f uel. This reservoir supplies the
windshield and rear window washers.
The cooling system capacity is:
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine.
Fill the radiator with coolant up to
the base of the f iller neck.
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
Install the radiator cap, and
tighten it to the first stop.
Start the engine and let it run until
the radiator cooling f an comes on
at least twice. Then stop the
engine. Remove the radiator cap. Fill the
radiator with coolant up to the
base of the f iller neck.
Start the engine and hold it at
1,500 rpm until the radiator f an
comes on. Turn of f the engine.
Check the coolant level in the
radiator and add coolant if needed.
Install the radiator cap, and
tighten it fully.
If necessary, f ill the reserve tank
to the MAX mark. Install the
reserve tank cap.
9.
11. 10.
12.
13. 14.
15.
16. 17.
With automatic transmission:
Manual Transmission:
Maint enance
Cooling System, Windshield Washers
Windshield Washers
216
1.35 US gal (5.1, 1.12 Imp gal)
1.32 US gal (5.0
, 1.10 Imp gal)

The windshield washer reservoir is
located behind the driver’s side
headlight. Check the reservoir’s f luid
level by removing the cap and
looking at the level gauge attached
to the cap.
Fill the reservoir with a good-quality
windshield washer f luid. This
increases the cleaning capability and
prevents f reezing in cold weather.When you ref ill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer f luid
on a clean cloth. This will help to
condition the blade edges.
Remove the dipstick (yellow loop)
f rom the transmission and wipe it
with a clean cloth. Park the car on level ground. Shut
of f the engine.
Check the f luid level with the engine
at normal operating temperature.
1.
2.
CONT INUED
Maint enance
Windshield Washers, T ransmission Fluid
Automatic Transmission
217
W WI
INND DS
SHH I
IEE L
LDD W
WA AS
SHH E
ER
R R
REES
SE ER
RV V O
OI IRR
L
LE E V
V E
EL
L G
GAAU
UG GEE D
D
I
IPP S
ST TI
ICCK K
Do not use engine antif reeze or a
vinegar/water solution in the
windshield washer reservoir.
Antif reeze can damage your car’s paint,
while a vinegar/water solution can
damage the windshield washer pump.
Use only commercially-available
windshield washer f luid.