Settings Acura TSX 2007 Owner's Manual

The multi -information display in the
instrument panel displays various
inform ation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comfortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs for continued trouble-free
driving.
When you unlock and open the
driver’s door with the remote
transmitter, the display shows
‘‘Welcome DRIVER 1’’ or ‘‘Welcome
DRIVER 2’’ depending on which
remote transmitter you use. The
driver’s ‘‘ID’’ is detected by the
transmitter. For more information
about driver’s ‘‘ID’’, see page .If
you use the key to unlock the
driver’s door, the display only shows
‘‘Welcome.’’ This means the system
cannot recognize either ‘‘DRIVER 1’’
or ‘‘DRIVER 2.’’ In this case, you
cannot use the customized settings
on the multi-information display (see
page ).
When you turn the ignition switch to
the ACCESSORY (I) position, the
display shows ‘‘Goodbye.’’
There
are three types of messages;
normal display messages, engine oil
life and maintenance messages, and
system messages.
You can also customize some vehicle
control settings to your liking with
the multi -information display and the
two buttons on the steering wheel
(see page ). 86
13286
CONT INUED
Normal Display Messages
Multi-Inf ormation Display
Inst rument s and Cont rols
69

You can customize some vehicle
control settings for ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separate ly.
To have the driver’s ID detected,
make sure you use your transmitter
to unlock the driver’s door.
With
the ignition switch in the ON
(II) position, press and hold the
INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’
appears on the multi-info rmation
display.
If you use the key to unlock the
driver’s door, the system cannot
recognize either ‘‘DRIVER 1’’ or
‘‘DRIVER 2.’’ In this case, when you
try to enter the customizing mode,‘‘DRIVER
UNKNOWN
CUSTOMIZE IMPOSSIBLE’’ will be
displayed, and you cannot customize
some of the settings.
Refertothetableonpage tosee
what settings you can customize. 88
Customized Settings
Multi-Inf ormation Display
86
DRIVER’S
ID

To change the settings, stop the
vehicle, and make sure to set the
parking brake and put the
transmission in Park (A/T) or
neutral (M/T). If you try to enter the
customizing mode while the vehicle
is moving, the above message
appears and you cannot change the
settings. The
first customizing menu is:
DEFAULT ALL
CHANGE
SETTING
Everytimeyoupressthe INFO
button, the display cycles from
‘‘CHANGE SETTING,’’ ‘‘DEFAULT
ALL,’’ ‘‘EXIT’’ and then back to
‘‘CHANGE SETTING.’’ Press the
SEL/RESET button to enter your
selection.
If you want the settings as they were
when the vehicle left the factory,
select ‘‘DEFAULT ALL,’’ as
described on page . If
you want to change any vehicle
control settings, select ‘‘CHANGE
SETTING,’’ and follow the
instructions on page .
You can also use the select/reset
knob in the instrument panel. Turn
the knob to select a setting and press
it to enter your selection. If you do not make any changes,
select ‘‘EXIT,’’ the display returns to
normal display.
90 92
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
87
AT model MT model

ÃŽ
ÃŽÃŽ
ÃŽ
ÃŽ ÃŽ
ÃŽ
Description
Changes how long (in seconds) the interior lights
stay on after you close the doors.
Changes how long (in seconds) the exterior lights
stay on after you close the driver’s door.
Changes which doors unlock with the remote
transmitter when the button is pushed one time.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A horn will also sound
when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Changes the windshield wiper operation between
two settings when the wiper switch is in the INT
position. Customize
Setup
15 sec
30 sec
60 sec
0sec
15 sec
30 sec
60 sec
DRIVER DOOR
ALL DOORS
ON
OFF
30 sec
60 sec
90 sec
WITH VEH SPD
INTERMITTENT Page
106
108
111
113
115
117
Customize
Group
LIGHTING SETUP
(P.106)
DOOR · WINDOW
SETUP
(P.110)
WIPER SETUP
(P.117) Customize
Menu
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT AUT O OFF
TIMER
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURITY RELOCK
TIMER
FRONT WIPER ACTION
: Default setting
Multi-Inf ormation Display
Inst rument s and Cont rols
89

If you want to set the customizable
vehicle control settings to the default
setting, press the INFO button on
the steering wheel until ‘‘DEFAULT
ALL’’ is displayed.
Press the SEL/RESET button to
enter ‘‘DEFAULT ALL.’’ You can
change the display between
‘‘CANCEL,’’ ‘‘OK’’ and ‘‘EXIT’’ each
time you press the INFO button.If you want to cancel ‘‘DEFAULT
ALL,’’ press the SEL/RESET button
while ‘‘CANCEL’’ is shown. The
display goes back to ‘‘CUSTOMIZE
ENTRY.’’
To set the def ault settings, press the
INFO button until the display
changesasshownabove.Pressthe
SEL/RESET button to select
‘‘DEFAULT ALL.’’
DEFAUL T AL L
Multi-Inf ormation Display
90

While the multi-information display
is showing ‘‘CHANGE SETTING,’’
press the SEL/RESET button. The
display will start showing the initial
‘‘CUSTOMIZE GROUP.’’ Each time
you press the INFO button, the
display changes as shown in the next
column. Press the INFO button until
you see the setup you want to
customize, and press the SEL/
RESET button to enter your
selection. You can customize some of the
vehicle control settings to your
pref erence. Here are the settings
you can customize:METER SETUP
POSITION SETUP
LIGHTING SETUP
DOOR/WINDOW SETUP
WIPER SETUP
Change Setting
Multi-Inf ormation Display
92
: Press SEL/RESET Button.
: Press the INFO Button.

There are five custom settings in the
Meter Setup:LANGUAGE SELECTION
ADJUST OUTSIDE TEMP.
DISPLAY
TRIP A & AVG. FUEL RESET
with REFUEL
ELAP. TIME RESET
CONDITION
PRIMARY DISP SELECTION
While ‘‘METER SETUP’’ is displayed,
press the SEL/RESET button on the
steering wheel. Then, press the
INFO button repeatedly. Each time
you press the INFO button, the
display changes as shown.
To customize a setting, press the
INFO button repeatedly until you see
the setting you want to customize,
and press the SEL/RESET button.
Then f ollow the procedures
described on the f ollowing pages.
CONT INUED
Meter Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
93
: Press the INFO Button.

There are two custom settings in the
Lighting Setup:Press the SEL/RESET button. The
display changes as shown above.
Each time you press the INFO
button, the highlighted number
changes f rom ‘‘15 sec,’’ to ‘‘30 sec,’’
andthento‘‘60sec.’’Tomakeyour
selection, press the SEL/RESET
button.
INTERIOR LIGHT
DIMMING TIME
HEADLIGHT AUTO OFF TIMER
While the ‘‘LIGHTING SETUP’’ is
displayed, press the SEL/RESET
button on the steering wheel. Each
time you press the INFO button, the
display changes between
‘‘INTERIOR LIGHT DIMMING
TIME’’ and ‘‘HEADLIGHT AUTO
OFF TIMER.’’ To make your
selection, press the SEL/RESET
button. The interior lights f ade out when you
close all doors. You can change the
time that the interior lights fade out.
While the multi-information display
shows ‘‘LIGHTING SETUP,’’ press
the SEL/RESET button on the
steering wheel. The display changes
to ‘‘INTERIOR LIGHT DIMMING
TIME’’ as shown above.
Lighting Setup
Int erior L ight Dimming T ime
Multi-Inf ormation Display
106

There are three custom settings in
the Door · Window Setup:DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURITY RELOCK TIMER
While the multi-information display
shows ‘‘DOOR · WINDOW SETUP,’’
press the SEL/RESET button on the
steering wheel. Each time you press
the INFO button, the display
changesasshowninthenext
column.
To customize a setting, press the
INFO button repeatedly until you see
the setting you want to customize,
and press the SEL/RESET button.
Then f ollow the procedures
described on the f ollowing pages. Door · Window Setup
Multi-Inf ormation Display
110
: Press the INFO Button.

While the multi-information display
shows ‘‘DOOR·WINDOW SETUP,’’
press the SEL/RESET button on the
steering wheel. Then press the
INFO button repeatedly until you see
‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ as shown
above.Press SEL/RESET button, then
press the INFO button.
Each time you press the INFO
button, the display changes to ‘‘ON,’’
to ‘‘OFF,’’ then to ‘‘EXIT.’’
Select ‘‘ON’’ or ‘‘OFF’’ by pressing
the INFO button, and enter your
selection by pressing the SEL/
RESET button.
When you push the LOCK button on
the remote transmitter, the door and
trunk locks are set, and some of the
exterior lights f lash. If you push the
LOCK button (with the security
system set) again within 5 seconds,
the horn sounds to let you know the
security system is working. You can
customize some of the Keyless Lock
settings. You can turn of f the
acknowledgment horn, and you can
customize the settings so that the
exteriorlightstodonotflash.
CONT INUED
K eyless L ock A cknowledgment
Multi-Inf ormation Display
Inst rument s and Cont rols
113