battery Acura TSX 2011 Owner's Guide

Cleaning
Exterior Care
274Maintenance
Applying Wax
A good coat of automotive body wax helps protect your vehicle’s paint from the
elements. Wax will wear off over time and expose your vehicle’s paint to the
elements, so reapply as necessary.
Maintaining the Bumpers and Other Resin Coated Parts
If you get gasoline, oil, engine coolant, or battery fluid on resin coated parts, they
may be stained or the coating may peel. Promptly wipe it away using a soft cloth
and clean water.
Cleaning the Window
Wipe using a glass cleaner.
Maintaining Aluminum Wheels
Aluminum is susceptible to deterioration caused by salt and other road
contaminants. Use a sponge and mild detergent to wipe away promptly.
Be careful not to use harsh chemicals (including some commercial wheel cleaners)
or a stiff brush. They can damage the clear coat of the aluminum alloy wheels that
helps keep the aluminum from corroding and tarnishing.
Applying Wax NOTICE Chemical solvents and strong cleaners can damage
the paint, metal, and plastic on your vehicle. Wipe
up spills immediately. Maintaining the Bumpers and Other Resin Coated Parts
Ask a dealer about the correct coating material
when you want to repair the painted surface of the
parts made of resin. Cleaning the Window
Wires are mounted to the inside of the rear window.
Wipe along the same direction as the wires with a
soft cloth so as not to damage them.

283
Engine Does Not Start
Handling the Unexpected
Checking the EngineIf the engine does not start, turn the ignition switch to START III
and check the
starter.
Checking the Engine
If you must start the vehicle immediately, use an
assisting vehicle to jump start it.
Jump Starting


P. 2 8 4

Starter condition Checklist
Starter doesn't turn or turns
over slowly.
The battery may be dead. Check
each of the items on the right and
respond accordingly.Check brightness of the interior light.
Turn on interior lights and check brightness.
If the interior lights are dim or do not come on at all t
 Battery Inspection and Maintenance P. 2 6 8
If the interior lights come on normally t
Fuse Inspection and Replacement
P. 2 9 4
The starter turns over normally
but the engine doesn't start.
There may be a problem with the
fuse. Check each of the items on
the right and respond accordingly.Review the engine start procedure.
Follow its instructions, and try to start the engine again.
Starting the Engine P.1 9 1
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
 Immobilizer System P. 9 8
Check the fuel level.
There should be enough fuel in the tank.
Fuel Gauge P. 7 5
Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.
 Inspecting and Changing Fuses P. 2 9 7
If the problem continues:
 Emergency Towing P. 2 9 8

Jump Starting
284Handling the Unexpected
Jump Starting Procedure
Turn off the power to electric devices, such as audio and lights. Turn off the
engine, then open the hood.
Jump Starting
6-cylinder models 1. Slide out the battery terminal cover. All models 2. Connect the first jumper cable to your
vehicle's battery
terminal.
3. Connect the other end of the first jumper
cable to the assisting vehicle's
terminal.
Use a 12-volt booster battery only.
4. Connect the second jumper cable to the
assisting vehicle's
terminal.
WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.
4-cylinder models 6-cylinder models Booster Battery
Cover

285
Continued
Handling the Unexpected
Battery performance degrades in cold conditions
and may prevent the engine from starting. Jump Starting
5. Connect the other end of the second
jumper cable:
4 -cylinder models with automatic transmission

Engine mounting bolt
4 -cylinder models with manual transmission

Transmission mounting bolt
6-cylinder models

Engine hanger
Do not connect this jumper cable to any
other part of the engine.
6. If your vehicle is connected to another
vehicle, start the assisting vehicle's engine
and increase its rpm slightly.
7. Attempt to start your vehicle's engine. If
it turns over slowly, check that the jumper
cables have good metal-to-metal contact.
Jump Starting
6-cylinder models 4-cylinder models with
automatic transmission 4-cylinder models with
manual transmissionBooster Battery

286Handling the Unexpected
Jump Starting What to Do After the Engine Starts
Once your vehicle's engine has started, remove the jumper cables in the following
order.
1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jumper cable from the assisting vehicle's
battery
terminal.
3. Disconnect the jumper cable from your vehicle's battery
terminal.
4. Disconnect the other end of the jumper cable from the assisting vehicle's
battery
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
6-cylinder models

Indicator, Coming On/Blinking
290Handling the Unexpected
If the Low Oil Pressure Indicator Comes On
Reasons for the indicator to come on
Comes on when the engine oil pressure is low. What to do as soon as the indicator comes on
1. Immediately park the vehicle in a safe place.
2. If necessary, turn the hazard warning lights on. What to do after parking the vehicle
1. Stop the engine and let it sit for about one minute.
2. Open the hood and check the oil level.
Add oil as necessary.
3. Start the engine and check the low oil pressure indicator. The light goes out: Start driving again. The light does not go out within 10 seconds: Stop the engine and
contact a dealer for repairs immediately.
If the Charging System Indicator Comes On
Reasons for the indicator to come on
Comes on when the battery is not being charged. What to do when the indicator comes on
Turn the climate control system, rear defogger, and other electrical
systems, and immediately contact a dealer for repairs.
If the Low Oil Pressure Indicator Comes On NOTICE Running the engine with low oil pressure can cause
serious mechanical damage almost immediately. If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engine may rapidly discharge
the battery.

Fuses
294Handling the Unexpected
If any electrical devices are not working, turn the ignition switch to LOCK 0
and
check to see if any applicable fuse is blown.
Engine Compartment Fuse Box
Located near the brake fluid reservoir. Push the tabs to open the box.
Fuse Locations
Fuse locations are shown on the fuse box cover.
Locate the fuse in question by the fuse number and
box cover number.
Circuit protected and fuse rating
Fuse Locations
Circuit Protected Amps
1Battery100 A
*1
120 A
*2
Passenger's Side Fuse Box 40A
2EPS 70 A
Passenger's Side Fuse Box (40 A)
ABS/ VSA FSR 30 A
−−
ABS/ VSA Motor 30 A
−−
Circuit Protected Amps
3IG 50 A
Driver's Side Fuse Box (40 A)
Passenger's Side Light Main 30 A
Driver's Side Fuse Box (60 A)
Driver's Side Light Main 30 A
Main Fan Motor 30 A
−
*1
−
Wiper Motor
*2
30 A
Wiper Motor
*1
Sub Fan Motor*2
30 A
4 Rear Defogger 40 A
5Sub Fan Motor
*1
20 A
−
*2
−
6− −
7− −
8 Heater Motor 40 A
9 Hazard 15 A
Circuit Protected Amps
10 H orn 10 A
11 − −
12 St o p 15 A
13 IG Coil 15 A
14 FI Sub 15 A
15 B a c ku p 10 A
16 Interior Lights 7.5 A
17 FI Main 15 A
18 DBW 15 A
19−
*1
−
Back Up FI ECU
*2
7. 5 A
20 MG Clutch 7.5 A
21Engine Oil Level
*1
7.5 A
Fan RLY
*2
*1: 4-cylinder models
*2: 6 -cylinder models

Specifications
302Information
4-cylinder models O Vehicle SpecificationsModel Acura TSX
No. of Passengers:
Front
Rear
Tot al2
3
5
Weights:
Gross Vehicle Weight
RatingU.S.: 4,475 lbs (2,030 kg)
*1
Canada: 2,030 kg
*1
U.S.: 4,395 lbs (1,995 kg)
*2
Canada: 1,995 kg
*2
Gross Axle Weight
Rating (Front) U.S.: 2,410 lbs (1,095 kg)
*1
Canada: 1,095 kg
*1
U.S.: 2,325 lbs (1,055 kg)
*2
Canada: 1,055 kg
*2
Gross Axle Weight
Rating (Rear) U.S.: 2,090 lbs (950 kg)
Canada: 950 kg
Air Conditioning:
Refrigerant Type
Charge Quantity
Lubricant TypeH F C-13 4 a ( R -13 4 a)
15.8 – 17.6 oz (450 – 500 g)
SP-10*1: Automatic transmission models
*2: Manual transmission models
O Engine SpecificationsDisplacement 144 cu-in (2,354 cm
3)
Spark PlugsNGK ILZKR7B-11S
DENSO SXU22HCR11S
O FuelFuel:
Ty peUnleaded gasoline, Pump octane
number of 91 or higher
Fuel Tank Capacity 18.5 US gal (70 â„“)O BatteryCapacity/Type 36AH(5)/45AH(20)/47AH(20)O Washer FluidTank CapacityU.S.: 2.6 US qt (2.5 â„“)
Canada: 4.8 US qt (4.5 â„“)
O Light BulbsHeadlights (Low Beam)35W (D2S)*
3
55W (H1)*
4
Headlights (High Beam) 60W (HB3)
Fog Lights 55W (H11)
Front Turn Signal/Parking/Side
Marker Lights21/5W
Side Turn Signal Lights
(on Door Mirrors)LED
Brake/Taillights 21/5W
Rear Turn Signal Lights 21W
Back-Up Lights 21W
Rear Side Marker Lights 3CP
High-Mount Brake Light 21W
License Plate Lights 5W
Trunk Light 5W
Interior Lights
Spotlight
Ceiling Light 8W
8W
Vanity Mirror Lights 2W
Courtesy Lights 3.8W*3: Vehicle with discharge headlights
*4: Vehicle with halogen bulb low beam headlights

Specifications
304Information
6-cylinder models O Vehicle SpecificationsModel Acura TSX
No. of Passengers:
Front
Rear
Tot al2
3
5
Weights:
Gross Vehicle Weight
RatingU.S.: 4,630 lbs (2,100 kg)
Canada: 2,100 kg
Gross Axle Weight
Rating (Front) U.S.: 2,557 lbs (1,160 kg)
Canada: 1,160 kg
Gross Axle Weight
Rating (Rear) U.S.: 2,083 lbs (945 kg)
Canada: 945 kg
Air Conditioning:
Refrigerant Type
Charge Quantity
Lubricant TypeH F C-13 4 a ( R -13 4 a)
15.8 – 17.6 oz (450 – 500 g)
SP-10
O Engine SpecificationsDisplacement 212 cu-in (3,471 cm
3)
Spark PlugsNGK ILZKR7B11
DENSO SXU22HCR11
O FuelFuel:
Ty peUnleaded gasoline, Pump octane
number of 91 or higher
Fuel Tank Capacity 18.5 US gal (70 â„“)O BatteryCapacity/Type 55AH(5)/72AH(20)O Washer FluidTank CapacityU.S.: 2.6 US qt (2.5 â„“)
Canada: 4.8 US qt (4.5 â„“)
O Light BulbsHeadlights (Low Beam) 35W (D2S)
Headlights (High Beam) 60W (HB3)
Fog Lights 55W (H11)
Front Turn Signal/Parking/Side
Marker Lights21/5W
Side Turn Signal Lights
(on Door Mirrors)LED
Brake/Taillights 21/5W
Rear Turn Signal Lights 21W
Back-Up Lights 21W
Rear Side Marker Lights 3CP
High-Mount Brake Light 21W
License Plate Lights 5W
Trunk Light 5W
Interior Lights
Spotlight
Ceiling Light 8W
8W
Vanity Mirror Lights 2W
Courtesy Lights 3.8W

309
Emissions Testing
Continued
Information
Your vehicle uses "readiness codes," as part of it's onboard self diagnostic system.
Some states refer to these codes during testing to see if your vehicle's emissions
components are working properly.
The codes may not be read if you go through the testing just after the battery has
gone dead or been disconnected.
To check if they are set, turn the ignition switch to ON
II
, without starting the
engine. The malfunction indicator lamp will come on for several seconds. If it then
goes off, the readiness codes are set. If it blinks five times, the readiness codes are
not set.
If you are required to have your vehicle tested before the readiness codes are
ready, prepare the vehicle for retesting by doing the following:
1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.
3. Make sure the ambient temperature is between 40 °F and 95 °F (4 °C and 35
°C).
4. Start the engine without touching the accelerator pedal, and let it idle for 20
seconds.
5. Keep the vehicle in
P
(automatic transmission) or
N
(manual transmission).
Increase the engine speed to 2,000 rpm, and hold it there until the temperature
gauge rises to at least 1/4 of the scale (about 3 minutes).
6. Let the engine idle with your foot off the accelerator for 20 seconds.
Testing of Readiness Codes
The readiness codes are erased when the battery is
disconnected, and set again only after several days
of driving under a variety of conditions.
If a testing facility determines that the readiness
codes are not set, you may be requested to return
at a later date to complete the test.
If the testing facility determines the readiness codes
are still not set, see a dealer.
Testing of Readiness Codes