Seat Acura TSX 2006 Repair Manual

On the f ront passenger’s door, push
the master door lock switch down to
lock the all doors, and up to unlock
them.The childproof door locks are
designed to prevent children seated
in the rear f rom accidentally opening
the rear doors. Each rear door has a
lock lever near the edge. With the
lever in the LOCK position, the door
cannot be opened f rom inside
regardless of the position of the lock
tab. To open the door, pull the lock
tab up, and use the outside door
handle.
With the driver’s door open and the
key in the ignition, both master door
lock switches are disabled. You will
see a ‘‘REMOVE KEY’’ message in
the multi-information display (see
page ). If you try to lock an open
driver’s door by pushing in the lock
tab, all doors will unlock when you
close the driver’s door.
79
L ockout Prevent ion
Door L ocks, Childproof Door L ocks
Childproof Door L ocks
Inst rument s and Cont rols
129
MASTER DOOR LOCK SWITCH
Unlock
Lock Unlock
Lock
FRONT PASSENGER’S DOOR
——yy
(y
y

Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
When you open the driver’s door
after unlocking it with the remote
transmitter, you will hear a beep
(depending on the ‘‘KEYLESS
LOCK ACKNOWLEDGEMENT’’
setting see page ). The driver’s
seat move to the positions stored in
that memory location. You will hear
two beeps when the movement is
completed.
To turn it back on, repeat this
procedure. The LED will come on
for 1 second to indicate the feature
has been turned on. The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry.
You can turn off this system
activation. Press and hold the LOCK
and UNLOCK buttons at the same
time. The LED in the remote
transmitter will blink twice. Then
release the buttons. Doing this also
cancels the ‘‘MEMORY POSITION
LINK’’ setting f or that remote and
restores the default settings.
To stop the system’s automatic
adjustment, do any of these actions:
Press any button on the driver’s
door: MEMO, memory button 1 or
2.
Push any of the adjustment
switches f or the seat.
Shif t out of Park (A/T). 112
Remote Transmitter Care
Remote Transmitter
132
——yy
(y
y

To close the trunk, press down on
the trunk lid.
See page f or cargo loading and
weight limit inf ormation. Keep the
trunk lid closed at all times while
driving to avoid damaging the lid,
and to prevent exhaust gas from
getting into the interior. Seeon page . To protect items in the trunk when
you need to give the key to someone
else:
Give the person the valet key.
Youcanopenthetrunkinanyof
three ways:
Pull up on the trunk release lever
located to the lef t of the driver’s
seat.
Press and hold the trunk release
button on the remote transmitter.
If the doors are unlocked, press
thetrunkreleaseswitchonthe
trunk lid. Lockthetrunkreleaseleverwith
the master key. Also make sure
the rear seat is not f olded down
(see page ).
1.
2.
237
56 140
CONT INUED
Carbon
Monoxide Hazard
Trunk
Inst rument s and Cont rols
135
Pull
MASTER KEY
TRUNK RELEASE LEVER TRUNK RELEASE SWITCH
——yy
(y
y

As a saf ety f eature, your vehicle has
a release lever on the trunk latch so
the trunk can be opened f rom the
inside.To open the trunk, push the release
lever to the lef t.
Parents should decide if their
children should be shown how to use
this feature.
For more inf ormation about child
saf ety, see page .
To protect items in the trunk, you
can disable the trunk-release lever
on the lef t of the driver’s seat, the
trunk-release switch on the trunk lid,
andthetrunk-releasebuttononthe
remote by turning off the trunk main
switch in the glove box and locking
the glove box. Make sure the rear
seat is not f olded down.
If you need to give the key to
someone else, give them the valet
key.
41
Emergency T runk Opener
T runk Main Switch
Trunk
136
TRUNK RELEASE LEVER
——yy
(y
y

Follow these precautions whenever
you use the seat heaters:Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
Both f ront seats are equipped with
seat heaters. The passenger seat
only has heaters in the seat bottom
because of the side airbag system.
The ignition switch must be in the
ON (II) position to use the heaters.
Push the top of the switch, HI, to
rapidly heat up the seat. Af ter the
seat reaches a comfortable
temperature, select LO by pushing
the bottom of the switch. This will
keep the seat warm. In HI, the heater turns of f when the
seat gets warm, and turns back on
after the seat temperature drops.
In LO, the heater runs continuously.
It does not cycle with temperature
changes.
Seat Heaters
Inst rument s and Cont rols
137
SEAT HEATER SWITCHES
——yy
(y
y

µ
Adjusts the seat-back
angle f orward or
backward. Moves the f ront of the
seat up or down and
the rear of the seat up
or down. Moves the seat
f orward and backward.
Moving the long horizontal switch
adjusts the seat bottom in several
directions. The seat bottom adjusts
in the direction you move the switch.
The short vertical switch adjusts the
seat back angle. Raises or lowers the
seat.To change the lumbar support, move
the lever on the right side of the
seat-back forward or backward.
Keep moving the lever f orward or
backward until you f ind a suitable
position.
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position. Make
all seat adjustments bef ore you start
driving.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs.
Driver’s seat only:Driver’s seat only:
13 15
Power Seat Adjustment
Driver’s Lumbar Support
Seats
138
——yy
(y

y

See page f or important saf etyinf ormation and a warning about how toproperly position the head restraints. 15
Your vehicle has adjustable head
restraints on the f ront seats and on
the outside positions of the rear seat.
The head restraints help protect you
and your passengers f rom whiplash
and other injuries. They are most
ef f ective when you adjust them so
the back of the occupant’s head rests
against the center of the restraint. A
taller person should adjust the
restraint as high as possible. The head restraints adjust f or height.
You need both hands to adjust the
restraint. Do not attempt to adjust it
while driving. To raise it, pull upward.
To lower the restraint, push the
release button sideways, and push
the restraint down.To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button
and pull the restraint out of the seat-
back.
CONT INUED
Head Restraints
Seats
Inst rument s and Cont rols
139
RELEASE BUTTON
RELEASE BUTTON
REAR OUTSIDE POSITION
FRONT
——yy
(y
y

The back of the rear seat folds down
to give you direct access to the trunk.
Each side f olds down separately.
With only half the seat f olded, you
can still carry a passenger in the
back seat. The seat-back can be
released f rom inside the vehicle or
inside the trunk.To f old down either side of the seat-
back f rom inside the vehicle, insert
the master key in the lock on the
rear shelf . To f old down the driver’s
side, turn the key clockwise, pull
down the top of the seat-back, then
release the key. To f old down the
passenger’s side, turn the key
counterclockwise and perf orm the
same procedure.When storing cargo, you can move
therearcentershoulderbeltoutof
the way by removing the belt from
the guide.
Seats
Folding Rear Seat
140
MASTER KEY
GUIDE
CENTER SHOULDER BELT
——yy
(y
y

To release the seat-back from inside
the trunk, pull the release loop under
the trunk panel.Do not put any heavy items on the
seat-back when it is folded.
Make sure all items in the trunk, or
items extending through the opening
into the back seat, are secured.
Looseitemscanflyforwardand
cause injury if you have to brake
hard. See
on page
.
Never drive with the seat-back
f olded down and the trunk lid open.
See on
page .
Make sure that the folded seat-back
does not interf ere with the f ront
passenger’s seat-back. This will
cause the f ront passenger’s weight
sensors to work improperly (see
page ). Also check the passenger
airbag of f indicator to assure proper
operation of the passenger’s
advanced front airbag.
Make sure all rear shoulder belts are
positioned in f ront of the rear seat-
back, and the center shoulder belt is
re-positioned in the guide whenever
the seat-back is in its upright position.
Be sure there are no twists in the
center shoulder belt.
Push the seat-back down, then let go
of the release.
To lock the seat-back upright, push it
f irmly against the trunk panel. Make
sure it is latched in place by pulling
on the top of the seat. 30
236
56
Seats
Carrying Cargo
Carbon Monoxide Hazard
Inst rument s and Cont rols
141
RELEASE LOOP
——y
y
(y
y

Adjust the seat to a comfortable
position (see page ). Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position in the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Store a driving position only when
the vehicle is parked.
Your vehicle has a memory feature
f or the driver’s seat position.
Two seat positions can be stored in
separate memories. You select a
memorized position by pushing the
appropriate button or appropriate
remote transmitter (Driver 1 or
Driver 2).
This setting can be linked or
unlinked with the remote transmitter.
To customize the setting ‘‘MEMORY
POSITION LINK’’, see page .
Press and release the MEMO
button on the driver’s door. You
will hear a beep. Then, both
indicators in the memory buttons
will start to blink. Press and hold
one of the memory buttons (1 or
2) within 5 seconds af ter you press
the MEMO button. When the
system completes to store a new
driving position, you hear two
beeps. The indicator in the stored
memory button will come on.
3.
1.
2.
103
138
Storing a Driving Position in
Memory
Driving Position Memory System
142
MEMO BUTTON
INDICATORS MEMORY BUTTONS
——yy
(y
y