Acura TL 2014 Owner's Manual

Û
Ý
ÛÝ
ÛÝ
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. While ‘‘KEYLESS ACCESS SETUP’’
is shown, press the SEL/RESET
button to enter the customize mode. KEYLESS ACCESS BEEP KEYLESS ACCESS
LIGHT FLASH DOOR UNLOCK MODE
There are three custom settings for
the keyless access setup:
CONT INUED
On models with keyless access system
K eyless A ccess Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
115
Seepage116.
Seepage117.
Seepage118.
: Press the SEL/RESET button.
: Press the INFO button ( / ).
12/07/20 10:44:21 31TK4640_120

Û
Ý Û
Ý Press the SEL/RESET button to see
the selections. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /
) button repeatedly. Select DRIVER DOOR or ALL
DOORS by pressing the INFO ( /
) button, then enter your selection
by pressing the SEL/RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘DOOR
UNLOCK MODE’’ and repeat the
procedure again.
Door Unlock Mode
Multi-Inf ormation Display
116
12/07/20 10:44:28 31TK4640_121

ÛÝ
Û
Ý Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some exterior
lights blink twice when you unlock
thedoorsbygrabbingthedriver’s
door handle while carrying the
remote.
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /) button repeatedly.
The same exterior lights blink once
when you lock the doors by pushing
the door lock button while carrying
the remote.
Keyless Access Light Flash
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
117
12/07/20 10:44:35 31TK4640_122

Û
Ý
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen. When KEYLESS ACCESS BEEP is
set to ON, the beeper sounds twice
when you unlock the doors by
grabbing the drivers door handle
while carrying the remote.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS ACCESS LIGHT
FLASH’’ and repeat the procedure
again. You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /
) button repeatedly.
When you lock the doors by pushing
the door lock button while carrying
the remote, the beeper sounds once.
Keyless Access Beep
Multi-Inf ormation Display
118
12/07/20 10:44:42 31TK4640_123

ÛÝ
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS ACCESS BEEP’’ and
repeat the procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
119
12/07/20 10:44:47 31TK4640_124

Û
Ý
ÛÝ
ÛÝ
INTERIOR LIGHT
DIMMING TIME
HEADLIGHT AUTO OFF TIMER
While ‘‘LIGHTING SETUP’’ is
shown, press the SEL/RESET
button to enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. Here are the three custom settings
f or the lighting setup:
AUTO LIGHT SENSITIVITY
Lighting Setup
Multi-Inf ormation Display
120
: Press the SEL/RESET button.
: Press the INFO button ( / ). Seepage121.
Seepage122.
Seepage123.
12/07/20 10:44:54 31TK4640_125

Û
Ý ÛÝ
Interior Light Dimming Time
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘INTERIOR LIGHT DIMMING
TIME’’ and repeat the procedure
again.
The interior lights f ade out when you
close all doors. To change how long
thelightsstayonbeforetheyfade
out, f ollow these instructions:
You can choose this item to
customize f rom ‘‘LIGHTING
SETUP’’ by pressing the INFO ( /
) button repeatedly. Select the desired setting (15sec,
30sec, or 60sec) by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
121
12/07/20 10:45:02 31TK4640_126

Û
Ý
ÛÝ
Headlight Auto Of f Timer
You can choose this item to
customize f rom ‘‘LIGHTING
SETUP’’ by pressing the INFO ( /) button repeatedly. Press the SEL/RESET button to see
the selections.
The headlights, parking lights, side
marker lights, taillights, and license
plate lights go of f af ter the selected
time when you remove the key f rom
the ignition switch and close the
driver’s door. On models with
keyless access system, the lights go
of f af ter the selected time when you
close the driver’s door and take the
remote with you. To change how
longthelightsstayonbeforetheygo
of f , f ollow these instructions:
Select the desired setting (60 sec, 30
sec, 15 sec or 0 sec) by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
Multi-Inf ormation Display
122
12/07/20 10:45:09 31TK4640_127

µµ
µ µ
µ Û
Ý
Auto Light Sensitivity
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘HEADLIGHT AUTO OFF TIMER’’
and repeat the procedure again. The headlights automatically come
on when the headlight switch is in
the AUTO position and the ambient
light reaches a changeable level. You
can select the auto light sensitivity
f rom the f ollowing f ive levels:
MAX
Theheadlightscomeonwhenitis
bright.
HIGH
Theheadlightscomeonwhenitis
somewhat bright.
MID
Theheadlightscomeonwhenitisas
bright as sunset or sunrise.
LOW
Theheadlightscomeonwhenitis
somewhat dark.
MIN
Theheadlightscomeonwhenitis
dark.
You can choose this item to
customize f rom ‘‘LIGHTING
SETUP’’ by pressing the INFO ( /
) button repeatedly.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
123
12/07/20 10:45:18 31TK4640_128

ÛÝWhen your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customizable item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
LIGHT SENSITIVITY’’ and repeat
the procedure again.
Press the SEL/RESET button to see
the selections.
Select the desired setting (MAX,
HIGH, MID, LOW or MIN) by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
124
12/07/20 10:45:23 31TK4640_129