brake light Acura TSX 2007 Owner's Manual

This section gives inf ormation about
the controls and displays that
contribute to the daily operation of
your vehicle. All the essential
controls are within easy reach............................
Control Locations .60
............................
Instrument Panel .61
..........
Instrument Panel Indicators . 62
.............................................
Gauges .68
.............
Multi-Inf ormation Display . 69
Controls Near the Steering .........................................
Wheel .119
Windshield Wipers and .....................................
Washers .120
.......
Turn Signals and Headlights . 121
.................................
Fog Lights .122
Automatic Lighting Off .......................................
Feature .122
..............
Daytime Running Lights . 122
......
Instrument Panel Brightness . 123
............................
Hazard Warning .124
...............
Rear Window Def ogger . 124
........
Steering Wheel Adjustment . 125
.............................
Keys and Locks .126
......................
Immobilizer System .127
..............................
Ignition Switch .128
....................................
Door Locks .129
................
Childproof Door Locks . 130
.....................
Remote Transmitter .131
..............................................
Trunk .135
......
Emergency Trunk Opener . 136...................
Trunk Main Switch . 136
..................................
Seat Heaters .137
...............................................
Seats .138
...........
Power Seat Adjustment . 138
.........
Driver’s Lumbar Support . 139
........................
Head Restraints .139
.....................
Folding Rear Seat .140
Driving Position Memory ........................................
System .142
...........................................
Mirrors .145
..
Adjusting the Power Mirrors . 146
..............
Power Mirror Heaters . 146
............................
Power Windows .147
.......................................
Moonroof .150
...............................
Parking Brake .151
........................................
Sun Visor .152
................................
Vanity Mirror .152
...............................
Interior Lights .153
.........
Interior Convenience Items . 155
.....................
Beverage Holders .156
........
Accessory Power Sockets . 156
.............
Console Compartment . 157
....................
Sunglasses Holder .158
..................................
Glove Box .158
Instruments and Controls
Inst rument s and Cont rols
59

The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.
Instrument Panel
Instru m ent sand Cont ro ls
61
ANTI-LOCK BRAKE
SYSTEM (ABS)
INDICATOR
HIGH
BEAM INDICATOR
VEHICLE STABILITY ASSIST (VSA)
SYSTEM INDICATOR
VSA ACTIVATION
INDICATOR
LIGHTS
ON INDICATOR
MULTI-INFORMATION
DISPLAY
LOW FUEL
INDICATOR
CHARGING
SYSTEM
INDICATOR
CRUISE MAIN
INDICATOR SUPPLEMENTAL
RESTRAINT
SYSTEM (SRS) INDICATOR
(P.64)
(P.66)
(P.66) (P.66)(P.65)
(P.66)
IMMOBILIZER
SYSTEM INDICATOR
FOG LIGHT INDICATOR
SECURITY SYSTEM
INDICATOR (P.67)
(P.69)
SYSTEM MESSAGE
INDICATOR
SEAT BELT REMINDER
INDICATOR
(P.66)
LOW
TIRE
PRESSURE
INDICATOR
(P.19, 62)
(P.32,
64)
(P.63)
(P.64)
(P.32,
63)
PARKING BRAKE AND BRAKE
SYSTEM INDICATOR
SIDE AIRBAG OFF INDICATOR
MALFUNCTION INDICATOR LAMP
LOW OIL PRESSURE INDICATOR (P.65,
255)
(P.63, 334)
(P.62, 332)
(P.67, 257)
(P.62, 332)
(P.62, 331)

This indicator has two functions:
Itcomesonwhenyouturnthe
ignition switch to the ON (II)
position. It is a reminder to check
the parking brake. Driving with
the parking brake not fully
released can damage the rear
brakes, axles, and tires. If
it stays on after you have fully
released the parking brake while
the engine is running, or if it
comes on while driving, it can
indicate a problem in the brake
system. You will also see a
‘‘BRAKE FLUID LOW’’ or
‘‘CHECK BRAKE SYSTEM’’
message on the multi-information
display (see pages , ). For
more information, see page .
If you drive without releasing the
parking brake, a beeper will sound,
and you will also see a ‘‘RELEASE
PARKING BRAKE’’ message on
the multi-information display (see
page ). This
indicator comes on for several
seconds when you turn the ignition
switch to the ON (II) position. If it
comes on at any other time, it
indicates a poten tial problem with
your front airbags. This indicator will
also alert you to a potential problem
with your side airbags, passenger’s
side airbag automatic cutoff system,
automatic seat belt tensioners, side
curtain airbags, driver’s seat position
sensor, or the front passenger’s
weight sensors. You will also see a
‘‘CHECK AIRBAG SYSTEM’’
message on the multi-information
display (see page ). For more
info rmation, see page .
This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. If you turn the
ignition switch to the ACCESSORY
(I) or the LOCK (0) position without
turning of f the light switch, this
indicator will remain on. A reminder
chime will also sound when you open
the driver’s door and remove the key
from the ignition switch.
1.
2.
78 79
32
84
334
83
Instrument Panel Indicators
Parking Brake and Brake System
Indicator Supplemental Restraint
System (SRS) Indicator
Lights On Indicator
Inst rument s and Cont rols
63
U.S. Canada

µ To switch from low
beams to high beams, push the left
lever forward until you hear a click.
The high beam indicator will come
on (see page ). Pull it back to
return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beams will stay on as long as you
hold the lever back.
Turn the fog lights on and off by
turning the switch next to the
headlight switch.
You can use the fog lights only when
the headlights are on low beam.
They will go off when you turn the
headlights off or onto high beam. This
feature turns off the headlights,
parking lights, taillights, and license
plate lights within 15 seconds of
removing the key from the ignition
switch and closing the driver’s door.
You can change this 15 second timer
to 0, 30, or 60 seconds (see page ). With the headlight switch in the off
or position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
This feature activates if you leave
the headlight switch in the or
position, remove the key, then
open and close the driver’s door.
If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door,
the lights will turn of f af ter 10
minutes. The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights-on
reminder chime.
66
108
Automatic Lighting Of f Feature
High Beams
Fog Lights (Canadian Models) Daytime Running L ights
Headlights, Automatic Lighting Of f Feature, Daytime Running Lights
122

If you drive without releasing the
parking brake, a beeper will sound,
and you will also see a ‘‘RELEASE
PARKING BRAKE’’ message on the
multi-info rmation display (see page
).
To apply the parking brake, pull the
lever up fully. To release it, pull up
slightly, push the button, and lower
the lever. The parking brake
indicator on the instrument panel
should go out when the parking
brake is fully released (see page ).78
63
Parking Brake
Inst rument s and Cont rols
151
Driving the vehicle with the parking
brake applied can damage the rear
brakes and hubs. A beeper will sound if
the vehicle is put into gear with the
parking brake on.

Push on the accelerator pedal.
Accelerate to the desired cruising
speed and press the SET/DECEL
button.
To increase the speed in very
small amounts, tap the RES/
ACCEL button. Each time you do
this, your vehicle will speed up
about 1 mph (1.6 km/h).
You can decrease the set cruising
speed in any of these ways: Press and hold the SET/DECEL
button. Release the button when
you reach the desired speed.
To slow down in very small
amounts, tap the SET/DECEL
button repeatedly. Each time you
do this, your vehicle will slow
down about 1 mph (1.6 km/h).
Cruise control may not hold the set
speed when you are going up and
down hills. If your speed increases
going down a hill, use the brakes to
slow down. This will cancel cruise
control. To resume the set speed,
press the RES/ACCEL button. The
‘‘CRUISE CONTROL’’ message on
the multi-information display will
come back on.
You can increase the set cruising
speed in any of these ways:
Press and hold the RES/ACCEL
button. When you reach the
desired cruising speed, release the
button. Tap the brake or clutch pedal
lightly with your f oot. The
‘‘CRUISE CONTROL’’ message on
the multi-information display goes
out. When the vehicle slows to the
desired speed, press the SET/
DECEL button.
Even with cruise control turned on,
you can still use the accelerator
pedal to speed up f or passing. Af ter
completing the pass, take your foot
of f the accelerator pedal. The vehicle
will return to the set cruising speed.
Resting your f oot on the brake or
clutch pedal causes cruise control to
cancel.
Cruise Control
Changing the Set Speed
Features
205

Stop filling the tank after the fuel
nozzle automatically clicks off. Do
not try to ‘‘top off’’ the tank. Leave
some room for the fuel to expand
with temperature changes.
even though the tank is not full,
there may be a problem with your
vehicle’s fuel vapor recovery
system. The system helps keep
fuel vapor from going into the
atmosphere. Try filling at another
pump. If this does not fix the
problem, consult your dealer. To Open the Hood:
Park the vehicle, and set the
parking brake. Pull the hood
release handle located under the
lower left corner of the dashboard.
The hood will pop up slightly.
Push
the fuel fill door closed until
it latches.
Screw
the fuel fill cap back on
until it clicks at least once. If you
do not properly tighten the cap,
the malf unction indicator lamp
maycomeon(seepage ).You
will also see a ‘‘TIGHTEN FUEL
CAP’’ message on the multi-
inf ormation display.
1.
6.
4.
5.
332
If the f uel nozzle keeps clicking of f
Service Station Procedure
Opening and Closing the Hood
232
HOOD RELEASE HANDLE

Before installing any accessory:
Make sure the accessory does not
obscure any lights, or interfere
with proper vehicle operation or
performance.
Befo re installing any electronic
accessory, have the installer
contact your dealer for assistance.
If possible, have your dealer
inspect the final installation.
Do not install accessories on the
side pillars or across the rear
windows. In these areas,
accessories may interfere with
proper operation of the side
cu rtain airbags.
Modifying
your vehicle, or installing
some non-Acura accessories, can
make your vehicle unsafe. Before
you make any modifi cations or add
anyaccessories,besuretoreadthe
following information.
Your dealer has Acura accessories
that allow you to personalize your
vehicle. These accessories have
been designed and approved for your
vehicle, and are covered by warranty.
Although non-Acura accessories may
fit on your vehicle, they may not
meet factory specifications, and
could adversely affect your vehicle’s
handling and stability. Be sure electronic accessories do
not overload electrical circuits
(see page ) or interf ere with
proper operation of your vehicle.
When properly installed, cellular
phones, alarms, two-way radios, and
low-powered audio systems should
not interf ere with your vehicle’s
computer controlled systems, such
as your airbags, anti-lock brakes, and
tire pressure monitoring system. 336
A ccessories
A ccessories and Modif ications
236
Improper accessories or
modifications can affect your
vehicle’s handling, stability, and
performance, and cause a
crash in which you can be hurt
or killed.
Follow all instructions in this
owner’s manual regarding
accessories and modifications.

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly, or
your vehicle may roll if it is parked
on an incline.
If your vehicle has an automatic
transmission, set the parking brake
bef ore you put the transmission in
Park. This keeps the vehicle f rom
moving and putting pressure on the
parking mechanism in the
transmission.
If your vehicle has a manual
transmission, put it in f irst gear.Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes. If the vehicle is f acing uphill, turn
the front wheels away from the
curb. If your vehicle has a manual
transmission, put it in f irst gear.
If the vehicle is f acing downhill,
turn the front wheels toward the
curb. If your vehicle has a manual
transmission, put it in reverse gear.
Make sure the moonroof and the
windows are closed.
Turn of f the lights.
Place any packages, valuables, etc.,
in the trunk or take them with you.
Lockthedoorswiththekeyorthe
remote transmitter.
Check the indicator on the
instrument panel to verif y that the
security system is set.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire.
Parking T ips
Parking
Driving
253

Your vehicle is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The anti-lock
brake system (ABS) helps you retain
steering control when braking very
hard.The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.All f our brakes have audible brake
wear indicators.
If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them.
Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, increases wear, and reduces
their ef f ectiveness. It also keeps
your brake lights on all the time,
conf using drivers behind you.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear. Check the brakes after driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious and alert in your driving.
Braking System
Braking System Design
Brake Wear Indicators
254