door lock Acura TSX 2006 User Guide

The multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.
There are three types of messages;
normal display messages, engine oil
lif e and maintenance messages, and
system messages.
You can also customize some vehicle
control settings to your liking with
the multi-inf ormation display and the
two buttons on the steering wheel
(see page ).When you unlock and open the
driver’s door with the remote
transmitter, the display shows
‘‘Welcome DRIVER 1’’ or ‘‘Welcome
DRIVER 2’’ depending on which
remote transmitter you use. The
driver’s ‘‘ID’’ is detected by the
transmitter. For more information
about driver’s ‘‘ID’’, see page .If you use the key to unlock the
driver’s door, the display only shows
‘‘Welcome.’’ This means the system
cannot recognize either ‘‘DRIVER 1’’
or ‘‘DRIVER 2.’’ In this case, you
cannot use the customize settings in
the multi-information display (see
page ).
When you turn the ignition switch to
the ACCESSORY (I) position, the
display shows ‘‘Goodbye.’’
85
131
85
CONT INUED
Normal Display Messages
Multi-Inf ormation Display
Inst rument s and Cont rols
69
——y
y
(yy

If you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door, you will see
‘‘REMOVE KEY’’ in the display and
hear a reminder beeper.If the brake f luid level is at or below
theMINmarkonthesideof the
brake f luid reservoir in the engine
compartment, you will see ‘‘BRAKE
FLUID LOW.’’ If you see this
message, have the brake system
checked by your dealer (see page
). If thefuelfillcapismissingornot
tightened properly, you will see
‘‘TIGHTEN FUEL CAP.’’ Make sure
the fuel cap is installed and tightened
at least one click.
288
CONT INUED
Multi-Inf ormation Display
Remove Key Brake Fluid LowTighten Fuel Cap
Inst rument s and Cont rols
79
U.S.Canada
——y
y
(yy

You can customize some vehicle
control settings f or ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separately.
To have the driver’s ID detected,
make sure you use your transmitter
to unlock the driver’s door.If you use the key to unlock the
driver’s door, the system cannot
recognize either ‘‘DRIVER 1’’ or
‘‘DRIVER 2.’’ In this case, when you
try to enter the customizing mode,
‘‘DRIVER UNKNOWN
CUSTOMIZE IMPOSSIBLE’’ will be
displayed, and you cannot customize
some of the settings.
With the ignition switch in the ON
(II) position, press and hold the
INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’
appears in the multi-inf ormation
display.
CONT INUED
Multi-Inf ormation Display
Customized Settings
Inst rument s and Cont rols
85
DRIVER’S
ID
——y

y
(yy

ÃŽ
ÃŽÃŽ
ÃŽ ÃŽ
ÃŽ
ÃŽ
LIGHTING SETUP
DOOR · WINDOW
SETUP
WIPER SETUP
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT AUT O OFF
TIMER
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURTY RELOCK
TIMER
FRONT WIPER ACTION 15 sec
30 sec
60 sec
0sec
15 sec
30 sec
60 sec
DRIVER DOOR
ALL DOORS
ON
OFF
30 sec
60 sec
90 sec
WITH VEH SPD
INTERMITTENTSee page
105
See page 107
See page 110
See page 112
See page 114
See page 116
Default setting
Multi-Inf ormation Display
:
88
——y
y
(y
y

There are three custom settings in
the Door · Window Setup:DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURITY RELOCK TIMER
While the multi-information display
shows ‘‘DOOR · WINDOW SETUP,’’
press the SEL/RESET button on the
steering wheel. Each time you press
the INFO button, the display
changesasshowninthenext
column.
To customize a setting, press the
INFO button repeatedly until you see
the setting you want to customize,
and press the SEL/RESET button.
Then f ollow the procedures
described on the f ollowing pages.
CONT INUED
Door · Window Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
109
: Press the INFO Button.
——y
y
(y

y

While the multi-information display
is showing ‘‘DOOR · WINDOW
SETUP,’’ press the SEL/RESET
buttononthesteeringwheel.The
display changes to ‘‘DOOR LOCK
MODE’’ as shown above.Press the SEL/RESET button. The
display changes as shown above.
In def ault setting, if you push the
UNLOCK button once on the remote
transmitter or turn the key clockwise
in the driver’s door lock, only the
driver’s door unlocks.
You can select whether only the
driver’s door unlocks or all the doors
unlock in ‘‘DOOR LOCK MODE.’’
Select ‘‘DRIVER DOOR’’ or ‘‘ALL
DOORS’’ by pressing the INFO
button, and enter your selection by
pressing the SEL/RESET button.
Multi-Inf ormation Display
Door L ock Mode
110
——y

y
(y

y

When your selection is successf ully
entered, you will see the above
display f or several seconds, and then
the display goes back to
‘‘CUSTOMIZE MENU.’’If you f ail to enter your selection,
you will see the above display f or
several seconds, then the display
goes back to ‘‘CUSTOMIZE MENU.’’
Repeat the setup.To exit ‘‘DOOR LOCK MODE,’’
press the INFO button until you see
‘‘EXIT,’’ then press the SEL/RESET
button. The display goes back to
‘‘CUSTOMIZE MENU.’’
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
111
——y

y
(y

y

While the multi-information display
shows ‘‘DOOR·WINDOW SETUP,’’
press the SEL/RESET button on the
steering wheel. Then press the
INFO button repeatedly until you see
‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ as shown
above.Press SEL/RESET button, then
press the INFO button.
Each time you press the INFO
button, the display changes to ‘‘ON,’’
to ‘‘OFF,’’ then to ‘‘EXIT.’’
Select ‘‘ON’’ or ‘‘OFF’’ by pressing
the INFO button, and enter your
selection by pressing the SEL/
RESET button.
When you push the LOCK button on
the remote transmitter, the doors
and the trunk are set, and some
exterior lights f lash, and a beeper
sounds when you push the LOCK
button again within 5 seconds, and
the security system has set and a
horn sounds (see page ). You
can customize the exterior lights not
to f lash and the beeper not to sound.
203
K eyless L ock A cknowledgment
Multi-Inf ormation Display
112
——y
y
(y

y

While the multi-information display
shows ‘‘DOOR·WINDOW SETUP,’’
press the SEL/RESET button on the
steering wheel. Then press the
INFO button repeatedly until you see
‘‘SECURITY RELOCK TIMER’’ as
shown above.Press the SEL/RESET button, then
press the INFO button.
Each time you press the INFO
button, the time changes f rom ‘‘30
sec,’’ to ‘‘60 sec,’’ and then to ‘‘90 sec.’’
If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock and
the security system sets.
You can change this relock time
f rom 30 seconds to 60 or 90 seconds.
Securit y Relock T imer
Multi-Inf ormation Display
114
——y
y
(y

y

µµPush down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a turn.
Turn signal
Of f
Parking and interior lights
Headlights
High beams
Flashhighbeams
Fog lights of f
Fog lights on Turning the switch
on the lef t lever to the
‘‘ ’’position turns on the parking
lights, taillights, instrument panel
lights, side-marker lights, and rear
license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.
When the light switch is in the
‘‘ ’’ or the ‘‘ ’’ position, the
Lights On indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or LOCK (0)
position.
If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
beeper when you open the driver’s
door.
1.
2.
3.
4.
5.
6.
7.
8. T urn Signal and Headlights T urn Signal
Headlights
Turn Signal, Headlights
120
——yy
(y
y