key Acura TL 2014 Owner's Manual

µIf you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
rpm below the red zone. This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal and pressing the release
button does not work.
Set the parking brake.
Remove the key from the ignition
switch.
Remove the built-in key from the
keyless access remote (see page ).
With the shift lever in D or S, you
canalsousethepaddleshiftersto
shif t the transmission up or down.
With the paddle shifters, you can
operate the transmission much like a
manual transmission without a
clutch pedal. For more inf ormation
on driving with the paddle shif ters,
see page . The engine may cut in and out in R
position or depending on the road
condition, even when the engine
speed is lower than the tachometer’s
red zone. This is the engine’s
computer working to protect the
transmission.
To shift into the S
position, press the release button on
the front of the shift lever, and move
the lever to S. This position is similar
to D, except only gears f rom f irst to
fifth are selected. (When shifting up
automatically, the vehicle speed is
higher than when in the D position.)
The S position keeps the
transmission f rom cycling between
fourth, fifth and sixth gears in stop-
and-go driving. 1.
2.
501 201
CONT INUED
On models without keyless access
system
On models with keyless accesssystem
Shif t L ock Release
Engine Speed L imiter
S Position (S)
Automatic Transmission
Driving
497
12/07/20 11:34:42 31TK4640_502

Put a cloth on the edge of the shif t
lock release slot cover to prevent
scratches. Use a small f lat-tip
screwdriver or metal f ingernail f ile
to caref ully pry up the edge of the
cover and remove it from the slot.Insert a key or built-in key in the
shif t lock release slot.
Push down on the key or built-in
key while you press the release
buttonontheshiftleverandmove
the shift lever out of Park to
neutral.Remove the key or built-in key
from the shift lock release slot,
then reinstall the cover. Make
sure the notch on the cover is on
the rear side. Press the brake
pedal, and restart the engine.
If you need to use the shif t lock
release, it means your vehicle is
developing a problem. Have it
checked by your dealer.
3. 6.
5. 4.
Automatic Transmission
498
SHIFT LOCK
RELEASE SLOT
Vehicle without keyless access system
is shown.
COVER
12/07/20 11:34:49 31TK4640_503

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly, or
your vehicle may roll if it is parked
on an incline.
If your vehicle has an automatic
transmission, set the parking brake
bef ore you put the transmission in
Park. This keeps the vehicle f rom
moving and putting pressure on the
parking mechanism in the
transmission.Make sure the moonroof and the
windows are closed.
Turn of f the lights.
Place any packages, valuables, etc.,
in the trunk or take them with you.
Lock the doors.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire. Check the indicator on the
instrument panel to verif y that the
security system is set.
If the vehicle is f acing uphill, turn
the front wheels away from the
curb. If your vehicle has a manual
transmission, put it in f irst gear.If the vehicle is f acing downhill,
turn the front wheels toward the
curb. If your vehicle has a manual
transmission, put it in reverse gear.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
If you are unable to stop the
engine normally when the vehicle is
parked(intheParkpositiononthe
automatic transmission models), see on page
.192
On models with keyless access system
Parking T ips
Emergency Engine Stop
Parking
506
NOTE:
12/07/20 11:35:46 31TK4640_511

The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle turns
more or less than desired. It also
assists you in maintaining traction
while accelerating on loose or
slippery road surf aces. It does this
by regulating the engine’s output,
and by selectively applying the
brakes.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.When VSA is off, the VSA OFF
indicator comes on as a reminder.
When VSA activates, you will see the
VSA system indicator blink.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. There may also
be some noise f rom the VSA
hydraulic system. You will also see
the VSA system indicator blink. The main f unction of the
VSA system is generally known as
Electronic Stability Control (ESC).
The system also includes a traction
control f unction.
If this indicator comes on while
driving, you will also see a ‘‘CHECK
VSA SYSTEM’’ and/or ‘‘CHECK
HILL START ASSIST SYSTEM’’
message on the multi-inf ormation
display. Drive cautiously as the VSA
may not be f unctioning. Without
VSA, your vehicle will have normal
braking and cornering ability, but it
will not have VSA traction and
stability enhancement. Also, the VSA
OFF switch will not operate. Pull to
the side of the road when it is saf e,
and turn of f the engine. Reset the
system by restarting the engine. If
the VSA system indicator stays on, have the VSA system inspected by
your dealer.
If there is a problem with the hill
start assist system, the VSA system
indicator comes on and stays on. The
multi-inf ormation display shows a
‘‘CHECK HILL START ASSIST
SYSTEM’’ message.
With the VSA system indicator on,
you may not be able to stop the
engine even if you park the vehicle
saf ely. To stop the engine, see
on page
.192
On models with SH-AWD
On models with keyless access system
Vehicle Stability Assist
(VSA ) System Indicator VSA OFF Indicator
Emergency Engine Stop
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
510
NOTE:
12/07/20 11:36:14 31TK4640_515

Î Each tire pressure is shown in PSI
(U.S. models) or in kPa (Canadian
models).If any of the tires has low pressure,
thetirepressuremonitoralsoshows
the above message and each tire
pressure to warn you about the low
tire pressure when you select the
displaybypressingtheINFObutton
several times.
Each tire has its own pressure
sensor (not including the spare tire).
If the air pressure of a tire becomes
signif icantly low, the sensor in that
tire immediately sends a signal that
causes the low tire pressure/TPMS
indicator in the instrument panel to
come on. If this happens, you will see
which tire is losing pressure on the
multi-inf ormation display along with
a ‘‘CHECK TIRE PRESSURE’’
message.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
:
184 187
Tire Pressure Monitoring System (TPMS)
516
Canadian model
Canada
This shows that the front left tire is
losing pressure. U.S. model
Example: Technology Package is
shown.
12/07/20 11:36:57 31TK4640_521

ÎÎ
Î
To turn the system off, press and
hold the BSI OFF button when the
ignition switch is in the ON (II)
position. The BSI indicator on the
instrument panel glows amber,
indicating that the system is turned
of f . The multi-inf ormation display
indicates that the system is of f . To turn the system on again, press
and hold the same button. The BSI
indicator on the instrument panel
turns off. The multi-information
display indicates that the system is
on.
When the ignition switch is turned
to the ON (II) position, the system
will be in the previously selected ON
or OFF setting. Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
:
184 187
Blind Spot Inf ormation System (BSI)
BSI OFF Button
Driving
525
U.S. model is shown. Canadian model is shown.
12/07/20 11:37:59 31TK4640_530

µ
Î
Î
Î
Î
Multi-Inf ormationDisplay Message BSI Indicator
System
Status
ON
OFF
ON/OFF OFF Description
2
When you press and hold the BSI OFF button with the ignition switch in the ON (II) position, a
BSI ON or OFF message is displayed on the multi-information display for about 5 seconds.
The BSI indicator will remain on while the system is off.
The BSI alert indicator illuminates or flashes according to the system status.
A chime sounds to indicate that the system has been turned ON or OFF.
1: ON mode on models with keyless access system (see pages 184 and 187).
If while driving, mud, snow, or ice accumulates in the vicinity of sensor: The system may shut down
The BSI indicator illuminates, a message is displayed on the multi-information display, and a
chime sounds.
The BSI indicator will turn off and the system will return to normal once the obstacle is removed,
and you begin to drive.
Always keep the area around the radar sensors clean. BSI may not operate properly if the sensors
are obstructed.
The BSI alert indicator: May come on when a vehicle enters one of the alert zones, even if this message is displayed.
May not come on due to obstruction (splashes, etc.) even if this message is not displayed.
2: System status may remain on even when the BLIND SPOT NOT AVAILABLE message is displayed.
If the system is faulty, the BSI indicator illuminates and a message is displayed on the multi-
information display.
Have your vehicle inspected by your Acura dealer.1
Blind Spot Inf ormation System (BSI)
BSI Status Displays
526
12/07/20 11:38:08 31TK4640_531

Î
Î
CONT INUED
Your vehicle displays engine oil lif e
and maintenance service items on
the multi-information display to show
youwhenyoushouldhaveyour
dealer perf orm engine oil
replacement and indicated
maintenance service.To see the current engine oil lif e
displayed on the multi-inf ormation
display, turn the ignition switch to
the ON (II) position, and press the
SEL/RESET button on the steering
wheel repeatedly until the engine oil
lif e is displayed. Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
Based on the engine operating
conditions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e and displays it as a
percentage. :
184 187
Maintenance Minder
Engine Oil L if e Display
Maint enance
531
REMAINING ENGINE OIL LIFE
U.S. model is shown.
TM
12/07/20 11:38:38 31TK4640_536

ÛÝ
Î
Î
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ µ
µ
Pressing either INFO button ( / )
switches the display f rom the
message to another display. Once
you switch the display, this message
will go of f .
Along with the message, the system
message indicator comes on (see
page ).
When the remaining engine oil lif e is
15 to 6 percent, the multi-inf ormation
display shows a ‘‘SERVICE DUE
SOON’’ message along with the
maintenance item code(s) indicating
themainandsubitemsrequiredat
thetimeof theoilchange.Referto
page f or a complete list of the
maintenance main items and sub
items.
The remaining engine oil lif e is
shown on the multi-inf ormation
display according to this table:
The message appears on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position.Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand .
72
:
540 184 187
Calculated Engine Oil Lif e (%)
100% 91% 90% 81%
80% 71%
70% 61%
60% 51%
50% 41%
40% 31%
30% 21%
20% 16%
15% 11%10% 6% 5% 1% 0% Displayed
Engine Oil Lif e (%) 100%90%
80%
70%
60%
50%
40%
30%
20%
15%
10%5%
0%
Maintenance Minder
532
MAINTENANCE MAIN ITEM CODE
MAINTENANCE SUB ITEM CODE(S)
TM
12/07/20 11:38:45 31TK4640_537

Î
ÛÝ
Î
CONT INUED
Press the SEL/RESET button on the
steering wheel repeatedly to select
the engine oil lif e. The message
‘‘SERVICE,’’ along with ‘‘0%,’’ and the
maintenance item code are displayed
on the multi-information display
when the calculated engine oil lif e is
0to1percent.
These messages will come on every
time you turn the ignition switch to
the ON (II) position.
If the indicated required service is
not done and the remaining engine
oil lif e becomes 0%, the multi-
inf ormation display will show a
‘‘SERVICE PAST DUE’’ message,
the total distance traveled after the
remaining oil lif e became 0%, and the
maintenance item code(s).
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
Pressing either INFO button ( / )
switches the display f rom the
message to another display. To see
the message again, press either
INFO button repeatedly. Immediately have the service
perf ormed, and make sure to reset
the display as described on page . :
184 187 537
Maintenance Minder
Maint enance
535
U.S.TOTAL PAST DUE DISTANCE
TRAVELED
MAINTENANCE CODES
Canada
TM
12/07/20 11:39:05 31TK4640_540