reset Acura RSX 2002 Owner's Manual

µ
This indicator reminds you that it is
time to take your car in for
scheduled maintenance.
Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages
.For the f irst 8,000 miles (12,800 km)
af ter the Maintenance Required
Indicator is reset, it will come on f or
two seconds when you turn the
ignition switch ON (II).
Between 8,000 miles (12,800 km)
and 10,000 miles (16,000 km) this
indicator will light f or two seconds
when you f irst turn the ignition
switch ON (II), and then f lash f or
ten seconds.
If you exceed 10,000 miles (16,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
198 202
Indicator L ights
Inst rument s and Cont rols
Maintenance Required Indicator
64
M M A
AI
INNT TE
EN
NA AN
NC CEE R
REEQ
QU UIIRRE ED
D I
INND DI
ICCA A T
TO
OR R

Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Acura dealer, reset the indicator as
f ollows.Turn of f the engine.
Press and hold the select/reset
button in the instrument panel,
then turn the ignition switch ON
(II).
Hold the button until the indicator
resets (approximately ten
seconds).This indicator lights when the
security system is set. See page
f or complete inf ormation on the
security system.
1.
2.
3. 148
Indicator L ights
Inst rument s and Cont rols
Security System Indicator
65
S SE
EL
LEE C
CT T/
/R
RE ES
SE ET
T B
BUUT TT
TO
ON N
S
SEEC
CU UR RIITT Y
Y S
SYYSSTTE
EM
M I
INND DI
ICCA A T
TO
OR R

This shows your speed in miles per
hour (mph). The smaller inner
numbers are the speed in kilometers
per hour (km/h).
This shows your speed in kilometers
per hour (km/h). The smaller inner
numbers are the speed in miles per
hour (mph).The tachometer shows the engine
speed in revolutions per minute
(rpm). To protect the engine f rom
damage, never drive with the
tachometer needle in the red zone.The odometer shows the total dis-
tance your car has been driven. It
measures miles in U.S. models and
kilometers in Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.
U.S. Models
Canadian Models
Speedometer Odometer
T achometer
Gauges
Inst rument s and Cont rols66
T T E
EM
M P
PE
ER
RA A T
TU
UR REE G
GAAU
UG GEE T
TA
A C
CHH O
OM M E
ET
TE
ER
R S
SPPE
EE
ED
D O
OM M E
ET
TE
ER
R F
FUUE EL
L G
GAAU
UG GEE
S
SE EL
LEE C
CT T/
/R
RE ES
SE ET
T B
BUUT TT
TO
ON N
O
OD DO
OM M E
ET
TE
ER
R/ /T
T R
RI IPP M
M E
ET
TE
ER
R

This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to near
the upper white mark. If it reaches
the red (Hot) mark, pull safely to the
side of the road. Turn to page f or
instructions and precautions on
checking the engine’s cooling
system.
This shows how much f uel you have.
It is most accurate when the car is on
level ground. It may show slightly
more or less than the actual amount
whenyouaredrivingoncurvyor
hilly roads.
The needle returns to the bottom
after you turn off the ignition. The
gauge shows the f uel level reading
immediately af ter you turn the
ignition switch back ON (II).
This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
To reset a trip meter, display it, and
then press and hold the Select/Reset
button until the number resets to
‘‘0.0’’. There are two trip meters: Trip A
and Trip B. Switch between these
displays and the odometer by
pressing the Select/Reset button
repeatedly. Each trip meter works
independently, so you can keep track
of two dif f erent distances.
212
Gauges
Inst rument s and Cont rols
Temperature Gauge
Fuel Gauge
Trip Meter
67

To open or close the driver’s window
partially, push down or pull back on
the window switch lightly and hold it.
The window will stop when you
release the switch.
If the driver’s window runs into any
obstacle while it is closing
automatically, it will stop, and then
reverse direction. To close the
window, remove the obstacle, then
use the window switch again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it.The MAIN switch controls power to
the passengers’window. With this
switch of f , the passengers’window
cannot be raised or lowered. The
MAIN switch does not af f ect the driv-
er’s window. Keep the MAIN switch
off whenyouhavechildreninthecar
so they do not injure themselves by
operating the window unintentionally.
The lights inside the switches come
onwhenyouturntheparkinglights
or headlights on.
If your car’s battery is disconnected
or goes dead, or the driver’s window
f use is removed, the AUTO f unction
will be disabled. The power window
system needs to be reset af ter
reconnecting the battery or installing
the f use. You should do the f ollowing.
Start the engine. Push down on
the driver’s window switch until
the window is f ully open.
Pull back on the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more.
If the power windows do not operate
properly af ter resetting, have your
car checked by an Acura dealer. 1.
2.
Auto Reverse
Power Windows
Inst rument s and Cont rols92

CONT INUED
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is broad-
castinginstereo.Stereo
reproduction on AM is not available.
The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pushing the PWR/
VOL knob. Adjust the volume by
turning the same knob.
Your Acura’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.
The anti-thef t f eature will disable the
system if it is disconnected f rom the
vehicle’s battery. To get the system
working again, you must enter a
code number (see page ).
147
All models except Type-S
Audio System
AM/FM/CD Audio System
Operating the Radio
Comf ort and Convenience Feat ures109

µµµ
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob clockwise to tune to a
higher f requency, or
counterclockwise to tune to a lower
f requency. You can use any of f ive methods to
find radio stations on the selected
band: TUNE, SEEK, SCAN, AUTO
SELECT, and the Preset buttons.
To change the f requency rapidly,
press and hold the top or bottom of
theSEEKbar.Releasethebarwhen
the display reaches the desired
f requency. Depending on which part
of the bar you press, the system
scans upward or downward f rom the
current f requency. The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
and release the top or bottom of the
SEEK bar. Depending on which part
of the bar you press, the system
scans upward or downward f rom the
current f requency. It stops when it
finds a station with a strong signal. The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. The system will scan
up the band for a station with a
strong signal. When it f inds one, it
will stop and play that station f or
approximately f ive seconds. If you do
nothing, the system will then scan
f or the next strong station and play
that f or f ive seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again.
TUNE
SEEK
SCA N
Audio System
Comf ort and Convenience Feat ures110

µ
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM. Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep. Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each Preset
button.
To store a f requency:
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset f requencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio f use is
removed.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
1.
2.
3.
4. Preset
Audio System
Comf ort and Convenience Feat ures111
A A
M
M /
/F
FM M B
BUUT TT
TO
ON N
S
STTE
ER
RE EO
O I
INND DI
ICCA A T
TO
OR R
S
SC CAA N
N I
INND DI
ICCA A T
TO
OR R
P
P R
RE ES
SE ET
T B
BUUT TT
TO
ON NSS A
A
U
UT TO
O
S
SE EL
LEE C
CT T
B
BU UT TT
TO
ON N
S
SC
CAA N
N
B
BU UT TT
TO
ON N
P
P W
WR R//V
V O
OL L K
KNNO OBB
T
TU
UN NEE/
/M
M O
ODDE
E K
KNNO OBB
S
SE EE
EK
K/ /S
SK KIIPP B
BAA R
R

µIf you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
If you are in a remote area, Auto
Select may not f ind six strong AM
stations or twelve strong FM stations.
If this happens, you will see a ‘‘0’’
displayed when you press any preset
button that does not have a station
stored. To activate Auto Select, press the
A. SEL button. A. SEL will f lash in
the display, and the system will go
into scan mode f or several seconds.
It automatically scans both bands,
looking f or stations with strong
signals. It stores the f requencies of
six AM stations and twelve FM
stations in the preset buttons. You
can then use the preset buttons to
select those stations. If you do not like the stations Auto
Select has stored, you can store
other f requencies in the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind the desired
f requencies, then store them in the
selected preset buttons as described
previously.Auto Select does not erase the
f requencies that you preset pre-
viously. When you return home, turn
of f Auto Select by pressing the
A. SEL button. The preset buttons
will then select the f requencies you
originally set.
AUTO SELECT
Audio System
Comf ort and Convenience Feat ures112

To set the hours, press and hold the
CLOCK button. Press and hold the
H button until the numbers advance
to the desired time.
To set the minutes, press and hold
the CLOCK button. Press and hold
the M button until the numbers
advance to the desired time.YoucanusetheRESbuttonto
quickly set the time to the nearest
hour. Press the RES button while
pressing the CLOCK button. If the
displayed time is bef ore the half
hour, pressing RES sets the clock
back to the previous hour. If the
displayed time is af ter the half hour,
pressing RES sets the clock f orward
to the beginning of the next hour. 1:06 would RESET to 1:00
1:52 would RESET to 2:00
If your car’s battery is disconnected
or goes dead, the time setting will be
lost. To set the time again, f ollow the
setting procedure.
The audio system usually shows the
time when the ignition switch is in
ACCESSORY (I) or ON (II). It
shows the operation mode of the
radio, CD player, or optional CD
changer when you operate them,
then goes back to the time display
af ter three seconds.
For example :
Digital Clock
Audio System
Comf ort and Convenience Feat ures114