light Acura TSX 2011 Advanced Technology Guide

I N S T R U M E N T P A N E L I N D I C A T O R S
O n \b O f f I n d i c a t o r sM a l f u n c t i o n I n d i c a t o r s
If an indicator remains on\b there may be a problem; see your dealer
Charging system
Low brake fluid\b Brake system
Low oil pressure
VSA(Vehicle Stability Assist)
Malfunction indicator lamp(check engine light)
TPMS (blinks)(Tire Pressure Monitoring System)
EPS(Electric Power Steering)SRS(Supplemental Restraint System)
ABS(Anti-lock Brake System)
PASSENGERAIRBAG
OFFPASSENGER AIRBAG OFF
(above audio panel)
SIDE AIRBAG OFF
VSAOFF
Immobilizer (blinks): improperly
coded key; use correct key
Headlightson
Turn signals/hazards on
CRUISE MAIN on
CRUISE CONTROL on Fog lights
onHigh beams on
Briefly appear with each engine start. Red and amber indicators are most critical.
Blue and green indicators are used for general information.
3
2
C o n d i t i o n I n d i c a t o r s
Action is needed by driver
Parking brake on:
ReleaseMessage indicator:
See MID
Door/tailgate open:
Close door or tailgateLow tire pressure (stays on):
Add air
Seat belt reminder:
Fasten seat belt(s)Low fuel:
Refill
11 TSX 5D ATG\fATG_NEW STYLE 9/9/2010 2\f51 PM Page 3

7
6
T i r e P r e s s u r e M o n i t o r i n g S y s t e m
Alerts you when one or more of your tires have significantly low pressure.
Toggle
to the tire pressure monitor display to view pressure readings on
the MID.
H o w I t W o r k s
If the tire pressure drops significantly below recommended levels:
• The low tire pressure indicator comes on.
• A "CHECK TIRE PRESSURE" message appears on the MID.
• The tire icon(s) showing low pressure blinks.
W h a t t o D o
1. Visually inspect the tires for
damage.
2. Use a tire air pressure gauge
(or check the MID) to check
which tire(s) have low pressure.
3. Inflate the tire(s)\b if necessary\b
to the recommended pressures
listed on the label on the
driver’s doorjamb.
C u s t o m i z i n g S e t t i n g s U s i n g t h e M I D
1. Select “CHG SETTING.”
3. Select “AUTO DOOR
UNLOCK.”4. Select “ALL DOORS with
SHIFT TO P.”
5. Once the setting has been saved\b select“EXIT.”
Four groups of settings can be programmed using the MID*: Meter Setup\b Position
Setup\b Lighting Setup\b and Door Setup.
SEL/RESET
button
INFO
buttons
Pressthe Info button to toggle to
the “Keyless Memory Settings”
display\b then pressSEL/RESET to
activate the menu.
M o d i f y i n g t h e A u t o D o o r U n l o c k S e t t i n g
* See Customized Settings in your owner’s manual for other programmable settings.
2. Select “DOOR SETUP.”
As the default setting\b only the driver's door unlocks when you shift to Park.
Follow the steps below to set all doors to unlock when you shift to Park:
11 TSX 5D ATG\fATG_NEW STYLE 9/9/2010 2\f53 PM Page 5

11
1\f
R E V E R S E T I L T D O O R M I R R O R
H o w I t W o r k s
When you shift into Reverse (R)\b the passenger’s outside door mirror tilts down slightly
to improve your view as you parallel park. Shifting out of Reverse returns the tilted
mirror to its original position.
• To tilt the passenger’s
door mirror\b movethe
mirror selector switch
to the right (R)
position when in
Reverse.
• To turn the feature off\b move the switch
to the middle or left
(L) position.
R E A R V I E W C A M E R A( T e c h n o l o g y P a c k a g e )
For added convenience\b the area behind your vehicle is displayed to help
you navigate while backing up.
• When you shift into Reverse\b a real-time image of the area behind your vehicle is shown in the
navigation display.
• Yellow parking guidelines also appear to help you judge distance.
• Adjust the screen brightness by turning the
Interface Dial.
• The display turns off when you shift out of Reverse.
H o w I t W o r k s
H O M E L I N K ®
Press and hold the button on the
remote and the HomeLink buttonat
the same time. Then, while
continuing to hold the HomeLink
button, press and release the button
on the remote every 2seconds.
Does the LED blink at a faster ratewithin 20
seconds?
Press and hold
the HomeLink
button again. Training
complete
YES
NO
HomeLink indicator
flashes for 2 seconds,
then remains on. HomeLink LED
remains on.YES
NO YES
NO
Position the remote transmitter you
wish to link 1–3 inches from the
HomeLink button you want to program.1
Press and hold the desired
HomeLink button and the button on
the remote transmitter.
Does the HomeLink indicator (LED) blink at a
faster rate after about 10 seconds?
2
a
The remote has a rolling code.
Pressthe “learn” button on the
remote-controlled device (e.g.,
garage door opener).
Press the programmed HomeLink
button again; the remote-controlled
device should operate. Within 30 seconds, pressand
hold the programmed HomeLink
button for 2 seconds.a
Press and hold the programmed
HomeLink button for about a
second.
Does the device (garage door opener) work?
3
b
4
5
T r a i n i n g a B u t t o n
The HomeLink Universal Transceiver built into your vehicle can be programmed to
operate up to three remote-controlled devices around your home\b such as garage
doors\b lighting\b or home security systems.
If you have any problems programming HomeLink\b see the owner’s manual
included with the device you are trying to program\b call HomeLink at
(8\f\f) 355-3515\b or visit www.homelink.com.
11 TSX 5D ATG\fATG_NEW STYLE 9/9/2010 2\f54 PM Page 7