ignition Acura TL 2000 3.2 Service Manual

Automatic Transmission
First (1) - With the lever in this
position, the transmission locks in
First gear.
If you shift into First position when
the vehicle speed is above 31 mph(50 km/h), the transmission shifts
into Second gear first to avoid sudden engine braking. Engine Speed Limiter
If you exceed the maximum speed
for the gear you are in, the engine speed will enter into the tachometer's
red zone. If this occurs, you may feel
the engine cut in and out. This is caused by a limiter in the engine's
computer controls. The engine will
run normally when you reduce the
RPM below the red zone. Shift Lock Release
This allows you to move the shift lever out of Park if the normal
method of pushing on the brake
pedal does not work. This procedure
also releases the Reverse Lockout.
1. Set the Parking brake.
2. Make sure the key is in the ignition switch OFF (0) position.
To release the Reverse Lockout, make sure the key is in the
ACCESSORY (I) position.
CONTINUED
Driving

Traction Control System
TCS ON/OFF SwitchThis switch is under the side vent. It lets you turn the Traction ControlSystem on and off. You cannot turn
off the TCS while the TCS indicator
light is flashing. Deactivate the system by pressing
the TCS On/Off switch. The TCS indicator light comes on as a
reminder. Pressing the switch again
turns the system back on.
The Traction Control System turns on every time you start the engine,
even if you turned it off the last time
you drove the vehicle. TCS Indicator
The TCS indicator comes on or flashes under the following condi-
tions:
• When you turn the ignition switch
to ON (II)
• When you manually turn off theTCS.
• It flashes when the TCS is
regulating wheelspin.
• If the system's diagnostics senses a problem in the TCS, the indica-
tor will come on and stay on.
Driving

Cooling System
1. Turn the ignition ON (II). Turnthe heater temperature controldial to maximum heat (climate
control to 90°F/32°C). Turn off
the ignition. Open the hood. Make sure the engine and radiator are
cool to the touch.
2. Remove the radiator cap.
DRAIN PLUG
DRAIN BOLT
3. Loosen the drain plug on thebottom of the radiator. Thecoolant will drain through thesplash guard. Loosen the drain
bolt at the rear of the engine cylinder block.
RESERVE TANK CAP RESERVE TANK
HOLDER
4. Remove the reserve tank from itsholder by pulling it straight up.Drain the coolant, then put the
tank back in its holder.
5. When the coolant stops draining, tighten the drain plug at the
bottom of the radiator.
CONTINUED
Maintenance

Spark Plugs
The spark plugs in your car shouldbe replaced according to the time
and distance recommendations in
the maintenance schedule. Replacement
1. Remove the cover on the front cylinder bank by turning the two
clips one quarter turn
counterclockwise.
2. Clean up any dirt and oil that have collected around the ignition coils. 3. Disconnect the wire connector
from the ignition coil by pushingon the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
CONTINUED
Maintenance

Spark Plugs
4. Use a wrench to remove thehexagon socket head cap bolt
holding the ignition coil. Removethe ignition coil by pulling itstraight out
5. Remove the spark plug with a five-eighths inch (16 mm) spark
plug socket 6. Put the new spark plug into the
socket; then screw it into the hole.
Screw it in by hand so you do not crossthread it. 7. Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn after it contacts the cylinder head.)
Tightening torque:
13 Ibf-ft(18N-m,1.8kgf-m)
Maintenance

Spark Plugs
Tighten the spark plugs carefully. A
spark plug that is too loose can
overheat and damage the engine. Overtightening can cause damage to
the threads in the cylinder head. 8. Install the ignition coil. Reinstall
the hexagon socket head cap bolt.
9. Push the wire connector onto the ignition coil. Make sure it locks in
place.
10.Repeat this procedure for the other five spark plugs.
11.Reinstall the cover on the front cylinder bank. Specifications:
NGK:
DENSO: PZFR5F-11
PKJ16CR-L11
Spark Plug Gap:
0.04 in (1.1 mm)
Maintenance
NOTICE
+0—0.1 mm

Battery
If your car's battery is disconnectedor goes dead, the audio system will
disable itself. The next time you turn
on the radio you will see "Code" in
the frequency display. Use the Preset buttons to enter the five-digit
code (see page 142 ).
The Navigation System will also disable itself. The next time you turn
on the ignition switch, the system
will require you to enter a PIN
before it can be used. Refer to the Navigation System Owner's Manual.NOTICE
Charging the battery with the cables
connected can seriously damage your
car's electronic controls. Detach the
battery cables before connecting the
battery to a charger.
Maintenance

Wiper Blades
Check the condition of the wiper
blades at least every six months. Look for signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you find these signs, or they leave streaks
and unwiped areas when used.WIPER ARMS
To replace the blade:
1. Turn the ignition ON (II), switch the wipers to INT or — lowposition), then turn the ignition
OFF when the wiper arm is
approximately midway in its travel.
2. Raise the wiper arm off the windshield.
LOCK TAB
3. Disconnect the blade assemblyfrom the wiper arm by pushing in
the lock tab. Hold it in while you
push the blade assembly toward
the base of the arm.
CONTINUED
Maintenance

Wiper Blades
BLADE
4. Remove the blade from its holderby grasping the tabbed end of the
blade. Pull firmly until the tabs
come out of the holder.
BLADE
REINFORCEMENT
5. Examine the new wiper blades. If they have no plastic or metal rein-
forcement along the back edge,
remove the metal reinforcement
strips from the old wiper blade and
install them in the slots along the
edge of the new blade. 6. Slide the new wiper blade into the
holder until the tabs lock.
7. Slide the wiper blade assembly onto the wiper arm. Make sure it
locks in place.
8. Lower the wiper arm down against the windshield.
9. Turn the ignition switch ON (II) and return the windshield wipers
to their park position.
Maintenance

Changing a Flat Tire
If you have a flat tire while driving,stop in a safe place to change it.
Stopping in traffic or on the shoulder
of a busy road is dangerous. Driveslowly along the shoulder until you
get to an exit or an area to stop that
is far away from the traffic lanes.
The car can easily roll off the
jack, seriously injuring anyone underneath.
Follow the directions for
changing a tire exactly, and never get under the car when it
is supported only by the jack.HOOK
SPARE TIRE TOOL BOX
1. Park the car on firm, level, and non-slippery ground away from
traffic. Put the transmission inPark. Apply the parking brake.
2. Turn on the hazard warning lights and turn the ignition switch to
LOCK (0). Have all the
passengers get out of the car while
you change the tire. 3. Open the trunk. Raise the trunk
floor by lifting up on the back edge.
To keep the trunk floor out of the way, attach the hook into the slot in the trunk lid.
4. Unscrew the wing bolt and take the spare tire out of its well.
5. The tools are in the tool box on the right side of the trunk. Takethe tools out of the tool box.
CONTINUED
Taking Care of the Unexpected
TRUNK FLOOR
JACK