lock Acura TSX 2004 Manual PDF

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Lower the wiper arm down against
the windshield. Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the passenger’s side f irst,
then the driver’s side.
3. 4. 5.
6.
7.
Wiper Blades
Maint enance268
BLADE BLADE
REINFORCEMENT

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on page
.)
Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently.
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. 334
A ir Condit ioning Syst em
Maint enance269
AIR CONDITIONING CONDENSER
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely.
Turn on the headlights to test the
new bulb.
On the driver’s side, reinstall the
air intake cover. Reinstall the
three fasteners and secure them
by pushing on the heads until they
lock.
3.
4.
5.
2. 1.
7.
8.
Lights
Maint enance
Replacing a Front T urn Signal
Light Bulb
284
SOCKET

Pull the inner f ender cover back.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
4. 5.
2.
1.
3.
CONT INUED
Lights
Maint enance
Replacing a Front Parking L ight
Bulb
285
HOLDING CLIPS

Pull the bulb straight out of its
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Push the new bulb straight into
the socket until it bottoms.
Put the inner f ender cover in place.
Install the holding clips. Lock each
oneinplacebypushingonthe
center.
Remove the light assembly cover
by pulling its outside edge.Remove the socket f or that bulb
by turning it one-quarter turn
counterclockwise.
Turn on the parking lights to
make sure the new bulb works.
Open the trunk.
Determine which of the three
bulbs is burned out: brake/
taillight turn signal light or side
marker light.
1.
3.
2.
6.
7.
8.
4.
Replacing Rear Bulbs
(in Fenders)
Lights
Maint enance286
COVER

Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Install the light assembly cover.
Make sure it snaps into place.To replace a bulb on the lef t side,
remove the screws in the center of
each of the two f asteners. On the
right side, remove the screw of the
f astener.
Pull the lining back caref ully.
Turn on the lights to make sure
the new bulb is working.
Open the trunk. Determine which of the two bulbs
is burned out: taillight or back-up
light.
1.
2.
5.
6.
7.
4.
3.
CONT INUED
Replacing Rear Bulbs
(in T runk L id)
Lights
Maint enance287

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to make sure
the new bulb is working.Reinstall the trunk lid trim. Make
sure it is installed under the edge
of the trunk lid seal.
Put each trim clip in the hole on
the trunk lid trim and push on the
center until it locks (the center is
flushwiththehead).
Each outside mirror has side turn
signal lights. The lights should be
replaced by your Acura dealer.
5.
6.
7.
8. 9.
10. Side T urn Signal L ight
Lights
Maint enance288

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket. Make sure the new
bulb is working.The license plate has two lights
above it. The bulbs should be
replaced by your Acura dealer.
1. 2.
3. Replacing a High-mount Brake
Light Bulb Rear L icense Plate Bulb
Lights
Maint enance289

Block the rear wheels.
Fill the f uel tank.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc. are
completely dry.
If you need to park your car f or an
extended period (more than one
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your car back on the road. If
possible, store your car indoors.
If the car is to be stored for a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the car is being stored indoors).
Disconnect the battery.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a car
body wax to the painted surf aces
that mate with the door and trunk
seals.
Change the engine oil and f ilter
(see page ).
Leave the parking brake off. Put
the transmission in Reverse
(manual) or Park (automatic). Coverthecarwitha‘‘breathable’’
cover, one made f rom a porous
material such as cotton.
Nonporous materials, such as
plastic sheeting, trap moisture,
which can damage the paint.
If possible, run the engine f or a
while periodically (pref erably once
amonth).
If you store your car f or 12 months
or longer, have your Acura dealer
perf orm the inspections called f or in
the 24 months maintenance schedule
(Normal Conditions) as soon as you
take it out of storage (see page ).
The replacements called f or in the
maintenance schedule are not
needed unless the car has actually
reached that time or mileage.
246
234
St oring Your Car
Maint enance293

If you have a f lat tire while driving,
stop in a saf e place to change it.
Stopping in traf f ic or on the shoulder
of a busy road is dangerous. Drive
slowly along the shoulder until you
gettoanexitoranareatostopthat
is far away from the traffic lanes.Park the car on f irm, level and
non-slippery ground away f rom
traffic. Put the transmission in
Park (automatic) or Reverse
(manual). Apply the parking brake.
Turn on the hazard warning lights,
and turn the ignition switch to
LOCK (0). Have all the
passengers get out of the car while
you change the tire.
2. 1.
CONT INUED
Changing a Flat T ire
T aking Care of t he Unexpect ed305
TRUNK FLOOR
JACK TOOLS
TOOL TRAY
The car can easily roll off the
jack, seriously injuring anyone
underneath.
Follow the directions for
changing a tire exactly, and
never get under the car when it
is supported only by the jack.