steering Acura TSX 2008 Owner's Guide

µµ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III). You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. If your vehicle has an
automatic transmission, the shif t
lever must also be in Park. If the f ront wheels are turned, the
anti-thef t lock may make it dif f icult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key. This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position.
You will hear a reminder beeper if
you leave the key in the ignition switch in the LOCK (0) or the
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper.
You will also see a ‘‘REMOVE KEY’’
message on the multi-inf ormation
display (see page ).
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.
79
LOCK (0) A CCESSORY (I)
ST A RT (III)
ON (II)
Ignition Switch
128
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.
\f—\f—
y
\f\fy
(\fy\f
y
2008 TSX

The climate control system in your
vehicle provides a comfortable
driving environment in all weather
conditions.
The standard audio system has
many f eatures. This section
describes those f eatures and how to
use them.
Your vehicle has an anti-theft audio
system that requires a code number
to enable it.
The security system helps to dis-
courage vandalism and thef t of your
vehicle................
Climate Control System .160
................
Automatic Operation .162
.......
Semi-automatic Operation .163
..........
Dual Temperature Control .167
..............
Climate Control Sensors .169
..........
Playing the AM/FM Radio .170
.....................
Adjusting the Sound .175
............
AM/FM Radio Reception .177
Playing the XM
Satellite
..........................................
Radio .179
......................
Auxiliary Input Jack .184
.................................
Playing Discs .185
.........
CD Player Error Messages .193
.....................
Protecting your CDs .194
...............................
Playing a Tape .197
.............
Steering Wheel Controls .202
.................
Radio Thef t Protection .203
..........................
Setting the Clock .204
............................
Security System .205
...............................
Cruise Control .206
HomeLink
Universal ................................
Transceiver .209
.......
Bluetooth
HandsFreeLink.213
Features
Features
159
\f—\f—
y
\f
y
(\fy\f
y
2008 TSX

Theclimatecontrolsystemhastwo
sensors. A sunlight sensor is in the
top of the dashboard, and a
temperature sensor is next to the
steering column. Do not cover the
sensors or spill any liquid on them.
Sunlight Sensor/T emperature
Sensor
Climat e Cont rol Sensors
Features
169
TEMPERATURE SENSOR
SUNLIGHT SENSOR
\f—\f—
y



y
(\fy\f
y
2008 TSX

ÛÝ´µ
´
µ
´
µ
The VOL button adjusts the volume
up ( ) or down ( ). Press the top
or bottom of the button, hold it until
the desired volume is reached, then
release it.
If youareplayingaCD,thesystem
skips to the beginning of the next
track each time you press the top
( ) of the CH button. Press the
bottom ( ) to return to the
beginning of the current track. Press
it twice to return to the previous
track. You will see the disc and track
numbers on the display.
If youareplayingatapeinthe
optional tape player, press the top
( ) of the CH button to advance to
the next selection. Press the bottom
( ) to go back to the previous
selection. The system senses a silent
period, then resumes playing.
Three controls f or the audio system
are mounted in the steering wheel
hub. These let you control basic
f unctions without removing your
hand f rom the wheel. The MODE button changes the
mode. Pressing the button
repeatedly selects FM1, FM2, AM,
CD (if a CD is loaded), or a tape (if
equipped). On models with satellite
radio system, you can also select
XM1 and XM2.
If you are listening to the radio, use
the CH button to change stations.
Each time you press the top ( ) of
the button, the system goes to the
next preset station on the band you
are listening to. Press the bottom
( ) to go back to the previous
station.
Steering Wheel Controls
202
MODE BUTTON
VOL BUTTON CH BUTTON
\f—\f—
y

y
(\fy\f\fy
2008 TSX

Accelerate to the desired cruising
speedabove25mph(40km/h).
Cruise control allows you to maintain
asetspeedabove25mph(40km/h)
without keeping your f oot on the
accelerator pedal. It should be used
f or cruising on straight, open
highways. It is not recommended f or
city driving, winding roads, slippery
roads, heavy rain, or bad weather.
Pushthecruisecontrolmaster
buttononthesteeringwheel.The
CRUISE MAIN indicator in the
instrument panel comes on.Press and release the SET/
DECELbuttononthesteering
wheel. The ‘‘CRUISE CONTROL’’
message appears on the multi-
inf ormation display to show the
system is now activated.
1.
2. 3.
Cruise Control
Using Cruise Control
206
CRUISE CONTROL MASTER BUTTON
CANCEL
BUTTON CRUISE CONTROL MESSAGE
RES/ACCEL
BUTTON
U.S. model is shown
SET/DECEL BUTTON
Improper use of the cruise
control can lead to a crash.
Use the cruise control only
when traveling on open
highways in good weather.
\f—\f—
y



y
(\fy\f

y
2008 TSX

You can cancel cruise control in any
of these ways:Tap the brake or clutch pedal.
Push the CANCEL button on the
steering wheel.
Pushthecruisecontrolmaster
button. When you push the CANCEL button,
or tap the brake or clutch pedal, the
system remembers the previously
set cruising speed. To return to that
speed, accelerate to above 25 mph
(40 km/h) then press and release
the RES/ACCEL button. The
‘‘CRUISE CONTROL’’ message on
the multi-information display comes
on, and the vehicle accelerates to the
same cruising speed as bef ore. Pressing the cruise control master
button turns the system off and
erases the previous cruising speed.
Canceling Cruise Control
Resuming the Set Speed
Cruise Control
208
\f—\f—
y

y
(\fy\f
y
2008 TSX

To operate the HFL, use the HFL
Talk and Back buttons on the left
side of the steering wheel. Below the
HFL buttons is another set of voice
control buttons f or the navigation,
climate control, and audio systems.TheHFLbuttonsareusedas
f ollows:
HFLTalk:Thisbuttonisusedbefore
you give a command, to answer
incoming calls, and to conf irm
system inf ormation.
Press and release the button, then
wait f or a beep bef ore giving a
command.
HFLBack:Thisbuttonisusedto
endacall,gobacktotheprevious
voice control command, and to
cancel an operation.
When the HFL is in use, the sound
comes through the vehicle’s f ront
audio system speakers. If the audio
system is in use while operating
either of the HFL buttons or making
a call, the HFL over-rides the audio
system. To change the volume level,
use the audio system volume knob,
or the steering wheel volume
controls.
HFL Buttons
Audio System
BluetoothHandsFreeL ink
214
HFL BACK
BUTTON
VOICE CONTROL BUTTONS HFL TALK
BUTTON
Vehicle with navigation
system is shown
\f—\f—
y

y
(\fy\f
y
2008 TSX

Î
Πε
µ µ
µ µ
Î Signal Strength Indicates the
network signal strength of the
current phone. Five bars equals
f ull strength.
ROAM Status Indicates your
phone is roaming.
Battery Level Status Indicates
the power currently remaining in
your phone’s battery. Five bars
equals f ull battery strength.
When you are operating the HFL, or
when you manually select HFL on
the multi-information display, you
will see this inf ormation on the
screen: All phones may not operate
identically, and some may cause
inconsistent operation of the HFL.
TheHFLisoperatedbytheHFL
Talk and Back buttons on the left
side of the steering wheel. The next
f ew pages provide instructions f or all
basic f eatures of the HFL.
HFL Mode Indicates when you
are dialing and receiving calls.
Phone Dialing Indicates the
number you entered or the
number of the incoming call. Some phones do not send this
inf ormation to the HFL.
:
Multi-Inf ormation Display
How to Use the HFL
BluetoothHandsFreeL ink
Features
215
NOTE:
SIGNAL
STRENGTHBATTERY LEVEL STATUS
PHONE DIALING ROAM
STATUS
HFL MODE
MESSAGE
\f—\f—
y

\fy
(\fy\f\fy
2008 TSX

You can make calls using any phone
number, or by using a name in the
HFL phonebook. You can also redial
the last number called. During a call,
theHFLallowsyoutotalkupto30
minutes af ter you remove the key
from the ignition switch.With your phone on and the
ignition in the ACCESSORY (I) or
ON (II) position, press and release
the Talk button. After the beep,
say ‘‘Call’’ or ‘‘Dial.’’ The HFL
response is, ‘‘What name or
number would you like to call/
dial?’’
Press and release the Talk button.
Af ter the beep, say the number
you want to call. For example, say
‘‘123 456 7891.’’ The HFL response
is ‘‘123 456 7891. Say call, dial, or
continue to add numbers.’’ With your phone on and the
ignition in the ACCESSORY (I) or
ON (II) position, press and release
the Talk button. After the beep,
say ‘‘Call’’ or ‘‘Dial.’’ The HFL
response is ‘‘What name or
number would you like to call/
dial?’’
Press and release the Talk button.
After the beep, say the name you
want to call. For example, say
‘‘Eric.’’ The HFL response is
‘‘Would you like to call Eric?’’
Press and release the Talk button.
Af ter the beep, say ‘‘Yes.’’ The
HFL response is ‘‘Calling’’ or
‘‘Dialing.’’ Once connected, you
will hear the person you called
through the audio speakers. To
change the volume, use the audio
system volume knob.
You can also make a call directly
from the list shown on the navigation
display.
Press and release the Talk button.
Af ter the beep, say ‘‘Call’’ or ‘‘Dial.’’
The HFL response is ‘‘Calling’’ or
‘‘Dialing.’’ Once connected, you
will hear the person you called
through the audio speakers. To
change the volume, use the audio
system volume knob, or the
steering wheel volume controls.
To end the call, press the Back
button. 1.
3.
3.
1.
2. 2.
4.
To make a call using a phone number, do this: To make a call using a name in the HFL
phonebook, do this:
On vehicles with navigation system
CONT INUED
Making a Call
BluetoothHandsFreeL ink
Features
223
\f—\f—
y
\f
y
(\fy\fy
2008 TSX

Press and release the Talk button.
Af ter the beep, say ‘‘Send.’’ The
dial tones will be sent, and the call
will continue.
Press and release the Talk button.
Af ter the beep, say ‘‘Send.’’ The
HFL response is ‘‘What name or
number would you like to send?’’
Press and release the Talk button.
After the beep, say the name you
want to send. For example, say
‘‘Account number.’’ The HFL
response is ‘‘Would you like to
send account number?’’
Press and release the Talk button.
Af ter the beep, say ‘‘Send.’’ The
dial tones will be sent, and the call
will continue.
The HFL allows you to send
numbers or names during a call. This
is usef ul when you call a menu-
driven phone system. You can also
program account numbers into the
HFL phonebook for easy retrieval
during menu-driven calls.
Press and release the Talk button.
Af ter the beep, say ‘‘Send.’’ The
HFL response is, ‘‘What name or
number would you like to send?’’
Press and release the Talk button.
Af ter the beep, say the number
you want to send. For example,
say‘‘1,2,3.’’TheHFLresponseis
‘‘1, 2, 3. Say send, or continue to
add numbers.’’
To end the call, press the Back
button.
To redial the last number called by
the phone, press and release the
Talk button. After the beep, say
‘‘Redial.’’ The HFL response is,
‘‘Redialing.’’ Once connected, you
will hear the person you called
through the audio speakers. To
change the volume, use the audio
system volume knob, or the steering
wheel volume controls. 1.
2.
1.
2. 3.
3.
4.
To send a name during a call, do this:
To send a number during a call, do this:
Sending Numbers or Names
During a Call
BluetoothHandsFreeL ink
224
\f—\f—
y

\fy
(\fy\fy
2008 TSX