drain bolt Acura TSX 2004 Owner's Manual

CONT INUED
Open the hood and remove the
engine oil f ill cap.Remove the oil drain bolt and
washer from the bottom of the
engine. Drain the oil into an
appropriate container.
Install a new oil f ilter according to
instructions that come with it. Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available f rom your Acura
dealer) is required to remove the
f ilter.
Remove the bolt with a wrench,
then remove the maintenance
cover under the vehicle.
3.
2.
4.
5.
6.
Engine Oil
Maint enance247
OIL FILTER
OIL DRAIN BOLT
WASHER
BOLT
COVER

Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:
Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.Let the engine run f or several
minutes, then check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.
Install the maintenance cover and
tighten the bolt securely.
7.
8.
9. 10.
11.
12.
Maint enance
Engine Oil
248
33 lbf·ft (45 N·m , 4.6 kgf·m)
4.4 US qt (4.2
) Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Drain the coolant
into an appropriate container.Remove the two reserve tank
mounting bolts with a wrench.
Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant into an
appropriate container, then put the
tank back in its holder. Install the
mounting bolts securely.When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
3. 4.
5.6.
Cooling Syst em
Maint enance252
HOLDER
RESERVE TANK
DRAIN PLUG MOUNTING BOLTS

To thoroughly f lush the transmission,
the technician should drain and ref ill
it with Honda ATF-Z1, then drive the
vehicle a short distance. Do this
three times. Then drain and ref ill the
transmission a f inal time.Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
Make sure the notch fits in the
dipstick guide and the dipstick is
down all the way.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If you are not sure how to add f luid,
contact your Acura dealer. Remove the check bolt and look for
transmission f luid coming out of the
bolt hole. If a small amount of f luid
drips out of the bolt hole, reinstall
the check bolt.
Check the f luid level with the
transmission at normal operating
temperature and the car sitting on
level ground.
To check the transmission f luid level,
remove the two bolts, then pull down
the lef t part of the under cover.
6.
CONT INUED
T ransmission Fluid
Maint enance
6-speed Manual Transmission
257
BOLT
BOLT UNDER COVER CHECK BOLT

Pour the f luid to the f iller hole slowly
and caref ully so you do not spill.
Clean up any spills immediately.
Spilled f luid could damage
components in the engine
compartment.
If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stiffer shifting. Replace as
soon as it is convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.If you are not sure how to check and
add f luid, contact your Acura dealer.
If no f luid comes out, remove the
f iller bolt. Slowly add Honda Manual
Transmission Fluid (MTF) until it
starts to run out of the check bolt
hole. Let the f luid run out until it
stops, then reinstall the check bolt
and the f iller bolt.
Af ter checking and adding the f luid,
put the under cover back in place
and tighten the bolts securely.
T ransmission Fluid
Maint enance258
FILLER BOLT