Acura TSX 2011 Owner's Manual

Opening and Closing the Windows
100Controls
Opening/Closing the Power WindowsThe power windows can be opened and closed when the ignition switch is in ON II
, using the switches on the doors. The driver's side switch can be used to open
and close all of the windows.
The main switch on the driver's side must be switched off (not pushed in, indicator
off) to open and close the windows from anywhere other than the driver's seat.
When the main switch is turned on (pushed in, indicator on), you can only operate
the windows from the driver's seat. Turn the main switch on when children are in
the vehicle.
Opening/Closing the Power Windows
WARNING
Closing a power window on someone's
hands or fingers can cause serious injury.
Make sure your passengers are away from
the windows before closing them.
Opening/Closing Windows with Auto-Open/Close Function
The power windows can be operated for up to 10
minutes after you turn the ignition switch off.
Opening either front door cancels this function.
Auto Reverse
If a power window senses resistance when closing
automatically, it will stop closing and reverse
direction.
The driver’s window auto reverse function is
disabled when you continuously pull up the switch.
The auto reverse function stops sensing when
the window is almost closed to ensure that it fully
closes.
Automatic operation
To o p e n : Push the switch down firmly
To close: Pull the switch up firmly.
The window opens or closes completely. To
stop the window at any time, push or pull the
switch briefly. Manual operation
To open: Push the switch down lightly.
To close: Pull the switch up lightly.
Release the switch when the window reaches
the desired position.
ONOFF
Main Switch
Driver’s Window Switch
Indicator
Front Passenger’sWindow Switch

Opening and Closing the Windows
Opening/Closing the Power Windows
101
Continued
Controls
Opening/Closing Windows without Auto-Open/Close Function Opening Windows and Moonroof with the Remote
Tra n s m i t t e r
To o p e n : Press the UNLOCK button twice
within 10 seconds and hold it down for the
second time. If the windows stop midway,
repeat the procedure.
Opening Windows and Moonroof with the Remote Transmitter
You cannot operate the power windows with the
remote transmitter when the key is in the ignition
switch.
To open: Push the switch down.
To close: Pull the switch up.
Release the switch when the window reaches
the desired position.
Unlock
Button
Close
Open

Opening and Closing the Windows
Opening/Closing the Power Windows
102Controls
Opening/Closing the Windows/Moonroof with the Key
To open: Unlock the driver's door with the
key. Within 10 seconds of returning the key
to the central position, turn the key in the
unlock direction and hold it there.
To close: Lock the driver's door with the key.
Within 10 seconds of returning the key to
the central position, turn the key in the lock
direction and hold it there.
Release the key to stop the windows/
moonroof at the desired position. If you
want further adjustment, repeat the same
operation.
Opening/Closing the Windows/Moonroof with the Key
You cannot close the power windows with the key
when the door is open.
Close
Open

103
Opening and Closing the Moonroof
Controls
Opening/Closing the Moonroof
You can only operate the moonroof when the ignition switch is in ON
II
. Use the
switch in the front of the ceiling to open and close the moonroof.
Automatic operation
To open: Pull the switch back firmly, then
release.
To close: Push the switch forward firmly,
then release.
The moonroof will automatically open or
close all the way. To stop the moonroof
midway, touch the switch briefly. Manual operation
To open: Pull the switch back, and hold it
until the desired position is reached.
To close: Push the switch forward, and hold
it until the desired position is reached. Tilting the moonroof up
To tilt: Push on the center of the moonroof
switch.
To close: Push the switch forward firmly,
then release.
WARNING
Opening or closing the moonroof on
someone's hands or fingers can cause
serious injury.
Make sure all hands and fingers are clear
of the moonroof before opening or
closing it. Opening/Closing the Moonroof NOTICE Opening the moonroof in below freezing
temperature or when it is covered with snow or ice
can damage the moonroof panel or motor.
The power moonroof can be operated for up to 10
minutes after you turn the ignition switch off.
Opening either front door cancels this function.
When resistance is detected, the auto reverse
function causes the moonroof to change directions,
then stop. Auto reverse stops sensing when the
moonroof is almost closed to ensure that it fully
closes. Make sure that all objects, including fingers,
are clear of the moonroof.

Operating the Switches Around the Steering Wheel
104Controls
0 LOCK: Insert and remove the key in this
position.
I ACCESSORY: Operate the audio system and
other accessories in this position.
II ON: This is the position when driving.

III
START: This position is for starting the engine.
The switch returns to ON
II when you let go of
the key.
Ignition Switch
Ignition Switch Manual transmission models
Automatic transmission models You cannot take the key out unless the shift lever is
in
P.
All models If you open the driver's door when the key is in
LOCK
0 or ACCESSORY
I , a warning buzzer will
sound to remind you to take the key out.
When this happens, the following messages appear
on the multi-information display:
In LOCK
t
0 : "REMOVE KEY."
In ACCESSORY
t
I : "REMOVE KEY" The buzzer
will stop when you take the key out.
If the key won't turn from LOCK
0 to ACCESSORY
I, turn the key while moving the steering wheel
left and right. The steering wheel will unlock,
allowing the key to turn.
WARNING
Removing the key from the ignition switch
locks the steering. If you do this while the
vehicle is in motion, you can lose control
of the vehicle.
Only remove the key from the ignition
switch when parked.

105
Continued
Controls
Operating the Switches Around the Steering Wheel
Turn Signals
Light Switches
Turn Signals
The turn signals can be used when the
ignition switch is in ON
II
.
Rotating the light switch turns the lights on
and off, regardless of the position of the
ignition switch.
High beams
Push the lever forward until you hear a click. Low beams
When in high beams, pull the lever back to
return to low beams. Flashing the high beams
Pull the lever back, and release it.
Manual Operation
Light Switches
If you remove the key from the ignition switch while
the light is on, a chime sounds when the driver’s
door is opened.
When the lights are on, the lights on indicator in
the instrument panel will be on.
Indicators


P. 6 4
Repeatedly turning the headlights on and off
reduces the life of the HID headlight bulbs.
If you sense that the level of the headlights is
abnormal, have the vehicle inspected by a dealer.
Do not leave the lights on when the engine is off
because it will cause the battery to discharge.
Light Switches
Right Turn
Left Turn
High Beams
Low BeamsFlashing the
high beams
Turns on side marker, tail and
license plate lights Turns on headlights, parking,
side marker, tail, and license
plate lights

Operating the Switches Around the Steering Wheel
Light Switches
106Controls
Automatic Operation (automatic lighting control)
Automatic lighting control can be used when
the ignition switch is in ON
II
.
When you turn the light switch to
AUTO
,
the headlights and other exterior lights will
switch on and off automatically depending
on the ambient brightness.
Automatic Operation (automatic lighting control)
We recommend that you turn on the lights manually
when driving at night, in a dense fog, or in dark
areas such as long tunnels or parking facilities.
The light sensor is in the location shown below.
Do not cover this light sensor with anything;
otherwise, the automatic lighting system may not
work properly.Light SensorYou can change the AUTO light sensitivity and
automatic lighting off timer setting using the multi-
information display.
Customization Procedure


P. 8 0
Automatic lighting off feature
The headlights, all other exterior lights, and the instrument panel lights turn off
within 15 seconds after you remove the key and close the driver's door.
If you turn the ignition switch to LOCK
0 with the headlight switch on, but do
not open the door, the lights turn off after 10 minutes (3 minutes, if the switch is
in the
AUTO
position).
The lights turn on again when you unlock or open the driver's door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver's door, you will hear a lights on reminder chime.

Operating the Switches Around the Steering Wheel
Fog Lights
107
Controls
Fog Lights
When the low beam headlights are on, turn
the fog light switch on to use the fog lights.
Fog Lights
When the fog lights are on, the indicator in the
instrument panel will be on.
They go off when the headlights turn off, or when
the daytime running lights are on.
Indicators


P. 6 4
Daytime Running LightsThe high beam headlights and indicator come on slightly dimmer than normal.
The ignition switch is in ON t
II
.
The headlight switch is off, or in t
.
The parking brake is released. t
The lights remain on even if you set the parking brake. Turning off the ignition
switch will turn off the daytime running lights.
The high beam headlights return to the original brightness once the headlight
switch is turned on.
Fog Light Switch

Operating the Switches Around the Steering Wheel
Wipers and Washers
108Controls
Wipers and Washers
The windshield wipers and washers can be
used when the ignition switch is in ON
II
.
MIST
The wipers run at high speed until you
release the lever. Wiper switch (OFF, INT, LO, HI)
Change the wiper switch setting according to
the amount of rain. Adjusting the delay
Turn the adjustment ring to adjust the wiper
delay.
Windshield Wipers and Washers NOTICE Do not use the wipers when the windshield is dry.
The windshield will get scratched, or the rubber
blades will get damaged. NOTICE In cold weather, the blades may freeze to the
windshield, becoming stuck.
Operating the wipers in this condition may
damage the wipers. Use the defroster to warm the
windshield, then turn the wipers on.
If the vehicle speeds up while the wipers are
operating intermittently, the length of the wipe
interval shortens. When the vehicle starts moving,
the wipers make a single sweep.
The wiper operation of the shortest delay setting
(
) and the LO setting become the same when the
vehicle speeds up.
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
Long delayShort delay
Washer
Sprays while you pull the lever toward you.
When you release the lever, the wipers make
two or three more sweeps before stopping.
MIST OFF INT: Low speed with
intermittent LO: Low speed wipe HI: High speed wipe Intermittent Time
Adjustment RingPull
to use
washer.

Operating the Switches Around the Steering Wheel
Brightness Control
109
Controls
Brightness Control
When the parking lights are turned on and
the ignition switch is in ON
II
, you can
use the brightness control knob to adjust
instrument panel brightness.
Brighten: Turn the knob to the right.
Dim: Turn the knob to the left.
You will hear the beeper when the brightness
reaches minimum or maximum. The multi-
information display will return to its original
state several seconds after you adjust the
brightness.
Brightness level indicator
The brightness level is shown on the multi-
information display while you are adjusting it.
As the brightness level increases to the right,
the instrument panel gets brighter.
Brightness Control
Instrument panel brightness varies, depending
on whether the exterior lights are on or off. The
instrument panel dims to reduce glare when they
are on.
Pressing either
(information) button
switches the display.
If you turn the knob to the right until the brightness
display is up to max, the beeper sounds. This cancels
the reduced instrument panel brightness when the
parking lights are on.
The brightness can be set differently for when the
exterior lights are on, and when they are off.
Control Knob