ignition Acura TL 2009 Owner's Manual

ÛÝ
Î Î
Î Î
CONT INUED
Select ‘‘RESET’’ by pressing the
INFO ( / ) button, then press
the SEL/RESET button to reset
the engine oil lif e display. The
maintenance item code(s) will
disappear, and the engine oil lif e
will reset to ‘‘100.’’ If you want to
cancel the oil lif e reset mode,
select ‘‘CANCEL.’’
Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100%’’ on the display the
next time you turn the ignition
switch to the ON (II) position.
Turn the ignition switch to the
ON (II) position.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages and . Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows: Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
mode will be shown on the multi-
inf ormation display.
If the engine oil lif e is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly.
3.
1.
2. 4.
: :
178180 178180
Maintenance Minder
Resetting the Engine Oil Lif e
Display
Maint enance
541
\f—
—y
y
) \f\fy\fy
2009 TL

Take the tool case out of the spare
tire.
Unscrew the wing bolt and take
the spare tire out of its well.
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area that is
far away from the traffic lanes.
Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park. Apply the
parking brake.
Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.
Models equipped with the keyless
access system have an engine start/
stop button instead of an ignition
switch. VEHICLE OFF (LOCK)
Mode is the equivalent of LOCK (0).
See page f or ignition switch and
power mode comparison. Open the trunk. Raise the trunk
f loor by lif ting up on the back edge.
5.
4.
3.
2.
1.
180
CONT INUED
Changing a Flat Tire
T aking Care of t he Unexpect ed
583
EXTENSION WHEEL NUT
WRENCH
JACK
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.
\f—\f—\fy\f

\fy
) \f\fy\fy
2009 TL

Check these things:Check the transmission interlock.
The shift lever must be in Park or
neutral.
Turn the ignition switch to the ON
(II) position or on models with
keyless access system, press the
engine start/stop button to set ON
Mode (see page ). Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See on page .
When you turn the ignition switch to
the START (III) position or on
models with keyless access system,
press the engine start/stop button to
set START Mode (see page ),
you do not hear the normal noise of
the engine trying to start. You may
hear a clicking sound, a series of
clicks, or nothing at all.
Diagnosing why the engine won’t
start f alls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position or on models with keyless
access system, press the engine
start/stop button to set START
Mode (see page ):
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. 591
180
180
180
If theEngineWon’tStart
Nothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting
588
\f—\f—y

y
) \f\fy\fy
2009 TL

In this case, the starter motor’s
speed sounds normal, or even f aster
than normal, when you turn the
ignition switch to the START (III)
position or on models with keyless
access system, press the engine
start/stop button to set START
Mode (see page ), but the engine
does not run.Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page ).
Turn the ignition switch to the
START (III) position or on models
with keyless access system, press
the engine start/stop button to set
STARTMode(seepage ).If
the headlights do not dim, check
the condition of the fuses. If the
f uses are OK, there is probably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualif ied technician to
determine the problem. See
on page .If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page ). You can
then try jump starting the vehicle
f rom a booster battery (see page
).
65
180
180
591577
606
CONT INUED
T he Starter Operates Normally
Emergency T owing
If theEngineWon’tStart
T aking Care of t he Unexpect ed
589
\f—\f—\fy\f

y
) \f\fy\fy
2009 TL

Î
ÎIf the f luid level is low, take your
vehicle to a dealer, and have the
brake system inspected f or leaks or
worn brake pads.
However, if the brake pedal does not
f eel normal, you should take
immediate action. A problem in one
part of the system’s dual circuit
design will still give you braking at
two wheels. You will f eel the brake
pedal go down much f arther bef ore
the vehicle begins to slow down, and
you will have to press harder on the
pedal. You will also see a ‘‘LOW BRAKE
FLUID’’ message on the multi-
inf ormation display.
You will also see a ‘‘CHECK BRAKE
SYSTEM’’ message on the multi-
inf ormation display when this
indicator comes on.
To check if they are set, turn the
ignition switch to the ON (II)
position (set ON mode on models
with keyless access system), without
starting the engine. The malf unction
indicator lamp will come on f or 20
seconds. If it then goes of f , the
readiness codes are set. If it blinks
f ive times, the readiness codes are
not set. If possible, do not take your
vehicle f or an emissions test until the
readiness codes are set. Ref er to
for more
inf ormation (see page ). Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
If the brake system indicator comes
on while driving, the brake f luid level
is probably low. Press lightly on the
brake pedal to see if it f eels normal.
If it does, check the brake f luid level
thenexttimeyoustopataservice
station (see page ). The brake system indicator normally
comes on when you turn the ignition
switch to the ON (II) position, and
as a reminder to check the parking
brake. It will stay on if you do not
f ully release the parking brake.
555
626
:
178 180
CONT INUED
Malf unction Indicator L amp, Brake System Indicator
Brake System
Indicator
Emissions T esting
T aking Care of t he Unexpect ed
597
Canada
U.S.
—
—y

y
) yy
2009 TL

Also check the combined f use box in
the under-hood f use box.
If something electrical in your
vehicle stops working, the first thing
youshouldcheckforisablownfuse.
Determine f rom the chart on pages
, and , or the diagram on
thefuseboxlidorthefuselabel,
which f use or f uses control that
component. Check those f uses f irst,
but check all the f uses bef ore
deciding that a blown f use is not the
cause. Replace any blown f uses and
check if the device works.
Turn the ignition switch to the
LOCK (0) position. Make sure the
headlights and all other
accessories are of f . Check each of the large f uses in
the under-hood f use box by
looking at the wire inside.
Removing these f uses requires a
Phillips-head screwdriver. Remove the cover f rom the f use
box.
Models equipped with the keyless
access system have an engine
start/stop button instead of an
ignition switch. VEHICLE OFF
(LOCK) Mode is the equivalent of
LOCK (0). See page for
ignition switch and power mode
comparison. 3.
1.
2.
603 604 605
180
Checking and Replacing Fuses
Fuses
600
FUSE
BLOWN BLOWN
——y

y
) yy
2009 TL

µµ
If your vehicle needs to be towed,
call a prof essional towing service or
organization. Never tow your vehicle
with just a rope or chain. It is very
dangerous.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock. Turn of f the engine. Shif t to D position f or 5 seconds,
then to N. Start the engine. Release the parking brake.
Therearetwowaystotowyour
vehicle:
The operator
loads your vehicle on the back of a
truck.
The operator will load
your vehicle on the back of a truck.
Any other method of towing will
damage the drive system. When you
contact the towing agency, inf orm
them a f lat-bed is required. If , due to damage, your vehicle must
be towed with the f ront wheels on
the ground, do this:
Models equipped with the keyless
access system have an engine start/
stop button instead of an ignition
switch. ACCESSORY Mode is the
equivalent of ACCESSORY (I). See
page f or ignition switch and
power mode comparison.
The tow
truck uses two pivoting arms that go
under the f ront tires and lif t them of f
the ground. The rear tires remain on
the ground.
180
(On SH-AWD models)(Except SH-AWD models)
Emergency Towing
Flat -bed Equipment
Wheel-lif t Equipment
T his is the best way to
transport your vehicle.
The only way you can saf ely tow
your vehicle is with f lat-bed
equipment.
This is an acceptable
way to tow your vehicle.
606
Towing with only two tires on the
ground will damage parts of the
all-wheel-drive system. Your vehicle
should be transported on a f lat-bed
truck or trailer.
——y


y
) y

y
2009 TL

ÎÎ
Î
With the f ront wheels on the ground,
it is best to tow the vehicle no farther
than 50 miles (80 km), and keep the
speedbelow35mph(55km/h).
If your vehicle is equipped with a
f ront spoiler, remove it bef ore
towing so it is not damaged. Models equipped with the keyless
access system have an engine start/
stop button instead of an ignition
switch. ACCESSORY Mode is the
equivalent of ACCESSORY (I). See
page f or ignition switch and
power mode comparison.
If you decide to tow your vehicle
with all f our wheels on the ground,
make sure you use a properly-
designed and attached tow bar.
Prepare the vehicle for towing as
described above, and leave the
ignition switched in the
ACCESSORY (I) position so the
steering wheel does not lock. Make
sure the radio and any items plugged
into the accessory power socket are
turned of f so they do not run down
the battery. 178
CONT INUED
Emergency Towing
T aking Care of t he Unexpect ed
607
Trying to lif t or tow your vehicle by the
bumpers will cause serious damage.
The bumpers are not designed to
support the vehicle’s weight. Improper towing preparation will
damage the transmission. Follow the
above procedure exactly. If you cannot
shif t the transmission or start the
engine, your vehicle must be
transported with the f ront wheels of f
the ground.
The steering system can be damaged if
the steering wheel is locked. Leave the
ignition switch in the ACCESSORY (I)
position, and make sure the steering
wheel turns f reely bef ore you begin
towing.On models with the Keyless Access
system, the ENGINE START/STOP
BUTTON indicator will conf irm that
the power mode is in the ACCESSORY
mode and that the steering lock is
released. If the steering wheel does not
turn f reely, rotate the wheel right and
lef t while pressing the ENGINE
START/STOP BUTTON. This
inf ormation also appears on the multi-
inf ormation display (see page ).
182
—
—y
y
) y
y
2009 TL

The exhaust emissions controls
include f our systems: PGM-FI,
ignition timing control, exhaust gas
recirculation, and three way catalytic
converter. These f our systems work
together to control the engine’s
combustion and minimize the
amount of HC, CO, and NOx that
come out the tailpipe. The exhaust
emissions control systems are
separate f rom the crankcase and
evaporative emissions control
systems.The emissions control systems are
designed and certif ied to work
together in reducing emissions to
levels that comply with the Clean Air
Act. To make sure the emissions
remain low, you should use only new
Acura replacement parts or their
equivalent f or repairs. Using lower
qualitypartsmayincreasethe
emissions f rom your vehicle.
The emissions control systems are
covered by warranties separate from
the rest of your vehicle. Read your
warranty manual for more informa-
tion.
The PGM-FI system uses sequential
multiport f uel injection.
It has three subsystems: air intake,
engine control, and f uel control. The
powertrain control module (PCM)
uses various sensors to determine
how much air is going into the
engine. It then controls how much
f uel to inject under all operating
conditions. This system constantly adjusts the
ignition timing, reducing the amount
of HC, CO, and NOx produced.
The exhaust gas recirculation (EGR)
system takes some of the exhaust
gas and routes it back into the intake
manif old. Adding exhaust gas to the
air/f uel mixture reduces the amount
of NOx produced when the f uel is
burned.
The three way catalytic converter is
in the exhaust system. Through
chemical reactions, it converts HC,
CO, and NOx in the engine’s exhaust
to carbon dioxide (CO ), nitrogen
(N ), and water vapor.
2
2
Exhaust Emissions Controls Replacement Parts
PGM-FI SystemIgnit ion T iming Cont rol Syst em
Exhaust Gas Recirculat ion (EGR)Syst em
Three Way Catalytic Converter
Emissions Cont rols
624
\f—\f—y

y
) \f\fy\fy
2009 TL

CONT INUED
............................
Capacities Chart .614
.............
Carbon Monoxide Hazard .57
Battery
Charging System ...........................
Indicator .65,595
............................
Jump Starting .591
..............................
Maintenance .577
............................
Specif ications .615
..............................
Bef ore Driving .485
....................................
Belts,Seat .8,20
...........................
Beverage Holder .203
.......
Bluetooth
HandsFreeLink.392 Brakes
...........
Anti-lock System (ABS) .521
.............
Break-in, New Linings .486
...........................................
Fluid .555
.......................................
Parking .201
.................
System Indicator .65,597
........................
Wear Indicators .520
.............................
Braking System .520
.................
Break-in, New Vehicle .486
Brightness Control,
...............................
Instruments .137
....................................
Built-In Key .142
Bulb Replacement ..........................
Back-up Lights .563
.........
Daytime Running Lights .556
.................................
Fog Lights .561
............................
Specif ications .345
............
Turn Signal Lights .559,563
..............................
Bulbs, Halogen .556
................................
AAC .265,307,357
...
Accessories and Modif ications .495
................................
Accessories .495
............................
Modif ications .496
ACCESSORY (Ignition Key .....................................
Position) .145
ACCESSORY Mode ...........................
(Power Mode) .178
............
Accessory Power Sockets .204
......................................
AcuraLink .467
................
Adding Engine Coolant .550
........................
Adding Engine Oil .547
....................
Additives, Engine Oil .548
...............................
Airbag (SRS) .9,24
...............
Additional Information .24
......................................
Servicing .35
...................
System Components .24
..............
Air Conditioning System .214
.......................
Air Pressure, Tires .568
......................................
Antif reeze .550
Anti-lock Brakes (ABS) ...............................
Indicator .66,521
...................................
Operation .521
..............
Anti-thef t, Audio System .376 Anti-thef t Steering Column
............................................
Lock .145
................................
Audio System .223
.
Automatic Lighting Off Feature .135
...
Automatic Seat Belt Tensioners .22
.............
Automatic Speed Control .386
..............
Automatic Transmission .507
..........................
Capacity, Fluid .614
...............
Checking Fluid Level .553
.......................................
Shif ting .508
.
Shif t Lever Position Indicator .507
....................
Shif t Lock Release .510
Index
A
BC
INDEX
I
——y
y
) yy
2009 TL