brake Acura TSX 2011 Owner's Guide

193
Driving
When Driving
Precautions While Driving
Precautions While Driving
In Rain
Avoid driving in deep water and on flooded roads. This can damage the engine or
cause electrical component failure.
Other Precautions
If there is a strong impact with something under the vehicle, stop in a safe
location. Check the underside of the vehicle for damage any fluid leaks.
Precautions While Driving NOTICE Do not operate the shift lever while pressing
the accelerator pedal. You could damage the
transmission.
If the ignition switch is turned to ACCESSORY
I or
LOCK
0 while driving, the engine will shut down
and all steering and brake power assist functions
will stop, making it difficult to control the vehicle.
Do not put the shift lever in
N
, as you will lose
engine braking (and acceleration) performance.
During the first 600 miles (1,000 km) of operation,
avoid sudden acceleration or full throttle operation
so as to not damage the engine or powertrain.
Avoid hard braking for the first 200 miles (300 km).
You should also follow this when the brakes are
replaced.

194Driving
When Driving
Automatic Transmission
Automatic Transmission
Creeping
The following conditions cause the engine to run at high revolutions, and increase
creeping:
Immediately after the engine starts. t
When the climate control system is in use. t
Keep the brake pedal firmly depressed when stopped.
Kickdown
Depressing the accelerator pedal while driving uphill may cause the transmission
to drop to a lower gear, unexpectedly increasing vehicle speed. Depress the
accelerator pedal carefully, especially on slippery roads and curves.

195
Continued
Driving
When Driving
Shifting
Change the shift position in accordance with your driving need.
Shift lever positions
Shifting
You cannot turn the ignition switch to LOCK
0 and
remove the key unless the shift lever is in
P.
The vehicle may move forward very slightly even in
N
while the engine is cold.
Depress the brake pedal firmly and, when necessary,
apply the parking brake.
Auomatic transmission models Shifting
Park
Used when parking or starting the
engine
Reverse
Used when backing up
Neutral
Used when idling
Drive
Used for:
Normal driving (gears change t
between 1st and 5th automatically)
Temporarily driving in the sequential t
mode
Drive (S)
Used for:
Automatically changing gears t
between 1st and 4th (4th gear is
used only at high speed)
Driving in the sequential mode t
P
R
N
D
S

196Driving
When Driving
Shifting
Shift Lever Operation
Shift Lever Operation NOTICE When you change the shift lever from
D
to
R and
vice versa, come to a complete stop and keep the
brake pedal depressed.
Operating the shift lever before the vehicle has
come to a complete standstill can damage the
transmission.
Use the shift lever position indicator to check the
lever position before pulling away.
Whichever position the shift lever is in when driving,
a blinking
D
indicator indicates a transmission
problem.
Avoid sudden acceleration and have the
transmission checked by a dealer as soon as
possible.
The fuel supply may be cut off if you drive at engine
speeds in or over the tachometer red zone (engine
speed limit). If this happens, you may experience a
slight jolt.
It may not be possible to operate the shift lever
if the brake pedal is applied while the shift lever
release button is held down.
Depress the brake pedal first.
Tachometer's red zone
Shift Lever Position Indicator
Depress the brake pedal and
press the shift lever release button to
shift.
Shift without pressing the shift lever
release button.
Press the shift lever release button
and shift.M (Sequential Shift mode) Indicator/
Gear Position Indicator

200Driving
When Driving
Shifting
Reverse Lockout
The manual transmission has a lockout mechanism that stops you from accidentally
shifting into
R
from a forward gear while the vehicle is moving at a certain
speed.
If you cannot shift to
R
when the vehicle is stopped, do the following:
1. Depress the clutch pedal, move the shift
lever all the way to the left, and shift
to
R
.
2. If you still cannot shift into
R
, apply the
parking brake, and turn the ignition switch
to ACCESSORY
I or LOCK
0
.
3. Depress the clutch pedal and shift into
R
.
4. Keep depressing the clutch pedal and start
the engine.
Have the vehicle checked by a dealer if you
have to go through this procedure repeatedly.

202Driving
When Driving
Cruise Control
To Set the Vehicle Speed
Press the DECEL /SET button when you reach the desired speed using the
accelerator pedal.
The moment you release the DECEL /SET button, the set speed is fixed, and cruise
control begins. The CRUISE CONTROL indicator comes on.
To Cancel
To cancel cruise control, do any of the
following.:
Press the CANCEL button. t
Press the CRUISE button. t
Depress the brake pedal. t
Depress the clutch pedal. t
The CRUISE CONTROL indicator goes off.
To Set the Vehicle Speed
When not using cruise control:
Turn off cruise control by pressing the CRUISE
button. To Cancel
Resuming the prior set speed:
After cruise control has been canceled, you can still
resume the prior set speed by pressing the RES/
ACCEL button while driving at a speed of at least 25
mph (40 km/h) or more.
CRUISE
Button
CANCEL
ButtonYou cannot set or resume in the following
situations:
When vehicle speed is less than 25 mph (40 km/h)
tWhen the t
CRUISE button is turned off
At vehicle speeds of 22 mph (35 km/h) or less,
cruise control is canceled automatically. DECEL /SET Button
On when cruise control begins.
Press and Release
OnOn

203
Driving
When Driving
Cruise Control
To Adjust the Vehicle Speed
Increase or decrease the vehicle speed using the accelerator and brake pedals, and
set the vehicle speed with the DECEL /SET button on the steering wheel.
To Adjust the Vehicle Speed
Vehicle speed can be increased or decreased also
using the RES/ACCEL or DECEL /SET buttons on the
steering wheel.
RES/ACCEL Button
Each time you press the button, vehicle speed is tincreased by about 1 mph (1.6 km/h).
If you keep it pressed, vehicle speed increases tuntil you release it. This speed is then set.
DECEL /SET Button
Each time you press it, vehicle speed decreases by tabout 1 mph (1.6 km/h).
If you keep it pressed, vehicle speed decreases tuntil you release it. This speed is then set.
DECEL /SET
Button
Press and Release
To decrease speed To increase speed
Decrease vehicle speed with the
brake pedal, then take your foot
off the brake pedal.Use the accelerator pedal
to increase vehicle speed.
The vehicle speed is
set when the button is
released.

204Driving
When Driving
VSA
® (Vehicle Stability Assist), aka ESC (Electronic Stability Control), System
VSA
® (Vehicle Stability Assist), aka ESC (Electronic
Stability Control), System
VSA
® helps to stabilize the vehicle during cornering if the vehicle turns more or less
than what was intended. It also assists in maintaining traction on slippery surfaces.
It does so by regulating engine output and selectively applying the brakes.
VSA
® Operation
VSA
® (Vehicle Stability Assist), aka ESC (Electronic Stability
Control), System
The VSA
® may not function properly if tire type and
size are mixed. Make sure to use the same size and
type of tire, and the air pressures as specified.
When the VSA
® indicator comes on and stays on
while driving, there may be a problem with the
system. While this may not interfere with normal
driving, have your vehicle checked by a dealer
immediately.
VSA
® cannot enhance stability in all driving
situations and does not control the entire braking
system. You still need to drive and corner at speeds
appropriate for the conditions and always leave a
sufficient margin of safety.
The main function of the VSA
® system is generally
known as Electronic Stability Control (ESC). The
system also includes a traction control function.
When VSA
® activates, you may notice
that the engine does not respond to the
accelerator. You may also notice some noise
from the hydraulic system. You will also see
the indicator blink.
VSA
® System
Indicator

Braking
210Driving
Brake System
Parking Brake
Use the parking brake to keep the vehicle stationary when parking.
To a p p l y :
Pull the lever fully up without pressing the
release button.
To r e l e a s e :
1. Pull the lever slightly, and press and hold
the release button.
2. Lower the lever down all the way, then
release the button.
Parking Brake NOTICE Release the parking brake fully before driving. The
rear brakes and axle can be damaged if you drive
with the parking brake applied.If you start driving without fully releasing the
parking brake, a buzzer sounds as a warning, and
"RELEASE PARKING BRAKE" appears on the multi-
information display.
Always apply the parking brake when parking.
To prevent the parking brake from freezing when
the outside temperature is extremely cold, do not
apply it, but do the following: Automatic transmission models Put the shift lever in
P, then use a block or other
wheel chock to stop the wheels from turning.
Manual transmission models Put the shift lever in
R or
1, then use a block or
other wheel chock to stop the wheels from turning.

Braking
Brake System
211
Driving
Foot Brake
Your vehicle is equipped with disc brakes at all four wheels. A power assist helps
reduce the effort needed on the brake pedal. The brake assist system increases the
stopping force when you depress the brake pedal hard in an emergency situation.
The anti-lock brake system (ABS) helps you retain steering control when braking
very hard.
Brake Assist System

P. 2 13
ABS (Anti-lock Brake System)


P. 2 12
Foot Brake
Check the brakes after driving through deep water,
or if there is a buildup of road surface water. If
necessary, dry the brakes by lightly depressing the
pedal several times.
If you hear a continuous metallic friction sound
when applying the brakes, the brake pads need to
be replaced. Have the vehicle checked by a dealer.
Constantly using the brake pedal while going down
a long hill builds up heat, which reduces the brake
effectiveness. Apply engine braking by taking your
foot off the accelerator pedal and downshifting to
a lower gear. With manual transmission use a lower
gear for greater engine braking.
Do not rest your foot on the brake pedal while
driving, as it will lightly apply the brakes and cause
them to lose effectiveness over time and reduce pad
life. It will also confuse drivers behind you.