bulb Acura TL 2009 Owner's Manual

Î
Î
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.
If this indicator begins to f lash,
there is a problem with the tire
pressure monitoring system
(TPMS). You will also see a
‘‘CHECK TPMS SYSTEM’’
message on the multi-inf ormation
display. The indicator continues to
f lash f or a while (approximately 1
minute), then stays on. If this
happens, have your dealer check
the system as soon as possible.
For more inf ormation, see page
. This indicator normally comes on
when you turn the ignition switch to
the ON (II) position and goes of f
af ter the engine starts. If it comes on
at any other time, there is a problem
in the electric power steering system.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand .
2.
526 559563
:
180
178
Instrument Panel Indicators
Electric Power Steering
(EPS) Indicator
Turn Signal and
Hazard Warning
Indicators
70
\f—
—y
y
) \f\fy\f\fy
2009 TL

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk, readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or another qualif ied
technician.Your vehicle has halogen high beam
headlight bulbs which are also used
f or the daytime running light.
Handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Open the hood.
Remove all engine compartment
covers (see page ). If youarereplacingthebulbon
the driver’s side, remove the three
holding clips with a f lat-tipped
screwdriver. Then remove the
upper part of the air intake duct by
pulling it straight up.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed (or the vehicle
is in VEHICLE OFF (LOCK) mode
on models with keyless access
system). Because of this, you should
not attempt to examine or change a
low beam headlight bulb yourself . If
a low beam headlight bulb fails, take
the vehicle to your dealer to have it
replaced.
1.
2.
546
Headlight A iming
L ow Beam Headlight Bulb
Replacement
Replacing a High Beam
Headlight/Daytime Running
Light Bulb
Lights
556
HOLDING CLIP
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
\f—
—y

y
) \f\fy\f
y
2009 TL

Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the lights to test the new
bulb.
(Driver’s side)
Install the upper part of the air
intake duct.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place. Install the engine coolant reserve
tank.
(Passenger’s side)
Install the all engine compartment
covers.
To change a bulb on the
passenger’s side, remove the
engine coolant reserve tank by
pulling it out of its stay.
4.
5. 6.
7.
8.
3. 9.
10.
Lights
Maint enance
557
RESERVE TANK BULB
CONNECTOR
STAY
\f—\f—y

\fy
) \f\fy\fy
2009 TL

Start the engine. If you are
replacing a driver’s side bulb, turn
the steering wheel all the way to
theright.If youarereplacinga
passenger’s side bulb, turn the
steering wheel to the lef t. Turn of f
the engine.Use a f lat-tipped screwdriver to
remove the holding clips f rom the
edge of the inner f ender cover,
and pull the inner f ender cover
back.
Remove the two undercover bolts
and the holding clip with a f lat-
tipped screwdriver.
3.
2.
1.
Replacing the Front Side Marker
Light Bulb
Lights
558
BOLTS
HOLDING CLIP
SPOILER
HOLDING
CLIP
\f—\f—y

\fy
) \f\fy\fy
2009 TL

CONT INUED
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Start the engine. If you are
replacing a driver’s side bulb, turn
the steering wheel all the way to
theright.If youarereplacinga
passenger’s side bulb, turn the
steering wheel to the lef t. Turn of f
the engine.
Remove the bulb by pulling it
straight out of its socket. Install the new bulb in the socket
by pushing it straight in the socket
until it bottoms.
Insert the socket into the
headlight assembly. Turn it
clockwise to lock it in place.
Test the lights to make sure the
new bulb is working.
Set the spoiler and inner f ender
cover in the original position.
Install the bolts and holding clips,
andlocktheminplacebypushing
on their center.
4.
5. 6.
7.
8.
1.
9.
Lights
Replacing a Front T urn Signal/
Parking L ight Bulb
Maint enance
559
SOCKET
BULB
\f—\f—y


\fy
) \f\fy\fy
2009 TL

Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Remove the bulb f rom the socket
bypushingitinandturningit
counterclockwise until it unlocks.
Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the inner f ender.
Use a 10 mm wrench to remove
the two mounting bolts and
remove the holding clip with a flat-
tipped screwdriver.
Pull down the under cover f rom
the bumper caref ully.
3.
2. 4.
5.
Lights
560
HOLDING CLIP
SOCKET
BULB
COVER
HOLDING
CLIP
SPOILERBOLTS
\f—\f—y



y
) \f\fy\fy
2009 TL

CONT INUED
Install the new bulb in the socket.
Turn it clockwise to lock it in place.
Insert the socket into the light
assembly. Turn it clockwise to
lock it in place.
Testthelightstomakesurethe
new bulb is working.Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Start the engine. If you are
replacing a driver’s side bulb, turn
the steering wheel all the way to
theright.If youarereplacinga
passenger’s side bulb, turn the
steering wheel to the lef t. Turn of f
the engine.
Push the under cover in place and
set the spoiler and inner f ender
cover in the original position.
Install the bolts and holding clips,
andlocktheminplacebypushing
on their center.
Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the inner f ender.
6.
7.
8.
9.
2.
1.
Lights
Replacing a Front Fog L ight Bulb
Maint enance
561
HOLDING CLIP
COVER
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
\f—\f—y


y
) \f\fy\fy
2009 TL

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Use a 10 mm wrench to remove
the two mounting bolts and
remove the holding clip with a flat-
tipped screwdriver.
Pull down the under cover f rom
the bumper caref ully. Push the under cover in place and
set the spoiler and inner f ender
cover in the original position.
Install the bolts and holding clips,
andlocktheminplacebypushing
on their center.
4.
5. 6.
7.
8.
3. 9.
Lights
562
BULB
HOLDING
CLIP
SPOILER CONNECTOR
BOLTS
\f—\f—y


y
) \f\fy\fy
2009 TL

CONT INUED
Remove the three stud bolts with a
socket or wrench.
Open the trunk.
Remove the screw in the center of
theholdingcliponthesideof the
trunk lining. Pull the lining back. Pull the taillight assembly straight
back out of the body.
1. 2. 3.
Lights
Replacing Rear Bulbs
Maint enance
563
SCREW
BOLTS
\f—\f—y


y
) \f\fy\fy
2009 TL

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Push a new bulb straight into the
socket until it bottoms, and
reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthenewbulbtomakesureit
works.
Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
Put the holding clip into the hole
on the side of the trunk lining.
Reinstall the screw.
Remove the socket by turning it
one-quarter turn counterclockwise,
and pull the bulb straight out of its
socket.
Determine which of the three
bulbs is burned out: back-up light,
turn signal, or side marker. 6.
7.
8.
9.
5.
4.
Lights, Cleaning the Seat Belts
Cleaning the Seat Belts
564
OPENING
BULB SOCKET
\f—\f—y



y
) \f\fy\fy
2009 TL